DLA MS39199 REV G-2012 NIPPLE TUBE-SAFETY SLEEVE COMPRESSION TYPE BULKHEAD MOUNTING.pdf

1、AMSC N/A FSC 4730 MS39199G 30 August 2012 SUPERSEDING MS39199F 1 February 2002 DETAIL SPECIFICATION SHEET NIPPLE, TUBE-SAFETY SLEEVE COMPRESSION TYPE, BULKHEAD MOUNTING This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring

2、 the product described herein shall consist of this specification sheet. FIGURE 1. Nipples, tube-safety sleeve compression type, bulkhead mounting. . Inactive for new design after 29 December 1967. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

3、HS-,-,-MS39199G 2 TABLE I. Nipples, tube-safety sleeve compression type, bulkhead mounting. 1/ 2/ Dash No. Tube OD B C Thread Length D Thread Length E F G H J 1 1/8 5/16 24UNF-2A 7/32 11/16 .135 .139 13/64 1/8 9/32 3/32 2 3/16 3/8 24UNF-2A 7/32 3/4 .196 .200 1/4 5/32 9/32 1/8 3 1/4 1/2 20UNF-2A 21/6

4、4 29/32 .261 .265 19/64 13/64 13/32 13/64 4 5/16 9/16 18UNF-2A 21/64 51/64 .324 .328 19/64 13/64 13/32 13/64 5 3/8 5/8 18UNF-2A 23/64 1-23/64 .386 .390 19/64 13/64 7/16 9/32 6 1/2 3/4 16UNF-2A 11/32 1-11/32 .514 .518 5/16 13/64 7/16 27/64 7 5/8 15/16 16UN-2A 23/64 1-3/8 .641 .645 11/32 15/64 15/32 1

5、/2 8 3/4 1-1/16 16UN-2A 23/64 1-13/32 .766 .770 11/32 13/64 15/32 21/32 9 7/8 1-3/16 16UN-2A 23/64 1-13/32 .891 .895 11/32 13/64 15/32 23/32 10 1 1-5/16 16UN-2A 23/64 1-7/16 1.016 1.020 13/32 13/64 15/32 7/8 11 1-1/4 1-5/8 16UN-2A 7/16 1-35/64 1.270 1.274 13/32 13/64 35/64 1-5/64 12 1-1/2 1-7/8 16UN

6、-2A 15/32 1-23/32 1.520 1.524 31/64 13/64 34/64 1-11/32 TABLE I. Nipples, tube-safety sleeve compression type, bulkhead mounting- Continued. 1/ 2/ K L M N 1/2 1-1/4 1-7/8 1/2 9/16 1-5/16 2 9/16 11/16 1-21/32 2-15/32 11/16 3/4 1-17/32 2-9/32 13/16 13/16 2-1/8 3 13/16 15/16 2-1/8 3-3/16 15/16 1-1/8 2-

7、3/16 3-1/4 1-1/8 1-1/4 2-1/4 3-7/16 1-1/4 1-3/8 2-1/4 3-7/16 1-3/8 1-1/2 2-5/16 3-1/2 1-1/2 1-13/16 2-9/16 3-13/16 1-13/16 2-1/16 2-7/8 4-1/4 2-1/16 1/ Dimensions are in inches. 2/ This illustration is for identification and is not intended to restrict designs or shapes not dimensioned Provided by I

8、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39199G 3 REQUIREMENTS: Dimensions and configuration: See figure 1. Nipples. See table I. Tolerances: Unless otherwise specified, decimals .005, fractions 1/64, degrees 2. Threads: The threads shall be in accordanc

9、e with FED-STD-H28. Material: Code Material: C Carbon Steel bar, type AISI-C-1112, C-1113, C-1117, C-1118 or C-1137 in accordance with SAE AIR4127. F Alloy steel in accordance with SAE AIR4127. S Corrosion resistant steel in accordance with SAE AMS5659, SAE AMS5862, or, alloy 15-5 PH in accordance w

10、ith ASTM A564/A564M type XM-12 or UNS S15500 or SAE AMS 5665. Finish: Code Chemical Finish; C Carbon steel: Cadmium in accordance SAE AMS-QQ-P-416, type II, class 3, 200 inches to 300 inches (5.08 m to 7.62 m) thick. F Alloy steel. Cadmium in accordance SAE AMS-QQ-P-416, type II, class 3, 200 inches

11、 to 300 inches (5.08 m to 7.62 m) thick. S Corrosion resistant steel: Passivate in accordance with SAE AMS2700, type 6 or 7. Z Steel, alternative chem finish: in accordance with ASTM B633, type VI, FeZn 25. Part or Identifying Number (PIN) example: (PIN covers the complete item with nuts and sleeves

12、.) Guidance on use of alternative parts with less hazardous or non-hazardous materials. This specification provides an alternate material, zinc finish via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function requirements of their application.

13、Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the MS 27612 -8 C Z If finish code same as material code, then use only one code. Material code Dash size

14、 Specification number MS prefix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39199G 4 Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this

15、document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. This document references the following: FED-STD-H28 SAE AMS 5665 ASTM A564/A564M SAE AMS5862 ASTM B633 SAE AMS2700 SAE AIR4127 SAE AMS-QQ-P-416 SAE AMS5659 M

16、S39210 MS39212 CONCLUDING MATERIAL Custodians: Preparing activity: Army AT DLA - CC Air Force - 99 DLA CC (Project 4730-2012-036) Review activities: Army-AR Air Force-71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-