DLA SMD-5962-04211 REV A-2011 MICROCIRCUIT DIGITAL ADVANCED CMOS 16-BIT BUS TRANSCEIVER WITH THREE-STATE OUTPUTS MONOLITHIC SILICON.pdf

1、REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update radiation features in section 1.5. Add SEP test table IB and paragraph 4.4.4.2 jak- 11-04-13 David J. Corbett PRELIMINARY DRAFT SHEET REV A A A A A SHEET 15 16 17 18 19 REV STATUS OF SHEETS REV A A A A A A A A A A A A A A SHEET 1 2 3 4 5 6

2、7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Thanh V. Nguyen DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A CHECKED BY Thanh V. Nguyen APPROVED B

3、Y Thomas M. Hess MICROCIRCUIT, DIGITAL, ADVANCED CMOS, 16-BIT BUS TRANSCEIVER WITH THREE-STATE OUTPUTS, MONOLITHIC SILICON DRAWING APPROVAL DATE 04-03-16 REVISION LEVEL A SIZE A CAGE CODE 67268 5962-04211 SHEET 1 OF 19 DSCC FORM 2233 APR 97 5962-E063-11 .Provided by IHSNot for ResaleNo reproduction

4、or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-04211 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliabi

5、lity (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN i

6、s as shown in the following example: 5962 F 04211 01 V X A Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked

7、 devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device t

8、ype(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54AC16245 16-bit bus transceiver with three-state outputs 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follo

9、ws: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outli

10、ne(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 48 Flat pack 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided b

11、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-04211 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.

12、5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to VCC + 0.5 V dc DC output voltage range (VOUT) . -0.5 V dc to VCC+ 0.5 V dc DC input clamp diode current (IIK) . 20 mA DC output clamp diode current (IOK) . 20 mA DC output current (IOUT) . 25 mA DC VCCor GND current (per output pin) . 200

13、 mA Maximum power dissipation (PD) 500 mW Storage temperature range (TSTG) . -65C to +150C Lead temperature (soldering, 10 seconds) +260C Thermal resistance, junction-to-case (JC) . 22C/W Junction temperature (TJ) 175C 4/ 1.4 Recommended operating conditions. 2/ 3/ 5/ Supply voltage range (VCC) +2.0

14、 V dc to +6.0 V dc Input voltage range (VIN) 0.0 V dc to VCCOutput voltage range (VOUT) . 0.0 V dc to VCCInput rise or fall time rate (VINfrom 30% to 70% of VCC) (t/v): VCC= 3.0 V, 45 V, and 5.5 V 0 to 8 ns/V Case operating temperature range (TC) . -55C to +125C 1.5 Radiation features. Maximum total

15、 dose available (dose rate = 50 300 rads(Si)/s) 300 krads (Si) Single event phenomenon (SEP): effective LET, no SEL (see 4.4.4.2) 93 MeV-cm2/mg 6/effective LET, no SEU (see 4.4.4.2) . 93 MeV-cm2/mg 6/ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended op

16、eration at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. 4/ Maximum junction

17、 temperature shall not be exceeded except for allowable short duration burn-in screening conditions in accordance with method 5004 of MIL-STD-883. 5/ Operation from 2.0 V dc to 3.0 V dc is provided for compatibility with data retention and battery back-up systems. Data retention implies no input tra

18、nsition and no stored data loss with the following conditions: VIH 70% of VCC, VIL 30% of VCC, VOH 70% of VCCat -20 A, VOL 30% of VCCat 20 A. 6/ These limits were obtained during technology characterization and qualification, and are guaranteed by design or process, but not production tested unless

19、specified by the customer through the purchase order or contract. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-04211 REVISION LEVEL A SHEET 4 DSCC FORM 2234

20、APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or co

21、ntract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HAN

22、DBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 1

23、9111-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents cited in the solicitation or contract. JEDEC SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JESD-20 - Standard for

24、 Description of 54/74ACXXXX and 54/74ACTXXXX Advanced High-Speed CMOS Devices. (Copies of these documents are available online at http:/www.jedec.org or from JEDEC Solid State Technology Association, 3103 North 10th Street, Suite 240S, Arlington, VA 22201.) ASTM INTERNATIONAL (ASTM) ASTM F1192- Stan

25、dard Guide for the Measurement of Single Event Phenomena (SEP) Induced by Heavy Ion Irradiation of Semiconductor Devices. (Copies of this document is available online at http:/www.astm.org/ or from ASTM International, P. O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959). (Non-Gov

26、ernment standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents may also be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of thi

27、s drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classe

28、s Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M sh

29、all be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-

30、38535, appendix A and herein for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-04211 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 3.2.1 Case

31、 outline. The case outline shall be in accordance with 1.2.4 and figure 1 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Truth table. The truth table shall be as specified on figure 3. 3.2.4 Logic diagram. The logic diagram shall be as specified

32、 on figure 4. 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. 3.2.6 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the manufacturer under document revision level control and shall be made avail

33、able to the preparing or acquiring activity upon request. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and post irradiation parameter limits are as specified in table IA and shall apply

34、over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In

35、 addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked

36、. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-3853

37、5. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see

38、 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source

39、of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as requ

40、ired for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of pr

41、oduct (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritime s agent, and the acquiring activity retain the option to review the

42、 manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 37 (see MIL

43、-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-04211 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance ch

44、aracteristics. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ 3/ -55C TC +125C +3.0 V VCC +5.5 V unless otherwise specified Device type and device class VCCGroup A subgroups Limits 4/ Unit Min Max High level input voltage VIH5/ All All 3.0 V 1, 2, 3 2.1 V 4.5 V 3.15 5.5 V 3.85 Low lev

45、el input voltage VIL5/ All All 3.0 V 1, 2, 3 0.9 V 4.5 V 1.35 5.5 V 1.65 High level output voltage 3006 VOHFor all inputs affecting output under test VIN= VIHor VILFor all other inputs VIN= VCCor GND IOH= -50 A All All 3.0 V 1, 2, 3 2.9 V 4.5 V 1, 2, 3 4.4 5.5 V 1, 2, 3 5.4 IOH= -12 mA 3.0 V 1 2.56

46、2, 3 2.46 IOH= -24 mA 4.5 V 1 3.86 2, 3 3.76 5.5 V 1 4.86 2, 3 4.76 IOH= -50 mA 6/ 5.5 V 1, 2, 3 3.85 Low level output voltage 3007 VOLFor all inputs affecting output under test VIN= VIHor VILFor all other inputs VIN= VCCor GND IOL= 50 A All All 3.0 V 1, 2, 3 0.1 V 4.5 V 1, 2, 3 0.1 5.5 V 1, 2, 3 0.

47、1 IOL= 12 mA 3.0 V 1 0.36 2, 3 0.44 IOL= 24 mA 4.5 V 1 0.36 2, 3 0.44 5.5 V 1 0.36 2, 3 0.44 IOL= 50 mA 6/ 5.5 V 1, 2, 3 1.65 Positive input clamp voltage 3022 VIC+For input under test, IIN= 1.0 mA All Q, V 0.0 V 1 0.4 1.5 V Negative input clamp voltage 3022 VIC-For input under test, IIN= -1.0 mA Al

48、l Q, V Open 1 -0.4 -1.5 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-04211 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 TABLE IA. Electrical performance characteristics - Continued. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ 3/ -55C TC +125C +3.0 V VCC +5.5 V unless otherwise specified Device type and device class VCCGroup A subgroups Limi