DLA MS28753 REV E-2012 FITTING END SELF-SEALING FUEL HOSE SWIVEL DETACHABLE FLANGED STRAIGHT.pdf

1、AMSC N/A FSC 4730 DETAIL SPECIFICATION SHEET FITTING END, SELF-SEALING FUEL HOSE, SWIVEL, DETACHABLE, FLANGED, STRAIGHT This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of th

2、is specification sheet. FIGURE 1. Straight fuel hose fitting. INCH-POUND MS28753E 5 June 2012 SUPERSEDING MS28753D 6 August 2010 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS28753E 2 Size designator Nominal tubing and hose size (REF) Flange PIN

3、(see notes 4 and 5) A Max inch (mm) B Max inch (mm) C Min (see note 6) inch (mm) D Max inch (mm) 16 1 (1.000) MS20756*16 3.141 (79.78) 2.000 (50.80) .813 (20.65) 1.953 (49.61) 20 1 (1.250) MS20756*20 3.141 (79.78) 2.000 (50.80) 1.047 (26.59) 2.313 (58.75) 24 1 (1.500) MS20756*24 3.078 (78.18) 2.000

4、(50.80) 1.281 (32.54) 2.563 (64.41) 32 2 (2.000) MS20756*32 3.500 (88.90) 2.250 (57.15) 1.750 (44.45) 3.125 (79.38) 40 2 (2.500) MS20756*40 3.891 (98.83) 2.500 (63.50) 2.250 (57.15) 3.625 (92.08) 48 3 (3.000) MS20756*48 3.891 (98.83) 2.500 (63.50) 2.875 (73.03) 4.438 (112.73) Size designator E +.000

5、 -.005 (0.13) inch (mm) F (see note 6) +.000 -.005 (0.13) inch (mm) G Max (see note 6) inch (mm) H Min inch (mm) J Min inch (mm) 16 .156 (3.96) 1.500 (28.10) 1.188 (30.18) .375 (9.53) 1.343 (34.11) 20 .156 (9.36) 1.844 (46.84) 1.500 (38.10) .500 (12.70) 1.656 (42.06) 24 .188 (4.48) 2.125 (53.98) 1.7

6、50 (44.45) .500 (12.70) 1.906 (48.41) 32 .188 (4.48) 2.750 (69.85) 2.375 (60.33) .625 (15.88) 2.531 (64.29) 40 .188 (4.48) 3.281 (83.34) 2.875 (73.03) 1.000 (25.40) 3.051 (77.50) 48 .188 (4.48) 3.781 (96.04) 3.375 (85.73) 1.250 (31.75) 3.250 (82.55) NOTES: 1. Dimensions are in Inches. 2. Metric equi

7、valents are given for information only. 3. Unless otherwise specified, tolerances: decimals .010 (0.25 mm); angles .01. 4. Part or Identifying Number (PIN). 5. Material designator D, W or T see MS20756. 6. Dimensions C, F and G shall be concentric within .010 inch (0.25 mm) full indicator reading. F

8、IGURE 1. Straight fuel hose fitting - Continued. inch mm .005 .015 .062 .125 0.13 0.38 1.58 3.18 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS28753E 3 REQUIREMENTS: Material: Materials shall be in accordance with table I and SAE-AS4841. TABLE I.

9、 Material designators. Material designator Alloy Finish D Aluminum alloy 2014 or 2024 Anodize in accordance with MIL-A-8625, type II. 1/ W Aluminum alloy 7075 Anodize in accordance with MIL-A-8625, type II. 1/ Dash (-) Titanium 2/ Fluoride phosphated in accordance with SAE-AMS2486 3/ T Titanium 2/ A

10、nodized in accordance with SAE-AMS2488, type 2 1/ Aluminum alloys 2014 and 2024 aluminum shall be dyed light blue. Aluminum alloy 7075 shall be dyed brown. 2/ Titanium shall not be used in oxygen systems. 3/ Color equivalent to numbers /36076, /36081, /36099, /36118, /36134, /36152, /36170, /36173,

11、and /36176 in accordance with FED-STD-595. Hex or flats shall fit standard wrench openings. Surface roughness shall be in accordance with ASME-B46.1. Remove all burrs and sharp edges. The interior surface of the fitting shall be smooth and free from projections. PIN. The PIN shall consist of the pre

12、fix MS followed by the specification sheet number, letter for material designator, and a number for the size. MS28753 W 16 Example of PIN: MS28753W16 indicates a straight swivel with flange, aluminum, 1 inch hose or tubing size. Fittings shall be permanently marked with the applicable MS PIN on an u

13、nfinished surface of the nipple. Approximate weights are shown in table II. MS prefix Specification sheet number Material (see table I) Size designator (see figure 1) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS28753E 4 TABLE II. Approximate we

14、ight. Size designator Weight (Approx) lb (g) Aluminum Titanium 16 .261 (118.4) .43 (195.0) 20 .299 (135.6) .49 (222.3) 24 .305 (138.3) .50 (226.8) 32 .325 (147.4) .54 (244.9) 40 .607 (275.3) 1.00 (453.6) 48 .954 (432.7) 1.58 (716.7) Intended use: Hose assemblies using hose in accordance with MIL-PRF

15、-7061. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. This document references the following: FED-STD-595/36076 FED-STD-595/36081 FED-STD-595/36099 FED-STD-5

16、95/36118 FED-STD-595/36134 FED-STD-595/36152 FED-STD-595/36170 FED-STD-595/36173 FED-STD-595/36176 MIL-A-8625 MIL-PRF-7061 MS20756 ASME-B46.1 SAE-AMS2486 SAE-AMS2488 SAE-AS4841 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AV DLA - CC Navy - AS Air force - 99 DLA - CC (Project 4730-2012

17、-026) Review activities: Navy - MC, SH Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-