DLA MS52103 REV F-2010 HOSE ASSEMBLY NONMETALLIC FUEL AND OIL MEDIUM PRESSURE FLARED TUBE.pdf

1、 MS52103F 15 January 2010 SUPERSEDING MS52103E 1 June 1999 DETAIL SPECIFICATION SHEET HOSE ASSEMBLY, NONMETALLIC: FUEL AND OIL, MEDIUM PRESSURE, FLARED TUBE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product

2、 described herein shall consist of this specification sheet and MIL-DTL-13444. NOTES: 1. All undimensioned pictorial representations are for reference purposes only. 2. Dimension “L” is the defined length of the hose assembly. 3. Hose assemblies shall be specified in the following length increments:

3、 a. Under 24 inches - 1/2 (.500) inch increments (under 60.96 cm - 12.70 mm increments). b. 24 to 36 inches - 1 inch increments (60.96 to 91.44 cm - 25.40 mm increments). c. Over 36 inches - in not less than 2 inch increments (91.44 cm in not less than mm increments). 4. Tolerances shall be as speci

4、fied in the following: a. 1/8 (.125) inch for length under 18 inches (3.18 mm for lengths under 457 mm). b. 1/4 (.250) inch for lengths from 18 to 36 inches (6.35 mm for lengths from 457 to 914 mm). c. 1/2 (.500) inch for lengths from 36 to 50 inches (12.70 mm for lengths from 914 to 1270 mm). d. 1%

5、 for lengths over 50 inches (1% for lengths over 1270 mm). FIGURE 1. General configuration. AMSC N/A FSC 4720 INCH - POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS52103F 2 TABLE I. Hose and fitting thread sizes. 1/ 2/ Dash number Hose ID re

6、f. Hose OD ref. Fitting thread ref -04 3/16 inch .484 (12.29) 7/16 - 20UNF-2B .188 inch 4.78 mm -05 1/4 inch .547 (13.89) 1/2 - 20UNF-2B .250 inch 6.35 mm -06 5/16 inch .609 (15.47) 9/16 - 18UNF-2B .313 inch 7.95 mm -08 13/32 inch .734 (18.64) 3/4 - 16UNF-2B .406 inch 10.31 mm -10 1/2 inch .828 (21.

7、03) 7/8 - 14UNF-2B .500 inch 12.70 mm -12 5/8 inch .953 (24.21) 1-1/16 - 12UN-2B .625 inch 15.88 mm -16 7/8 inch 1.203 (30.56) 1-5/16 - 12UN-2B .875 inch 22.23 mm -20 1-1/8 inch 1.484 (37.69) 1-5/8 - 12UN-2B 1.125 inch 28.58 mm -24 1-3/8 inch 1.722 (43.74) 1-7/8 - 12UN-2B 1.375 inch 34.93 mm -32 1-1

8、3/16 inch 2.143 (54.43) 2-1/2 - 12UN-2B 1.813 inch 46.05 mm 1/ Dimensions are in inches 2/ Metric equivalents are given for information only. REQUIREMENTS Design and configuration: See figure 1 and table I. Hose material: The hose used in these assemblies shall be in accordance with MIL-DTL-13444, t

9、ype III. Fittings: Fitting shall be in accordance with SAE J516 female 37 flare. Finish shall meet the salt spray requirements of MIL-DTL-13444. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS52103F 3 Part or Identifying Number (PIN). The PINs to

10、be used for hose assemblies acquired to this specification are created as shown in the example below. MS52103 C -08 016 4 R Fitting material/finish designators: A - Carbon steel, cadmium plated. B - Brass. C - Carbon steel S - Corrosion resistant steel. Z - Carbon steel, zinc plated. Cadmium is not

11、recommended. To the users of this document, it is recommended that the use of carbon steel material with cadmium plating be used only when other materials and finishes specified in this document cannot meet performance requirements. Some existing MS PINs do not completely fit the above layout, but t

12、hey should continue to be used without change. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced document. In addition to MIL-DTL-13444, this document references SAE J516.

13、 Fractional length in eighths of an inch (0 thru 7). Length of hose assembly in inches. (Always use 3 digits. Use leading zeros as required.) Dash number from table I. Use a leading zero for single digit numbers, i.e. 03 for 3, etc. Fitting material/finish designator MS prefix and specification shee

14、t number Type of fitting. R = Reusable, P = Permanent Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS52103F 4 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - YD Air Force - 99 (Project 4720-2009-015) DLA - CC Review a

15、ctivities: Army - AR, AV, MI Navy - AS, MC, SH NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-