DLA MS500083 REV E-2006 HOSE ASSEMBLY NONMETALLIC HYDRAULIC AND PNEUMATIC HIGH PRESSURE FEMALE 37 DEGREES FLARED TUBE《橡胶软管装配高液压 37度气动阴扩口管》.pdf

1、 INCH-POUNDMS500083E 17 May 2006 SUPERSEDING MS500083D 16 August 2002 DETAIL SPECIFICATION SHEET HOSE ASSEMBLY, NONMETALLIC: HYDRAULIC AND PNEUMATIC, HIGH PRESSURE, FEMALE 37 FLARED TUBE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirem

2、ents for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-13531. NOTES: 1. All undimensioned pictorial representations are for reference purposes only. 2. Metric equivalents are given for information only. 3. Dimension “L” is the defined length of the hose

3、 assembly. 4. Hose assemblies shall be specified in the following length increments: Under 24 inches (0.61 m) inch (12.70 mm)increments. 24 to 36 inches (0.61 to 0.91 m) - 1-inch (25.40 mm) increments. Over 36 inches (0.91 m)- in not less than 2-inch (50.80 mm) increments. 5. Tolerances: 1/8 inch (.

4、125 inch) (38.10 mm) for length under 24 inches (0.61 m). 1/4 inch (.250 inch) (76.20 mm) for the length from 24 to 36 inches (0.61 to 0.91 m). 1% for length over 36 inches (0.91 m). FIGURE 1. General configuration. AMSC N/A FSC 4720Provided by IHSNot for ResaleNo reproduction or networking permitte

5、d without license from IHS-,-,-MS500083E 2 TABLE I. Hose and fitting thread sizes.Hose OD reference Dash number Hose ID reference Class A Class B Permanent fittings Reuseable fittings Inches mm Inches mm Inches mm Fitting thread reference 3 4 6 8 10 12 16 20 24 32 33 34 35 36 37 38 39 40 41 42 .187

6、.250 .375 .500 .635 .750 1.000 1.250 1.500 2.000 5.0 6.5 9.5 12.5 15.9 19.0 25.5 32.0 38.0 51.0 .625 .687 .843 .968 1.093 1.250 1.562 2.000 2.250 2.750 15.9 17.5 21.4 24.6 27.8 31.8 39.7 51.0 57.1 70.0 .535 .593 .754 .874 1.008 1.156 1.500 1.867 2.148 2.648 13.6 15.0 19.0 22.2 25.6 29.4 38.1 47.4 54

7、.5 67.3 3/8-24 7/16-20 9/16-18 3/4-16 7/8-14 1-1/16-121-5/16-121-5/8-12 1-7/8-12 2-1/2-12 REQUIREMENTS Design and configuration: See figure 1 and table I. Hose material: Type II or III, class A or B. Hose and fittings shall be in accordance with MIL-DTL-13531. Fittings: Dimensions in accordance with

8、 SAE-J516 female 37, flared type, swivel. Fitting material and finish shall be in accordance with MIL-DTL-13531 and designated as follows: A - Steel - cadmium plated S - Stainless steel. Z - Steel - zinc plated. (Zinc plating is not for use in aircraft). Provided by IHSNot for ResaleNo reproduction

9、or networking permitted without license from IHS-,-,-MS500083E 3 Part or Identifying Number (PIN). The PIN is to be used for hose assemblies acquired to this specification. Example is shown below: MS500083 X XX XXX XPrefix for all PINs Fitting material Dash number from table I. (Do not include the “

10、dash” . Use a leading zero for single digit dash numbers, ie. 03 for -3, etc.) Length of hose assembly in inches. (Always use 3 digits. Use leading zeros as required). Fractional length in eighths of an inch. (0 through 7) Changes from previous issue: The margins of this specification are marked wit

11、h asterisks to indicate where changes from the previous issue were made. This was done as a convenience only and the government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the en

12、tire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-DTL-13531, this document references the following: SAE-J516 CONCLUDING MATERIAL Custodians: Preparing activity:Army - AT DLA - CC Navy - SH Air Force - 99 (Projec

13、t 4720-2005-010) DLA - CC Review activities: Army - AR, AV, CR4, MI Navy - AS, MC, SA, Air Force - 11, 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-