DLA MS28746 REV E-2007 FITTING END - HOSE SWIVEL DETACHABLE 45 FLANGE 4 BOLT《45度可拆卸旋转4螺栓法兰软管》.pdf

1、 INCH-POUNDMS28746E 14 May 2007 SUPERSEDING MS28746D 22 September 2000 DETAIL SPECIFICATION SHEET FITTING END - HOSE, SWIVEL, DETACHABLE, 45 FLANGE, 4 BOLT This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product

2、described herein shall consist of this specification sheet and MIL-DTL-5070. FIGURE 1. Flange dimensions and configuration. AMSC N/A FSC 4730Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS28746E 2 Dash number Tubing OD inch (mm) A max inch (mm) B

3、max inch (mm)C inch (mm)D dia inch (mm)E max dia inch (mm)F (see note 7)inch (mm) Weight (approx.) pounds (kg) -24 1.500 (38.10) 4.047 (102.79) 1.844 (46.84) .812 (20.62) 1.281 (32.54) 2.188 (55.58) .625 (15.88) 1.013 (0.46) -32 2.000 (50.80) 4.859 (123.42) 2.250 (57.15) .953 (24.21) 1.750 (44.45) 2

4、.625 (66.68) .875 (22.23) 1.264 (0.57) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are as follows: angles .5; decimals .005 inch (0.13 mm). 4. If width diametrically across flats or hex is less than the body diam

5、eter, the flats or hex shall extend the full length of the body. 5. Diameters after plating must be concentric with each other within .005 inch (0.13 mm) total indicator reading. 6. The manufacturers Part or Identifying Number (PIN) and CAGE Code shall be permanently marked on the body. 7. Hex or fl

6、ats shall fit standard wrench openings. 8. Break all sharp edges and remove all hanging burrs and slivers that might become dislodged under usage. FIGURE 1. Flange dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

7、,-,-MS28746E 3 REQUIREMENTS: Dimensions and configurations: The design, construction, and physical dimensions shall be in accordance with MIL-DTL-5070 and figure 1 in case of conflict between this drawing and MIL-DTL-5070, this drawing shall govern. Materials: Shall be in accordance with MIL-DTL-507

8、0. Finish: Shall be in accordance with MIL-DTL-5070. PIN example: MS 28746 -24 CZMaterial/finish designator, see table I Dash number on figure 1 Specification number MS prefix TABLE I. Code for material and finish. 1/ Code Material/finish CC Carbon Steel - cadmium plating CZ Carbon steel - zinc plat

9、ing SS Corrosion resistant steel - N/A TA Titanium - anodized or fluoride phosphated. 1/ Finishes “CC”, “CZ” and “SS” are applicable only to flange, nipple, and shoulder made of steel alloy. No mixing of steel material/finish types shall be allowed. To the users of this document, it is recommended t

10、hat the use of carbon steel material with cadmium plating be used only when the other materials and finishes specified in this document cannot meet performance requirements. Identification of product. The PIN and the manufacturers Commercial and Government Entity (CAGE) Code or trademark shall be pe

11、rmanently marked on the flange or on a removable tag securely attached to the flange. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. This document references

12、 MIL-DTL-5070. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS28746E 4 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 99 (Project 4730-2005-058) DLA - CC Review activities: Army - AV Air Force - 11, 71

13、 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-