DLA MS27635 REV C-2009 NIPPLE FLARELESS TUBE TO HOSE SWIVEL NUT.pdf

1、 MS27635C 22 October 2009 SUPERSEDING MS27635B 29 September 2000 DETAIL SPECIFICATION SHEET NIPPLE, FLARELESS, TUBE TO HOSE, SWIVEL NUT This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein sha

2、ll consist of this specification sheet and MIL-DTL-83296. FIGURE 1. Flareless nipple dimensions and configuration. AMSC N/A FSC 4730 INCH-POUND Inches mm .010 .020 0.25 0.51 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27635C 2 FIGURE 1. Flarele

3、ss nipple dimensions and configuration Continued. Inches mm .005 .010 .020 .025 0.13 0.25 0.51 0.62 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27635C 3 Part or Identifying Number (PIN) A .010 (0.25) inch (mm) B .005 (0.13) inch (mm) C (see not

4、e 5) inch (mm) D .005 (0.13) inch (mm) E .005 (0.13) inch (mm) F .005 (0.13) inch (mm) G .005 (0.13) inch (mm) MS27635-4C .583 (14.81) .929 (23.60) .750 (19.05) .379 (9.63) .110 (2.79) .544 (13.82) .041 (1.04) MS27635-6C .748 (19.00) .981 (24.92) .875 (22.23) .361 (9.17) .085 (2.16) .660 (16.76) .04

5、3 (1.09) MS27635-8C .857 (21.77) 1.137 (28.88) 1.000 (25.40) .400 (10.16) .100 (2.54) .813 (20.65) MS27635-10C 1.010 (25.65) 1.388 (35.26) 1.250 (31.75) .338 (8.59) .100 (2.54) .989 (25.12) .037 (.94) PIN H .050 inch (mm) J +.000 - .005 (-0.13) inch (mm) K .005 (0.13) inch (mm) L .005 (0.13) inch (m

6、m) M .010 (0.25) inch (mm) N .005 (0.13) inch (mm) P .02 (0.51) inch (mm) MS27635-4C .100 (2.54) .250 (6.35) .420 (10.67) .72 (18.29) MS27635-6C .343 (8.71) .495 (12.57) .84 (21.34) MS27635-8C .445 (11.30) .610 (15.49) .783 (19.89) .030 (0.76) .97 (24.64) MS27635-10C .588 (14.94) .762 (19.35) .150 (

7、3.81) 1.22 (30.99) PIN R .50 S .005 (0.13) inch (mm) Thread T Pitch diameter U 5 V .005 (0.13) inch (mm) MS27635-4C .161 (4.09) .625-18UNJF-3A .5889/.5854 (14.958/14.869) 45 MS27635-6C .271 (6.88) .750-16UNJF-3A .7094/.7056 (18.019/17.922) MS27635-8C .375 (9.53) .875-24UNJS-3A .8479/.8448 (21.537/21

8、.558) 30 .050 (1.27) MS27635-10C 10 .465 (11.81) 1.0625-20UNJ-3A 1.0300/1.0266 (26.162/26.076) 45 FIGURE 1. Flareless nipple dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27635C 4 PIN W .005 (0.13) inch (

9、mm) AA .005 (0.13) inch (mm) AB inch (mm) AC .005 (0.13) inch (mm) MS27635-4C .825 (20.96) .069 (1.75) .625 (15.88) +.000 -.009 (-0.23) .138 (3.51) MS27635-6C .962 (24.43) .092 (2.34) .750 (19.05) .185 (4.70) MS27635-8C 1.100 (27.94) .095 (2.41) .875 (22.23) +.000 -.007 (-0.18) .190 (4.83) MS27635-1

10、0C 1.375 (34.93) .125 (3.18) 1.062 (26.97) +.000 -.008 (-0.20 .250 (6.35) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances shall be .005 inch (0.13 mm). 4. Unless otherwise specified, radius or break all corners to .0

11、05 + .005/-.000 inch (0.13 +0.13/-0.00 mm). 5. Unless otherwise specified, surface roughness, in accordance with ASME B46.1, shall not exceed 125 in Ra. 6. In area X, a dry-film lubricant shall be used as specified in MIL-PRF-46010 or SAE-AS5272. Dry-film lubricant shall be allowed in area Y. Dry-fi

12、lm lubricant shall not extend beyond area Z. 7. For dimension C, use commercial stock size tolerance as specified in SAE-AMS2241. 8. All burrs and slivers shall be removed. 9. Dimensioning and tolerancing are in accordance with ASME Y14.5M. FIGURE 1. Flareless nipple dimensions and configuration - C

13、ontinued. REQUIREMENTS: Dimensions and configurations: The design, construction, and physical dimensions shall be in accordance with MIL-DTL-83296 and figure 1, in case of conflict between this specification sheet and MIL-DTL-83296, this specification sheet shall govern. This is a design specificati

14、on sheet for manufacturing purposes. The item is only procured as an integral part of adapter assembly MS27632. This part for use with MIL-DTL-83298 hose and hose assemblies in accordance with MIL-DTL-32330. Material: Material shall be a corrosion resistant steel (CRES), class 304, condition B, in a

15、ccordance with ASTM A276. Sizes -4, -6, and -8 shall have a minimum yield of 70,000 psi and size -10 shall have a minimum yield of 60,000 psi. Finish: Finish shall be passivated in accordance with MIL-DTL-83296. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

16、m IHS-,-,-MS27635C 5 PIN example: MS27635 -4 C PIN example: MS27635-4C indicates a nipple 1/4 inch, CRES. Changes from previous issue. Marginal notations are not used in this revision to identify changes due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83296, this docum

17、ent references the following: MIL-DTL-32330 MIL-DTL-83298 MIL-PRF-46010 MS27632 ASME B46.1 ASME Y14.5M ASTM A276 SAE-AMS2241 SAE-AS5272 SAE-AS8879 SAE-AS33514 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AV DLA - CC Navy - AS Air Force - 99 (Project 4730-2008-065) DLA - CC Review activ

18、ities: Navy - MC, SA Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Specification sheet number Dash size (see figure 1) Material (C for CRES) MS prefix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-