DLA MS39201 REV G-2012 NIPPLE TUBE-SAFETY SLEEVE COMPRESSION TYPE.pdf

1、AMSC N/A FSC 4730 MS39201G 30 August 2012 SUPERSEDING MS39201F 1 February 2002 DETAIL SPECIFICATION SHEET NIPPLE, TUBE-SAFETY SLEEVE COMPRESSION TYPE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product descri

2、bed herein shall consist of this specification sheet. FIGURE 1. Nipples, tube-safety sleeve compression type. INCH-POUND Inactive for new design after 29 December 1967. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39201G 2 TABLE I. Nipples, tube

3、-safety sleeve compression type. 1/ 2/ Dash No. Tube OD B Threads C Thread Length D E F G 1 1/8 1/8 5/16 24UNF-2A 7/32 3/32 .135 .139 7/32 1/8 2 3/16 3/16 3/8 24UNF-2A 7/32 1/8 .196 .200 1/4 11/64 3 1/4 1/4 1/2 20UNF-2A 21/64 13/64 .261 .265 19/64 13/64 4 5/16 5/16 9/16 18UNF-2A 21/64 15/64 .324 .32

4、8 19/64 13/64 5 3/8 3/8 5/8 18UNF-2A 23/64 9/32 .386 .390 19/64 13/64 6 1/2 7/16 3/4 16UNF-2A 11/32 27/64 .514 .518 5/16 13/64 7 1/2 1/2 3/4 16UN-2A 11/32 27/64 .514 .518 5/16 13/64 8 5/8 5/8 15/16 16UN-2A 23/64 1/2 .641 .645 11/32 15/64 9 3/4 3/4 1-1/16 16UN-2A 23/64 21/32 .766 .770 11/32 13/64 10

5、7/8 7/8 1-3/16 16UN-2A 23/64 23/32 .891 .895 11/32 13/64 11 1 1 1-5/16 16UN-2A 23/64 7/8 1.016 1.020 13/32 13/64 12 1-1/4 1-1/4 1-5/8 16UN-2A 7/16 1-3/32 1.270 1.274 13/32 13/64 13 1-1/2 1-1/2 1-7/8 16UN-2A 15/32 1-11/32 1.520 1.524 15/32 13/64 See notes at end of table. Provided by IHSNot for Resal

6、eNo reproduction or networking permitted without license from IHS-,-,-MS39201G 3 TABLE I. Nipples, tube-safety sleeve compression type - Continued. 1/ 2/ Dash No. H Threads J K L M N O P Q R S 1 5/16 24UNF-2A 7/32 3/32 .135 .139 7/32 1/8 9/32 9/32 7/16 3/4 1-5/16 2 3/8 24UNF-2A 7/32 1/8 .196 .200 1/

7、4 11/64 9/32 9/32 1/2 49/64 1-5/16 3 1/2 20UNF-2A 21/64 13/64 .261 .265 19/64 13/64 13/32 13/32 5/8 1 1-3/4 4 9/16 18UNF-2A 21/64 15/64 .324 .328 19/64 13/64 13/32 13/32 11/16 1 1-3/4 5 5/8 18UNF-2A 23/64 9/32 .386 .390 19/64 13/64 7/16 7/16 3/4 1-3/32 1-15/16 6 11/16 16NS-2A 23/64 9/32 .450 .454 19

8、/64 13/64 7/16 7/16 7/8 1-3/32 1-31/32 7 3/4 16UNF-2A 11/32 27/64 .514 .518 5/16 13/64 7/16 7/16 7/8 1-3/32 2 8 15/16 16UN-2A 23/64 1/2 .641 .645 11/32 15/64 29/64 29/64 1-1/8 1-1/4 2-1/4 9 1-1/16 16UN-2A 23/64 21/32 .766 .770 11/32 13/64 29/64 29/64 1-1/4 1-1/4 2-3/8 10 1-3/16 16UN-2A 23/64 23/32 .

9、891 .895 11/32 13/64 29/64 29/64 1-3/8 1-5/16 2-7/16 11 1-5/16 16UN-2A 23/64 7/8 1.016 1.020 13/32 13/64 29/64 29/64 1-1/2 1-5/16 2-7/16 12 1-5/8 16UN-2A 7/16 1-3/32 1.270 1.274 13/32 13/64 35/64 35/64 2 1-1/2 2-7/8 13 1-7/8 16UN-2A 15/32 1-11/32 1.520 1.524 15/32 13/64 9/16 9/16 2-1/4 1-1/2 2-15/16

10、 1/ Dimensions are in inches. 2/ This illustration is for identification and is not intended to restrict designs or shapes not dimensioned. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39201G 4 REQUIREMENTS: Dimensions and configuration: See fig

11、ure 1. Tolerances: Unless otherwise specified, decimals .005, fractions 1/64, degrees 2. Threads: The threads shall be in accordance with FED-STD-H28. Nipples: See table I. Material: Code Material C Steel bar, type AISI-C-1112, C-1113, C-1117, C-1118 or C-1137 in accordance with SAE-AIR4127 F Alloy

12、Steel bar in accordance with SAE AIR4127, or type 4130 SAE AMS6370 or SAE AMS-S-6758 or type 4140 SAE AMS6349 or SAE AMS6382. S Corrosion resistant steel in accordance with SAE AMS5659, SAE AMS5862, or, alloy 15-5 PH in accordance with ASTM A564/A564M type XM-12 or UNS S15500, or SAE AMS5665 Chemica

13、l finish: Code Chemical finish: C Carbon steel: Cadmium in accordance with SAE AMS-QQ-P-416, type II, class 3, 200 inches to 300 inches (5.08 m to 7.62 m) thick. F Alloy steel: Cadmium in accordance with SAE AMS-QQ-P-416, type II, class 3, 200 inches to 300 inches (5.08 m to 7.62 m) thick. S Corrosi

14、on resistant steel: Passivate in accordance with SAE AMS2700, type 6 or 7. Z Steel, alternative chem finish: ASTM B633, type VI, FeZn 25. Part or Identifying Number (PIN) example: (PIN covers the complete item with nuts and sleeves.) MS 27612 -8 C Z If finish code same as Material code, then use onl

15、y one code. Material code Dash size Specification number MS prefix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39201G 5 Guidance on use of alternative parts with less hazardous or non-hazardous materials. This specification provides an alternat

16、e material, corrosion resistant steel, and Zinc finish via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function requirements of their application. Changes from previous issue. The margins of this specification are marked with vertical lines to

17、 indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content i

18、rrespective of the marginal notations and relationship to the last previous issue. Referenced documents. This document references the following: FED-STD-H28 ASTM A564/A564M ASTM B633 SAE-AIR4127 SAE AMS5659 MS39210 SAE AMS5665 SAE AMS5862 SAE AMS6370 SAE AMS-S-6758 SAE AMS6349 SAE AMS6382 SAE AMS270

19、0 SAE AMS-QQ-P-416 MS39212 CONCLUDING MATERIAL Custodians: Preparing activity: Army AT DLA - CC Navy-AS DLA - CC (Project 4730-2012-037) Review activities: Army-AR Navy-MC, SA NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-