ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:77.29KB ,
资源ID:696877      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-696877.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(DLA MS27781 REV D-2011 SWITCH TOGGLE ONE POLE ENVIRONMENTALLY SEALED LEVER LOCK INTEGRATED WIRE TERMINALS.pdf)为本站会员(confusegate185)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

DLA MS27781 REV D-2011 SWITCH TOGGLE ONE POLE ENVIRONMENTALLY SEALED LEVER LOCK INTEGRATED WIRE TERMINALS.pdf

1、AMSC N/A FSC 5930 INCH-POUND MS27781D 18 April 2011 SUPERSEDING MS27781C 28 September 1987 DETAIL SPECIFICATION SHEET SWITCH, TOGGLE, ONE POLE, ENVIRONMENTALLY SEALED, LEVER LOCK, INTEGRATED WIRE TERMINALS This specification is approved for use by all Departments and Agencies of the Department of De

2、fense. The complete requirements for acquiring the switch described herein shall consist of this specification and the latest issue of MIL-DTL-3950. FIGURE1. Dimensions and configuration Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27781D 2 NOTE

3、S: 1. Dimensions are inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerance is .020 (0.51 mm) for two place decimals and .005 (0.13 mm) for three place decimals. 3. For hardware detail specifications see appendix of MIL-DTL-3950. 4. Contact instal

4、ling/ removal tool in accordance with MIL-I-81969/14-03. 5. Grommet sealing plug, in accordance with MS27488A16. 6. Terminal shall adequately accept a wire contact within dimensional limits of SAE-AS39029/1-102. 7. Direction of internal mechanism movement is opposite to the direction of the toggle m

5、ovement. FIGURE1. Dimensions and configuration Continued REQUIREMENTS Maximum weight is .108 pound. The force required to release the locking mechanism shall be 3 to 5 pounds. Locking arrangement: Positive locking shall be accomplished and shall prevent motion of the toggle movement The locking mean

6、s at the top of the toggle bushing shall be capable of withstanding a torque of 20 inch-pounds applied in both directions immediately following the humidity test. The sealing grommet shall seal on a smooth wire insulation of .068 (1.73 mm) to .103 (2.62 mm) diameters. The terminal end of switch shal

7、l be color coded blue to indicate contact size. Sealing plugs may be used in nonfunctional grommet holes. Electrical rating: See table I. Inches mm Inches mm .005 0.13 .432 10.97 .008 0.20 .469 11.91 .012 0.30 .47 11.9 .020 0.51 .635 16.13 .060 1.52 1.05 26.7 .076 1.93 1.140 28.96 .38 9.7 1.270 32.2

8、6 .42 10.7 1.662 42.21 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27781D 3 FIGURE 2 . Locking Combinations. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27781D 4 TABLE I: Detail Requiremen

9、ts Test Requirements a) During all tests. Switches shall be fully wired with appropriate wire and terminal contacts. b) Contact voltage drop- the contact drop with two terminals and the switch contact in series shall not exceed 8 millivolts measured from one wire contact through the contacts to the

10、other wire contacts. MS Part No. Available Locking combinations Circuit with Toggle Lever In Current capacity (amperes) 28 volts DC Current capacity(amperes) 115 volts, 60 and 400 Hertz AC Keying side Center Opposite keying side Lamp Load circuit Resistive circuit Inductive circuit Lamp- Load circui

11、t Resistive circuit Inductive circuit MS27781-21 ALL 1-2 ON OFF 2-3 ON 5 20 15 3 15 10 MS27781-22 D, F, G OFF NONE 2-3 ON MS27781-23 D,F,G 1-2 ON NONE 2-3 ON MS27781-24 E,F,K,M NONE OFF 2-3 ON MS27781-25 F NONE MOM OFF 2-3 ON 4 15 10 2 15 7 MS27781-26 F 1-2 MOM. ON NONE 2-3 ON MS27781-27 E,L,N 1-2 M

12、OM. ON OFF 2-3 MOM ON MS27781-28 E 1-2 MOM ON OFF NONE MS27781-29 F MOM OFF NONE 2-3 ON MS27781-30 F 1-2 MOM OFF NONE OFF MS27781-31 E,F,K,L,M,N 1-2 MOM ON OFF 2-3 ON MS27781-32 E NONE ON 1-2 2-3 MOM ON MS27781-33 E,F,K,M NONE ON 1-2 2-3 ON 5 20 15 3 15 10 Provided by IHSNot for ResaleNo reproductio

13、n or networking permitted without license from IHS-,-,-MS27781D 5 Referenced documents MIL-DTL-3950 Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing activity Army CR DLA CC Navy AS Air Forc

14、e 85 (Project 5930-2011-062) DLA CC Review activities Army AR, AV, MI Navy EC, MC Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/ . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1