DLA MS28754 REV E-2012 FITTING END SELF-SEALING FUEL HOSE SWIVEL DETACHABLE FLANGED 45.pdf

1、AMSC N/A FSC 4730 DETAIL SPECIFICATION SHEET FITTING END, SELF-SEALING FUEL HOSE, SWIVEL, DETACHABLE, FLANGED, 45 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this spe

2、cification sheet. FIGURE 1. 45 fuel hose fitting. INCH-POUND MS28754E 5 June 2012 SUPERSEDING MS28754D 6 August 2010 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS28754E 2 Size designator Nominal tubing and hose size (REF) Flange PIN (see notes 5

3、 and 6) A max. inch (mm) B max. inch (mm) C min dia. (see note 7) inch (mm) D dia. max. inch (mm) 16 I (1.000) MS20756*16 3.672 (93.27) 2.000 (50.80) .813 (20.65) 1.953 (49.61) 20 1 (1.250) MS20756*20 3.797 (96.44) 2.000 (50.80) 1.047 (26.59) 2.313 (58.75) 24 1 (1.500) MS20756*24 4.219 (107.16) 2.00

4、0 (50.80) 1.281 (32.54) 2.563 (65.10) 32 2 (2.000) MS20756*32 4.875 (123.83) 2.250 (57.15) 1.750 (44.45) 3.125 (79.38) 40 2 (2.500) MS20756*40 5.438 (138.13) 2.500 (63.50) 2.203 (55.96) 3.625 (92.08) 48 3 (3.000) MS20756*48 5.969 (151.61) 2.500 (63.50) 2.828 (71.83) 4.438 (138.13) Size designator E

5、+.000 -.005 (0.13) inch (mm) F dia. +.000 -.005 (0.13) (see note 7) inch (mm) G max dia. (see note 7) inch (mm) H min. inch (mm) J min. inch (mm) K dia. max. inch (mm) 16 .156 (3.96) 1.500 (38.10) .188 (4.78) .375 (9.53) 1.343 (34.11) .656 (16.66) 20 .156 (3.96) 1.844 (46.84) .500 (12.70) .500 (12.7

6、0) 1.656 (42.06) .656 (16.66) 24 .188 (4.78) 2.125 (53.98) .750 (19.05) .500 (12.70) 1.906 (48.41) .813 (20.65) 32 .188 (4.78) 2.750 (69.85) 2.375 (60.33) .625 (15.88) 2.531 (64.29) .953 (24.21) 40 .188 (4.78) 3.281 (83.34) 2.875 (73.03) 1.000 (25.40) 3.031 (76.99) 1.031 (26.19) 48 .188 (4.78) 3.781

7、 (96.04) 3.375 (85.73) 1.250 (31.75) 3.250 (85.22) 1.391 (35.33) FIGURE 1. 45 fuel hose fitting - Continued. inch mm .003 .005 .015 .030 .062 .125 0.08 0.13 0.38 0.76 1.57 3.18 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS28754E 3 NOTES: 1. Dime

8、nsions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances: decimals .010 (0.25 mm); angles .01. 4. Dimensions and finishes are the same as detail X unless otherwise noted. 5. Part or Identifying Number (PIN). 6. Material designator D, W or

9、T see MS20756. 7. Diameters C, F and G shall be concentric within .010 inch (0.25 mm) FIM. 8. The true circular cross section is not required within angle Y, however, a ball .031 inch (0.79 mm) smaller than C must pass through. Nipple ID within angle Y shall not exceed C. FIGURE 1. 45 fuel hose fitt

10、ing - Continued. REQUIREMENTS: Material: Materials and finish shall be in accordance with table I and SAE-AS4841. TABLE I. Material and finish designators. Material designator Alloy Finish D Aluminum alloy 2014 or 2024 Anodize in accordance with MIL-A-8625, type II. 1/ W Aluminum alloy 7075 Anodize

11、in accordance with MIL-A-8625, type II. 1/ Dash (-) Titanium 2/ Fluoride phosphated in accordance with SAE-AMS2486 3/ T Titanium 2/ Anodized in accordance with SAE-AMS2488, type 2 1/ Aluminum alloys 2014 and 2024 aluminum shall be dyed light blue. Aluminum alloy 7075 shall be dyed brown. 2/ Titanium

12、 shall not be used in oxygen systems. 3/ Color equivalent to numbers /36076, /36081, /36099, /36118, /36134, /36152, /36170, /36173, and /36176 in accordance with FED-STD-595. Fittings must swivel through 360 with sufficient clearance to allow use of standard wrenches on the nut when the axis of the

13、 hose is aligned over the stud or capscrew. Hex or flats shall fit standard wrench openings. Surface roughness shall be in accordance with ASME-B46.1. Remove all burrs and sharp edges. The interior surface of the fitting shall be smooth and free from projections. Provided by IHSNot for ResaleNo repr

14、oduction or networking permitted without license from IHS-,-,-MS28754E 4 PIN. The PIN shall consist of the prefix MS followed by the specification sheet number, letter for material designator, and a number for the size. MS28754 W 16 Example of PIN: MS28754W16 indicates a swivel with 45 flange, alumi

15、num, 1 inch hose or tubing size. Fittings shall be permanently marked with the applicable MS PIN on an unfinished surface of the nipple. Approximate weights are shown in table II. TABLE II. Approximate weight. Size Weight lb (Approx) Aluminum Titanium 16 .735 (333.4) 1.21 (548.8) 20 .830 (376.5 1.37

16、 (621.4) 24 .840 (381.0) 1.39 (630.5) 32 1.064 (482.6) 1.76 (798.3) 40 1.300 (589.7) 2.15 (975.2) 48 1.650 (748.4) 2.73 (1238.3 Intended use: Hose assemblies using hose in accordance with MIL-PRF-7061. Changes from previous issue. Marginal notations are not used in this revision to identify changes

17、with respect to the previous issue, due to the extent of the changes. Referenced documents. This document references the following: FED-STD-595/36076 FED-STD-595/36081 FED-STD-595/36099 FED-STD-595/36118 FED-STD-595/36134 FED-STD-595/36152 FED-STD-595/36170 FED-STD-595/36173 FED-STD-595/36176 MIL-A-

18、8625 MIL-PRF-7061 MS20756 ASME-B46.1 SAE-AMS2486 SAE-AMS2488 SAE-AS4841 MS prefix Specification sheet number Material (see table I) Size designator (see figure 1) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS28754E 5 CONCLUDING MATERIAL Custodia

19、ns: Preparing activity: Navy - AS DLA - CC Air Force - 99 DLA - CC (Project 4730-2012-027) Review activities: Navy - SA Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-