DLA SMD-5962-00515 REV D-2012 MICROCIRCUIT LINEAR SINGLE ULTRAFAST COMPARATOR MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. - gt 02-04-24 R. MONNIN B Add radiation hardness assurance requirements. - rrp 02-07-29 R. MONNIN C Five year review requirement. - ro 07-10-02 R. HEBER D Add device type 02 tested at low dose rate

2、. Make change to paragraphs 1.2.2 and 1.5. Make changes to footnotes 1/ and 2/ as specified under Table I. Make change to paragraph 4.4.4.1. -rrp 12-05-31 C. SAFFLE REV SHEET REV SHEET REV STATUS REV D D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Rajesh

3、Pithadia DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Rajesh Pithadia APPROVED BY Raymond Monnin MICROCIRCUIT, LINEAR, SINGLE,

4、ULTRAFAST COMPARATOR, MONOLITHIC SILICON DRAWING APPROVAL DATE 00-04-06 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-00515 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E360-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT

5、 DRAWING SIZE A 5962-00515 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A ch

6、oice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 R 00515 01 V H A Federal stock c

7、lass designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with t

8、he appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Devic

9、e type Generic number Circuit function 01 AD8561A Ultrafast single supply comparator 02 AD8561A Ultrafast single supply comparator 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements docume

10、ntation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and

11、 as follows: Outline letter Descriptive designator Terminals Package style H GDFP1-F10 or CDFP2-F10 10 Flat pack P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provi

12、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00515 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Total analog supply voltage . +

13、14 V Digital supply voltage . +14 V Analog positive supply-digital positive supply -600 mV Input voltage 7 V Differential input voltage 8 V Output short circuit duration to GND Indefinite Storage temperature range -65C to +150C Operating temperature range -55C to +125C Junction temperature range . -

14、65C to +150C Lead temperature range (soldering, 10 seconds) +300C Power dissipation (PD) 500 mW Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case H . 180C/W Case P . 148C/W 1.4 Recommended operating conditions. 2/ 3/ 6/ Single supply voltag

15、e operation . +3.0 V to +5.0 V Dual supply voltage operation . 5 V Ambient operating temperature (TA) . -55C to +125C 1.5 Radiation features: Device type 01: Maximum total dose available (dose rate = 50 300 rads(Si)/s) . 100 krads(Si) 2/ Device type 02: Maximum total dose available (dose rate 10 mra

16、ds(Si)/s) 50 krads(Si) 3/ 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the

17、 solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. _ 1/ S

18、tresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Device type 01, may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects. Radiat

19、ion end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883, method 1019, condition A. 3/ For device type 02, radiation end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883, method 1019, condition

20、D. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00515 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of S

21、tandard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of preced

22、ence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirem

23、ents. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein

24、. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF

25、-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Radiation exposure cir

26、cuit. The radiation exposure circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing and acquiring activity upon request. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise speci

27、fied herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA

28、. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN is not feasible due to space limitations, the manufacturer

29、 has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1

30、 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certifi

31、cate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK

32、-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device cla

33、ss M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this d

34、rawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00515 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Te

35、st Symbol Conditions 1/ 2/ -55C TA +125C unless otherwise specified Group A subgroups Devicetype Limits Unit Min Max V+ = +5 V, V- = VGND= 0 V section Input offset voltage 3/ VOS1 All 7 mV 2, 3 8 Input bias current 3/ IBVCM= 0 V 1 All -6 A 2, 3 -7 Input offset current 3/ IOSVCM= 0 V 1, 2, 3 All +4 A

36、 Input voltage range 3/ IVRV+ = 5 V, V- = 0 V 1 All 0 +3 V Common mode rejection 3/ ratio CMRR VCM= IVR1 All 65 dB Logic “1“ input voltage 3/ VIH1 All 2 V Logic “0“ input voltage 3/ VIL1 All 0.8 V Logic “1“ current 3/ IIHVIH= 3 V 1 All -1 A Logic “0“ input current 3/ IILVIL= 0.3 V 1 All -4 A Logic “

37、1“ output voltage 3/ VOHIOH= -50 A, VIN 250 mV, 1 All 3.5 V IOH= -3.2 mA, VIN 250 mV 1 2.4 Logic “0“ output voltage 3/ VOLIOL= 3.2 mA, VIN 250 mV 1 All 0.4 V Power supply rejection 3/ ratio PSRR V+ = 4.5 V to +5.5 V 1, 2, 3 All 50 dB Positive supply current 3/ I+ 1 All 6.0 mA 2, 3 7.5 Ground supply

38、current 3/ IGNDVOUT= 0 V, RL= 1 All 3.3 mA 2, 3 3.8 Analog supply current 3/ I- 1 All 4.5 mA 2, 3 5.5 Propagation delay 3/ tP200 mV step with 100 mV overdrive 9 All 9.8 ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,

39、-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00515 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ 2/ -55C TA +125C unless otherwise specified Group A subgroups Devicetyp

40、e Limits Unit Min Max V+ = +5 V, V- = -5 V, VGND = 0 V section Input offset voltage VOS1 All 7 mV 2, 3 8 M,D,P,L,R 1 01 10 M,D,P,L 1 02 10 Input bias current IBVCM= 0 V 1 All -6 A 2, 3 -7 M,D,P,L,R 1 01 -7 M,D,P,L 1 02 -7 Input offset current IOSVCM= 0 V 1, 2, 3 All +4 A M,D,P,L,R 1 01 +4 M,D,P,L 1

41、02 +4 Input voltage range 3/ IVR1 All -5.0 +3.0 V Common mode rejection 3/ ratio CMRR VCM= IVR1 All 65 dB Logic “1“ input voltage 3/ VIH1 All 2.0 V Logic “0“ input voltage 3/ VIL1 All 0.8 V Logic “1“ current 3/ IIHVIH= 3 V 1 All -1 20 A Logic “0“ input current 3/ IILVIL= 0.3 V 1 All -4 20 A Logic “1

42、“ output voltage 3/ VOHIOH= -3.2 mA, VIN 250 mV 1 All 2.6 V Logic “0“ output voltage 3/ VOLIOL= 3.2 mA, VIN 250 mV 1 All 0.3 V Power supply rejection 3/ ratio PSRR VS= 4.5 V to 5.5 V 1 All 55 dB See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted witho

43、ut license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00515 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ 2/ -55C TA +125C unless otherwise specified Grou

44、p A subgroups Device type Limits Unit Min Max V+ = +5 V, V- = -5 V, VGND = 0 V section continued. Positive supply current I+ 1 All 6.5 mA 2, 3 7.5 M,D,P,L,R 1 01 7.0 M,D,P,L 1 02 7.0 Ground supply current IGNDVOUT= 0 V, RL= 1 All 3.3 mA 2, 3 3.8 M,D,P,L,R 1 01 3.5 M,D,P,L 1 02 3.5 Analog supply curr

45、ent I- 1 All 4.5 mA 2, 3 5.5 M,D,P,L,R 1 01 5.0 M,D,P,L 1 02 5.0 Propagation delay 3/ tP200 mV step with 100 mV overdrive 9 All 9.8 ns V+ = 3 V, V- = VGND= 0 V section Input offset voltage 3/ VOS1 All 7 mV Input bias current 3/ IBVCM= 0 V 1 All -6 A 2, 3 -7 Input voltage range 3/ IVR1 All 0 1.5 V Co

46、mmon mode rejection 3/ ratio CMRR 0.1 V VCM 1.5 V 1 All 60 dB Logic “1“ output 3/ 4/ voltage VOHIOH= -3.2 mA, VIN 250 mV 1 All 1.2 V Logic “0“ output voltage 3/ VOLIOL= 3.2 mA, VIN 250 mV 1 All 0.3 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted

47、without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00515 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ 2/ -55C TA +125C unless otherwise specified

48、 Group A subgroups Device type Limits Unit Min Max V+ = 3 V, V- = VGND= 0 V section continued. Positive supply current 3/ I+ 1 All 4.5 mA 2, 3 5.5 Ground supply current 3/ IGNDVOUT= 0 V, RL= 1 All 2.5 mA 2, 3 3.0 Analog supply current 3/ I- 1 All 3.3 mA 1/ Device type 01 supplied to this drawing has been characterized through all levels P, L, and R of irradiation. Device type 02 supplied to this drawing has been characterized at level L of irradiation. However, dev