DLA MS27623 REV C-2009 SLEEVE HOSE COUPLING.pdf

1、 MS27623C 14 October 2009 SUPERSEDING MS27623B 29 September 2000 DETAIL SPECIFICATION SHEET SLEEVE, HOSE COUPLING This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this spe

2、cification sheet and MIL-DTL-83296. FIGURE 1. Sleeve dimensions and configuration. AMSC N/A FSC 4730 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27623C 2 PIN A .005 (0.13) inch (mm) B Basic inch (mm) C .005 (0.13) inch (mm) D .005 (0

3、.13) inch (mm) E .005 (0.13) inch (mm) F +.004 -.000 (+0.10) inch (mm) G .005 (0.13) inch (mm) MS27623-4C .375 (9.53) .1672 (4.25) .490 (12.45) .378 (9.60) .265 (6.73) .326 (8.28) .361 (9.17) MS27623-6C .410 (10.41) .2442 (6.20) .625 (15.88) .450 (11.43) .353 (8.97) .422 (10.72) .446 (11.33) MS27623

4、-8C .567 (14.40) .2597 (6.60) .735 (18.67) .560 (14.22) .460 (11.68) .512 (13.00) .546 (13.87) MS27623-10C .655 (16.64) .0622 (1.58) .870 (22.10) .700 (17.78) .597 (15.16) .647 (16.43) .685 (17.40) FIGURE 1. Sleeve dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproductio

5、n or networking permitted without license from IHS-,-,-MS27623C 3 PIN H +.000 -.005 (-0.13) inch (mm) J .003 (0.08) inch (mm) K +.000 -.005 (-0.13) inch (mm) L .005 (0.13) inch (mm) M .005 (0.13) inch (mm) N .005 (0.13) inch (mm) P .005 (0.13) inch (mm) R .005 (0.13) inch (mm) MS27623-4C - .440 (11.

6、18) - - .085 (2.16) .185 (4.70) .275 (6.99) - MS27623-6C - .584 (14.83) - - .100 (2.54) .225 (5.72) .300 (7.62) - MS27623-8C - .663 (16.84) - - .260 (6.60) .360 (9.14) .460 (11.68) - MS27623-10C .760 (19.30) .740 (18.80) .800 (20.32) .012 (.30) .222 (5.64) .347 (8.81) - .104 (2.64) PIN S .002 (0.05)

7、 inch (mm) U inch (mm) Y inch (mm) Z .003 (0.08) inch (mm) AA .003 (0.08) inch (mm) AB inch (mm) AC .005 (0.13) inch (mm) AD .005 (0.13) inch (mm) MS27623-4C .016 (0.41) - - - - 10 .25 - - MS27623-6C .0267 (0.678) .1245 (3.162) .502 (12.75) .543 (13.79) 12 .25 - - MS27623-8C - - - - 8 .50 - - MS2762

8、3-10C - - - - 8 .50 .193 (4.90) .308 (7.82) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances shall be .005 inch (0.13 mm). 4. Radius or break all corners to .005 + .005/-.000 inch, (0.13 +0.13/-0.00 mm) unless otherwi

9、se specified. 5. Unless otherwise specified, surface roughness, in accordance with ASME B46.1, shall not exceed 125 in Ra.6. Dimensioning and tolerancing are in accordance with ASME Y14.5M. 7. In area AX, a dry-film lubricant shall be used as specified in SAE-AS5272. Dry film lubricant in area AY sh

10、all not be cause for rejection. Dry film lubricant shall not be allowed in area AZ. 8. All burrs and slivers shall be removed. FIGURE 1. Sleeve dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27623C 4 REQUI

11、REMENTS: Dimensions and configurations: The design, construction, and physical dimensions shall be in accordance with MIL-DTL-83296 and figure 1, in case of conflict between this specification sheet and MIL-DTL-83296, this specification sheet shall govern. This part is a component of MS27616, MS2761

12、7, MS27618, MS27620, MS27621, MS27633, and MS27634. The item is only procured as an integral part of an adapter assembly. Material: Material shall be corrosion resistant steel (CRES) alloy 17-4PH in accordance with SAE-AMS-5643. Hardness: Hardness shall be Rockwell C 35 to 39 or Rockwell superficial

13、 hardness 30N-55.5 to N-58.5. Finish: Finish shall be passivated as specified in MIL-DTL-83296. PIN example: MS27623 -4 C PIN example: MS27623-4C indicates a sleeve 1/4 inch, CRES. Changes from previous issue. Marginal notations are not used in this revision to identify changes due to the extent of

14、the changes. Referenced documents. In addition to MIL-DTL-83296, this document references the following: MIL-DTL-83298 MS27616 MS27617 MS27618 MS27620 MS27621 MS27633 MS27634 ASME Y14.5M ASME B46.1 SAE-AMS-5643 SAE-AS5272 Specification sheet number Dash size (see figure 1) Material (C for CRES) MS p

15、refix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27623C 5 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AV DLA - CC Navy - AS Air Force - 99 (Project 4730-2008-041) DLA - CC Review activities: Navy - MC, SA Air Force - 71 NOTE: Th

16、e activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-