DLA QQ-C-450A (2)-2002 COPPER-ALUMINUM ALLOY (ALUMINUM BRONZE) PLATE SHEET STRIP AND BAR (COPPER ALLOY NUMBERS 606 610 613 614 AND 630).pdf

1、 INCH-POUND QQ-C-450A AMENDMENT 26 August 2002 SUPERSEDINGINT. AMENDMENT 1 21 January 1981 FEDERAL SPECIFICATION COPPER-ALUMINUM ALLOY (ALUMINUM BRONZE) PLATE, SHEET, STRIP, AND BAR (COPPER ALLOY NUMBERS 606, 610, 613, 614, AND 630) The General Services Administration has authorized the use of this

2、amendment, which forms a part of QQ-C-450A, dated 17 September 1974 by all federal agencies. PAGE 1 2.1: Delete. PAGE 2 2.2: Delete and Substitute: “2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the i

3、ssues of the documents which are DoD adopted are those listed in the issue of the D0DISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the D0DISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR QUALITY CONTROL A

4、SQC Z1.4 - Sampling Procedures and Tables for Inspection by Attributes (Application for copies should be addressed to the American Society for Quality Control, P.O. Box 3005, 611 E. Wisconsin Avenue, Milwaukee, WI 53201-4606.) AMERICAN SOCIETY FOR TESTING AND MATERIALS ASTM B154 - Mercurous Nitrate

5、Test for Copper and Copper Alloys ASTM E8 - Standard Test Methods for Tension Testing of Metallic Materials ASTM E1282 - Standard Guide for Specifying the Chemical Compositions and Selecting Sampling Practices and Quantitative Analysis Methods for Metals, Ores, and Related Materials (Application for

6、 copies should be addressed to the American Society for Testing and Material, 100 Barr Harbor Dr., West Conshohocken, PA 19428.)”. AMSC N/A 1 of 3 FSC 9530 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking per

7、mitted without license from IHS-,-,-QQ-C-450A AMENDMENT 2 SAE INTERNATIONAL (SAE) AMS-STD-185 - Identification Marking of Copper and Copper Base Alloy Mill Products AMS2221 - Tolerances, Copper and Copper Alloy Bars and Rods AMS2222 - Tolerances, Copper and Copper Alloy Sheet, Strip, and Plate (Appl

8、ication for copies should be addressed to SAE International, 400 Commonwealth Drive, Warrendale, PA 15096.) PAGE 6 3.6: Delete and substitute: “3.6 Dimensional tolerances. Dimensional tolerances shall be in accordance with the applicable AMS2221 or AMS2222.” 3.7: Delete “Fed. Std. No. 185” and subst

9、itute “AMS-STD-185”. 4.1: Delete and substitute: “4.1 Responsibility for inspection. Unless otherwise specified in the contract, the contractor is responsible for the performance of all inspection requirements as specified herein. Except, as otherwise specified in the contract, the contractor may us

10、e his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assu

11、re supplies and services conform to prescribed requirements. 4.1.1 Certification of quality compliance. A certificates of quality compliance shall be prepared for each lot of material offered for acceptance (see 6.2.1). The certificate shall include actual data of specified chemical and mechanical t

12、ests. Qualitative results of nondestructive tests and other inspections or tests shall be recorded on the certificate. The certificate shall also state that each lot has been sampled, tested, and inspected accordance with the specification and meets all specification requirements. The certificate sh

13、all be signed by a responsible representative of the contractor.” PAGE 7 4.3.4.2, third line: Delete “MIL-STD-105, inspection level II with an acceptable quality level (AQL) of 1.5 percent defective”and substitute “ASQC Z1.4. Lot acceptance criteria shall be based on a single sampling plan with a ze

14、ro acceptance number.” PAGE 8 4.4.2: Delete 4.5.2.1, second line: Delete “by method 111 or method 112 of Fed. Test Std No. 151” and substitute with “ASTM E1282”. PAGE 9 4.6.1: Delete: 4.7: Delete. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-QQ-

15、C-450A AMENDMENT 2 5: Delete Section 5 entirely and substitute: “5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of material is to be performed by DoD personnel, these personnel need to c

16、ontact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Departments System Command. Packaging data retrie

17、val is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity.” PAGE 10 6.2g & 6.2h: Delete. 6.3: Delete. Custodians: Preparing Activity: Army - AR DLA - IS Navy - SH (Project 9530-0569) Review Activities: Army MI Navy - AS 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-