1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Redraw. Sheet 5, table I, correct INL test limit. Update drawing to current requirements. drw 10-01-15 Charles F. Saffle REV SHET REV A A A A A SHEET 15 16 17 18 19 REV STATUS REV A A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 1
2、1 12 13 14 PMIC N/A PREPARED BY Rick Officer DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Rajesh Pithadia COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Raymond Monnin MICROCIRCUIT, DIGITAL-LINEAR, 14-BIT,
3、8 MSPS, ANALOG-TO-DIGITAL CONVERTER, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 01-01-16 AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-00511 SHEET 1 OF 19 DSCC FORM 2233 APR 97 5962-E125-10 Provided by IHSNot for ResaleNo reproduction or networking per
4、mitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00511 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents three product assurance class levels consisting of space application
5、(device class V), high reliability (device classes M and Q), and nontraditional performance environment (device class N). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA
6、) levels are reflected in the PIN. For device class N, the user is cautioned to assure that the device is appropriate for the application environment. 1.2 PIN. The PIN is as shown in the following example: 5962 - 00511 01 N X D Federal stock class designator RHA designator (see 1.2.1) Device type (s
7、ee 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes N, Q, and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marke
8、d devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type. The device type identifies the circuit function as follows: Device type Generic number Circuit function 01 THS1408 14-bit, 8
9、 MSPS, analog-to-digital converter with an internal reference 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-8
10、83 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A N Certification and qualification to MIL-PRF-38535 with a nontraditional performance environment 1/ Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline. The case outline is as design
11、ated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 48 Plastic quad flatpack 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes N, Q, and V or MIL-PRF-38535, appendix A for device class M. _ 1/ Items wh
12、ich have been subjected to and passed all applicable requirements of this specification including qualification testing, screening testing, and TCI/QCI inspections, and are encapsulated in plastic. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAN
13、DARD MICROCIRCUIT DRAWING SIZE A 5962-00511 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (AVDDto AGND) 4 V Supply voltage (DVDDto DGND) . 4 V Reference input voltage range (VBG) . -0.3 V to AVD
14、D+0.3 V Analog input voltage range . -0.3 V to AVDD+0.3 V Digital input voltage range . -0.3 V to DVDD+0.3 V Power dissipation (PD) . 360 mW Storage temperature range . -65C to +150C Lead temperature 1.6 mm (1/16 inch) from case for 10 seconds +260C Thermal resistance, junction-to-case (JC) 0.79C/W
15、Thermal resistance, junction-to-ambient (JA) . 28.8C/W 1.4 Recommended operating conditions. Supply voltage range (AVDD, DVDD) 3.0 V to 3.6 V High level digital input (VIH) . 2 V minimum Low level digital input (VIL) 0.8 V maximum Load capacitance (CL) . 15 pF Clock frequency range (fCLK) . 8 MHz Cl
16、ock duty cycle 45 % to 55 % Output disable (tdis) . 10 ns is a typical value Write pulse duration high (twH(WE) . 15 ns minimum Ambient operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standard
17、s, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. D
18、EPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of thes
19、e documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited he
20、rein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum le
21、vels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00511 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR
22、97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes N, Q, and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the fo
23、rm, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dim
24、ensions shall be as specified in MIL-PRF-38535 and herein for device classes N, Q, and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall
25、be as specified on figure 2. 3.2.3 Block diagram. The block diagram shall be as specified on figure 3. 3.2.4 Timing diagrams. The timing diagrams shall be as specified on figure 4. 3.2.5 Principles of operation. The principles of operation shall be as specified on figure 5. 3.3 Electrical performanc
26、e characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements.
27、The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of
28、the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes N, Q, and V shall be in accordance with MIL-PRF-38535.
29、 Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes N, Q, and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL
30、-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes N, Q, and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall b
31、e required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device
32、classes N, Q, and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes N, Q, and V in MIL-PRF-38535 or for device class M in MIL-PRF
33、-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that a
34、ffects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of
35、 the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 81 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MI
36、CROCIRCUIT DRAWING SIZE A 5962-00511 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA+125C Group A subgroups Device type Limits Unit unless otherwise specified Mi
37、n Max Power supply section Analog supply current IDDAAVDD= 3.6 V 1, 2, 3 01 90 mA Digital supply current IDDDDVDD= 3.6 V 1, 2, 3 01 10 mA DC characteristics section Differential nonlinearity DNL 1, 2, 3 01 1 LSB Integral nonlinearity INL 8 MSPS 1, 2, 3 01 10.5 LSB 3 MSPS 4 Offset error OE +INPUT = -
38、INPUT,PGA = 0 dB 1, 2, 3 01 0.3 %FSR Gain error GE PGA = 0 dB 1, 2, 3 01 1.75 %FSR AC characteristics section Effective number of bits ENOB 4, 5, 6 01 11.2 Bits Signal-to-noise ratio SNR fIN= 1 MHz 4, 5, 6 01 70 dB Signal-to-noise + distortion SINAD fIN= 1 MHz 4, 5, 6 01 69 dB Spurious free dynamic
39、range SFDR fIN= 1 MHz 4, 5, 6 01 71 dB Reference voltage section Bandgap voltage, internal mode VBG 1, 2, 3 01 1.425 1.575 V Analog inputs section Positive analog input +IN 1, 2, 3 01 0 AVDDV Negative analog input -IN 1, 2, 3 01 0 AVDDV Analog input voltage difference AIN= +IN - -IN, VREF= +REF - -R
40、EF 1, 2, 3 01 -VREF+VREFV PGA range 1, 2, 3 01 0 7 dB PGA gain error 1, 2, 3 01 0.25 dB See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00511 DEFENSE SUPPLY CENTER COLUMBUS COLU
41、MBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions 1/ -55C TA+125C Group A subgroups Device type Limits Unit unless otherwise specified Min Max Digital inputs section High level digital input VIH1,
42、2, 3 01 2 V Low-level digital input VIL1, 2, 3 01 0.8 V Input current IIN1, 2, 3 01 1 A Digital outputs section High-level digital output VOHIOH= 50 A 1, 2, 3 01 2.6 V Low-level digital output VOLIOL= 50 A 1, 2, 3 01 0.4 V Output current, high impedance IOZ1, 2, 3 01 10 A Clock timing (CS low) secti
43、on Clock frequency fCLK 9, 10, 11 01 8 MHz Output delay time td 9, 10, 11 01 25 ns 1/ Unless otherwise specified, supply voltage range (AVDD, DVDD) will equal 3.3 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A
44、 5962-00511 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 Case X FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00511 DEFENSE
45、 SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 Case X Dimensions Symbol Millimeters Min Max A 1.20 A1 0.95 1.05 A2 0.25 - A3 0.05 0.15 b 0.17 0.27 C 0.13 - D 8.80 9.20 D1 6.80 7.20 D2 5.50 - E 8.80 9.20 E1 6.80 7.20 E2 5.50 - e 0.50 - L1 0.45 0.75 NO
46、TES: 1. The package thermal performance may be enhanced by bonding the thermal pad to an thermal plate. This pad is electrically and thermally connected to the backside of the die and possible selected leads. 2. Body dimensions do not include mold flash or protrusion. FIGURE 1. Case outline - contin
47、ued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00511 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 9 DSCC FORM 2234 APR 97 Device type 01 Device type 01 Case outline X
48、Case outline X Terminal number Terminal symbol Terminal number Terminal symbol 1 -IN 25 DGND 2 AVDD26 DVDD3 VBG 27 D2 4 CML 28 D1 5 +REF 29 D0 6 -REF 30 DVDD7 AGND 31 DVDD8 AGND 32 CLK 9 DGND 33 DGND 10 OV 34 DGND 11 D13 35 OE 12 D12 36 WR 13 D11 37 CS 14 DVDD38 NC 15 DGND 39 NC 16 D10 40 A1 17 D9 41 A0 18 D8 42 DVDD19 D7 43 AVDD20 DVDD44 AGND 21 D6 45 AGND 22 D5 46 AGND 23 D4 47 AVDD24 D3 48 +IN NC = No connection FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo rep
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1