DLA MS35673 REV B-2011 PIN GROOVED HEADLESS 鈥 LONGITUDINAL TAPER GROOVE BRASS.pdf

1、AMSC N/A FSC 5315 INCH-POUND MS35673B 31 August 2011 SUPERSEDING MS35673A 17 March 1965 DETAIL SPECIFICATION SHEET PIN, GROOVED, HEADLESS LONGITUDINAL TAPER GROOVE, BRASS This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for a

2、cquiring the product described herein shall consist of this specification sheet and procurement specification NASM20700. B L .010 EARFIGURE 1. Pin. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35673B 2 TABLE I. Dash Numbers and Dimensions. REQUI

3、REMENTS: 1. Material: Brass, Bar or wire, hard, in accordance with the procurement specification. 2. Protective Coating: Black Oxide in accordance with the procurement specification. 3. Application: Grooved pins are locked securely in place by elastic deformation eliminating the need for tapping or

4、reaming of tapered or sized holes. NOMINAL SIZE 3/64 1/16 5/64 3/32 A MAX MIN .0469 .0459 .0625 .0615 .0781 .0771 .0938 .0928 E CROWN HEIGHT REF - .0065 .0087 .0091 R RADIUS MAX MIN - - .0881 .0681 .1037 .0837 .1350 .1150 RECOMMENDED MAX HOLE SIZE MIN .0478 .0465 .0640 .0625 .0798 .0781 .0956 .0938

5、SINGLE SHEAR MIN STRENGTH LBS 70 120 190 270 L LENGTH DASH NO. B .001 DASH NO. B .001 DASH NO. B .001 DASH NO. B .001 .088 .250 .375 201 202 203 .051 .051 .051 206 207 .068 .068 211 212 .084 .084 216 .101 .500 .625 .750 204 205 .051 .051 208 209 210 .068 .068 .068 213 214 215 .084 .084 .084 217 218

6、219 .101 .101 .101 1.000 220 .101 NOMINAL SIZE 1/8 5/32 3/16 1/4 A MAX MIN .1250 .1230 .1563 .1543 .1875 .1855 .2500 .2480 E CROWN HEIGHT REF .0130 .0170 .0180 .0260 R RADIUS MAX MIN .1662 .1462 .1975 .1775 .2600 .2400 .3225 .3025 RECOMMENDED MAX HOLE SIZE MIN .1271 .1250 .1587 .1563 .1903 .1875 .25

7、34 .2500 SINGLE SHEAR MIN STRENGTH LBS 490 760 1100 1960 L LENGTH DASH NO. B .002 DASH NO. B .002 DASH NO. B .002 DASH NO. B .002 .500 .625 .750 221 222 223 .134 .134 .134 227 228 229 .166 .166 .166 233 234 .198 .198 241 242 .263 .263 1.000 1.250 1.500 224 225 226 .133 .132 .132 230 231 232 .165 .16

8、4 .164 235 236 237 .198 .197 .197 243 244 245 .263 .263 .262 1.750 2.000 2.250 238 239 240 .197 .196 .196 246 247 248 .262 .262 .262 2.500 2.750 249 250 .261 .261 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35673B 3 4. Dimensions: All dimension

9、s are in inches, unless otherwise specified. 5. Part Number: The MS part number pins consists of the MS number, plus the dash number. Example: MS35673-201. NOTES: 1. “ B” is the expanded diameter as measured with ring gage. 2. Ends of pins may be square with .01-inch to .02-inch radius on the edges.

10、 3. For design feature purposes, this standard takes precedence over procurement documents referenced herein. 4. Referenced documents shall be of the issue in effect on date of invitations for bid. 5. Changes from previous issue. Marginal notations are not used in this revision to identify changes w

11、ith respect to the previous issue due to the extent of the changes. MILITARY INTEREST Preparing activity: DLA - IS Custodians: Army AR Navy AS Air Force 99 (Project 5315-2011-001) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-