DLA SMD-5962-00516 REV D-2012 MICROCIRCUIT LINEAR POSITIVE 5-VOLT ADJUSTABLE PRECISION VOLTAGE REFERENCE MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add case outline H and make change to long term stability test as specified in table I. - ro 01-11-16 R. MONNIN B Add case outlines P and 2. Make changes to 1.2.4, 1.3, and figure 1. - lgt 02-04-22 R. MONNIN C Drawing updated to reflect current r

2、equirements. -rrp 08-10-27 R. HEBER D Add device type 02. Delete radiation exposure circuit. - ro 12-06-06 C. SAFFLE REV SHEET REV SHEET REV STATUS REV D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http

3、:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAJESH PITHADIA APPROVED BY RAYMOND MONNIN MICROCIRCUIT, LINEAR, POSITIVE 5-VOLT ADJUSTABLE PRECISION VOLTAGE REFERENCE, MONOLITHIC SI

4、LICON DRAWING APPROVAL DATE 00-04-05 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-00516 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E331-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00516 DLA LAND

5、 AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead fini

6、shes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 R 00516 01 V G A Federal stock class designator RHA designator (see

7、 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Devi

8、ce class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit funct

9、ion 01 REF05A +5 volt precision voltage reference with adjustable output 02 REF05A +5 volt precision voltage reference with adjustable output 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirem

10、ents documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-S

11、TD-1835 and as follows: Outline letter Descriptive designator Terminals Package style G MACY1-X8 8 Can H GDFP1-F10 or CDFP2-F10 10 Flat pack P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for devic

12、e classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00516 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234

13、 APR 97 1.3 Absolute maximum ratings. 1/ Input voltage (VIN) . 40 V dc Power dissipation (PD) 500 mW Output short circuit duration . Indefinite Storage temperature -65C to +150C Lead temperature (soldering, 60 seconds) +300C Junction temperature (TJ) -65C to +150C Thermal resistance, junction-to-cas

14、e (JC) See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case G . 150C/W Case H . 180C/W Case P . 148C/W Case 2 95C/W 1.4 Recommended operating conditions. Input voltage (VIN) . +15 V Ambient operating temperature range (TA) . -55C to +125C 1.5 Radiation features: Maximum total dose ava

15、ilable (dose rate = 50 300 rads(Si)/s): Device type 01 . 100 krads(Si) 2/ Maximum total dose available (dose rate 10 mrads(Si)/s): Device type 02 . 50 krads(Si) 3/ _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may d

16、egrade performance and affect reliability. 2/ Device type 01 may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects. Radiation end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883, method 1019, conditi

17、on A. 3/ Device type 02 radiation end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883 method 1019, condition D. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A

18、 5962-00516 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein.

19、 Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircu

20、its. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/

21、or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, h

22、owever, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacture

23、rs Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 D

24、esign, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with

25、1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing and acquir

26、ing activity upon request. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating t

27、emperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers P

28、IN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q

29、 and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00516 DLA LAND AND MARITIME

30、COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, ap

31、pendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a

32、manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device c

33、lasses Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, a

34、ppendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any chan

35、ge that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall

36、 be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 59 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitt

37、ed without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00516 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ -55C TA +125C VIN= 15 V Group A subgroups Devic

38、e type Limits Unit unless otherwise specified Min Max Quiescent supply current ISYNo load 1 01, 02 1.4 mA 2,3 2.0 M,D,P,L,R 1 01 1.4 M,D,P,L 02 1.4 Output adjustment range VTRIMRP= 10 k 3/ 1 01, 02 3.0 % Output voltage VOUTIL= 0 mA 1 01, 02 4.985 5.015 V 2,3 4.978 5.022 M,D,P,L,R 1 01 4.975 5.025 M,

39、D,P,L 02 4.975 5.025 Short circuit current IOSVOUT= 0 V 3/ 1 01, 02 +15 +60 mA Sink current IS3/ 1 01, 02 -0.3 mA Load regulation LD reg IL= 0 mA to 10 mA 4/ 1 01, 02 0.01 %/mA M,D,P,L,R 1 01 0.015 M,D,P,L 02 0.015 IL= 0 mA to 8 mA 4/ 2,3 01, 02 0.012 Line regulation LN reg VIN= 8 V to 33 V 4/ 1 01,

40、 02 0.01 %/V 2,3 0.015 M,D,P,L,R 1 01 0.03 M,D,P,L 02 0.03 Load current IL3/ 5/ 1 01, 02 10 mA 2,3 8 Output voltage noise enp-p 0.1 Hz to 10 Hz 4 01, 02 15 VP-POutput voltage temperature coefficient TCVO6/ 8 01, 02 8.5 ppm/C Long term stability VOUT/ t Lot qualification test 7/ 01, 02 100 ppm / 1 kH

41、r See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00516 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical perfor

42、mance characteristics Continued. 1/ Device type 01 supplied to this drawing has been characterized through all levels P, L, and R of irradiation. Device type 02 supplied to this drawing has been characterized to level L of irradiation. However, device type 01, is only tested at the “R” level and dev

43、ice type 02 is only tested at the ”L” level. Pre and Post irradiation values are identical unless otherwise specified in table I. When performing post irradiation electrical measurements for any RHA level, TA= +25C. 2/ Device type 01 may be dose rate sensitive in a space environment and demonstrate

44、enhanced low dose rate effect. Radiation end point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, method 1019, condition A for device type 01 and condition D for device type 02. Device type 02 is tested at low dose rate. 3/ Not tested post irradia

45、tion. 4/ Line and load regulation specifications include the effect of self-heating. 5/ Minimum load current guaranteed by loading regulation test. 6/ TCVO= (VMAX VMIN) / 5 V) x (1 / 180C) x 106where -55C TA +125C. 7/ Each wafer lot is tested for long-term stability at a chip temperature of 76C for

46、168 hours. Maximum percent defective size is 5 and acceptance number is 2 with sample size of 105. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00516 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISIO

47、N LEVEL D SHEET 8 DSCC FORM 2234 APR 97 Device types 01, 02 Case outlines P G (see note 2) H 2 Terminal number Terminal symbol 1 NC NC NC NC 2 VINVINVINNC 3 TEMP TEMP TEMP NC 4 GND GND GND NC 5 TRIM TRIM TRIM VIN6 VOUTVOUTVOUTNC 7 NC NC NC TEMP 8 NC NC NC NC 9 - - NC NC 10 - - NC GND 11 - - - NC 12

48、- - - TRIM 13 - - - NC 14 - - - NC 15 - - - VOUT16 - - - NC 17 - - - NC 18 - - - NC 19 - - - NC 20 - - - NC NOTES: 1. NC = No connection. 2. Case is ground. FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00516 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 9 DSCC FORM 2234 A