DLA MS27388 REV C-2003 ELBOW SUBASSEMBLY FLARELESS 90 DEG SWIVEL NUT《90度旋转螺母承插弯管组件》.pdf

1、AMSC N/A 1 of 3 FSC 4730 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. INCH-POUND MS27388C 24 September 2003 SUPERSEDING MS27388B 30 June 1972 DETAIL SPECIFICATION SHEET ELBOW SUBASSEMBLY, FLARELESS, 90, SWIVEL NUT This specification is approved for use by all Dep

2、artments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification and MIL-DTL-27272. NOTES: 1. Dimension A is measured between the hose end of the threaded section of the union and the centerline of the insert. 2. Dime

3、nsion B is measured between the centerline of the elbow and the free end of the insert at its centerline. 3. If required, lockwire holes to be drilled in accordance with SAE AS1043 and suffix L added to the Part or Identifying Number (PIN) (e.g., MS27388-10CL). 4. Any bent tube design of adapter com

4、ponents to the left of plane A-A is acceptable provided the dimensions A and B and the requirements of this specification sheet and the procurement specification are met. 5. The inside diameter (ID) of the elbow shall not be less than the ID of the nipple. Ovality shall not exceed 7.5 percent of the

5、 nominal tubing outside diameter. The minimum wall thickness at the elbow bend shall not be less than .034 inch for the -10 through -20 sizes, and .044 inch for the -24 size. FIGURE 1. Elbow subassembly illustration. Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

6、e from IHS-,-,-MS27388C 2 REQUIREMENTS Intended use. This part is a component of MS27383. Identification of product. The PIN and the manufacturers trademark shall be permanently marked on the part. The PIN for this subassembly shall be as specified in table I (e.g., MS27388-10C). Dimensions. Dimensi

7、ons are in inches. Material. PIN suffix C, corrosion-resistant steel. PIN suffix D. Aluminum alloy. No PIN suffix. Combination of aluminum alloy and corrosion- resistant steel. See applicable specification sheet for other components identified in table I for their material requirements. Finish. Corr

8、osion-resistant steel, do not passivate. Aluminum alloy. Anodize in accordance with MIL-A-8625, type II, dye yellow. Order of precedence. This specification takes precedence over the documents referenced herein. Unless otherwise specified, referenced documents shall be of the issue in effect on the

9、date of solicitation. Elbow subassembly illustration. See figure 1. TABLE I. Elbow subassembly composition. PIN 1/Wire PIN Union, nipple PIN Elbow, nipple end PIN A 2/.035 B 3/.035 MS27388 MS27072 MS27071 MS27394 -10C -10C -10C -10C 1.315 1.392 -10 -10D -10D -12C -12C -12C -12C 1.808 1.626 -12 -12D

10、-12D -16C -16C -16C -16C 1.901 1.776 -16 -16D -16D -20C -20C -20C -20C 2.180 2.056 -20 -20D -20D -24C -24C -24C -24C 2.500 2.438 -24 -24D -24D 1/ If required, lockwire holes to be drilled in accordance with SAE AS1043 and suffix L added to the PIN (e.g., MS27388-10CL). 2/ A is measured between the h

11、ose end of the threaded section of the union and the centerline of the insert. 3/ B is measured between the centerline of the elbow and the free end of the insert at its centerline. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the

12、previous issue, due to the extent of the changes. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27388C 3 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AV DLA - CC Navy - AS Air Force - 99 (Project 4730-0868-067) DLA - CC Review activities: Army - AT, MI Navy - MC, SA, SH Air Force -71 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-