DLA SMD-5962-05241 REV B-2013 MICROCIRCUIT HYBRID LINEAR 12 VOLT DUAL CHANNEL DC DC CONVERTER.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Table II, add note to Group C end-point test parameters. Update boilerplate paragraphs. -gz 11-02-10 Charles F. Saffle B Add case outline Y. gc 13-06-20 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV B B B B B B B B B B B OF SHEETS SHEET 1

2、2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Raymond Monnin MICROCIRCUIT, HYBRID, LINEAR, 12 VOLT, DUAL

3、CHANNEL, DC/DC CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 06-06-12 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-05241 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E421-13Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

4、,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-05241 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and

5、lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 05241 01 K X X Federal RHA Device Device Case Lea

6、d stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with t

7、he appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type. The device type identify the circuit function as follows: Device type Generic number Circuit function 01 LS2812D DC/DC converter, 30 W, 12 V outputs 1.2.3 Device class designator. This device class designator sh

8、all be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device perf

9、ormance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard

10、military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devic

11、es which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adver

12、sely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outline. The case outline are as designated in MIL-STD-1835 and as follows: Outline letter

13、 Descriptive designator Terminals Package style X See figure 1 8 Straight leads with side mounting tabs (leads are ceramic sealed) Y See figure 1 8 Straight leads with side mounting through holes 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. Provided by IHSNot for Resale

14、No reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-05241 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Input voltage range -0.5 V dc to +60 V dc (continuous)

15、Lead temperature (soldering, 10 seconds) +300C Storage temperature -55C to +135C 1.4 Recommended operating conditions. Input voltage range +18 V dc to +40 V dc Output power . 30 W Case operating temperature range (TC) . -55C to +85C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, an

16、d handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microci

17、rcuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standar

18、d Microcircuit Drawings. (Copies of these documents are available online at http:/quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing a

19、nd the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device class

20、es D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, mo

21、dify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.

22、2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall

23、 be as specified on figure 2. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

24、S-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-05241 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I a

25、nd shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of devices. Marking of devices shall be in a

26、ccordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall main

27、tain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintain

28、ed under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate o

29、f compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of

30、microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit,

31、or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document r

32、evision level control and shall be made available to either DLA Land and Maritime-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883.

33、(2) TAas specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for

34、 ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-05241 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC +

35、85C VIN= 28 V dc 5%, CL= 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output voltage VOUTVIN= 28 V dc, 100% load on both outputs 1 01 11.88 12.12 V 2,3 11.76 12.24 Output current 1/ 2/ IOUTVIN = 18, 28, and 40 V dc Either output 1,2,3 01 2.3 A Output ripple voltage

36、1/ 3/ VRIPVIN = 18, 28, and 40 V dc, IOUT = 2.3 A, B W = 20 Hz to 2 MHz 1,2,3 01 80 mV p-p Line regulation 3/ VRLINEVIN = 18, 28, and 40 V dc, IOUT= 0, 1.15, and 2.3 A 1,2,3 01 -0.5 +0.5 % Load regulation 3/ VRLOADVIN = 18, 28, and 40 V dc, IOUT= 0, 1.15, and 2.3 A 1,2,3 01 -1.0 +1.0 % Cross regulat

37、ion 4/ VRCROSSVIN = 18, 28, and 40 V dc 1,2,3 01 -3.0 +3.0 % Input current IINIOUT = 0, pin 4 open 1,2,3 01 100 mA Pin 4 shorted to pin 2 1,2,3 8 Efficiency 3/ EFFIOUT = 2.3 A 1,2,3 01 79 % Isolation ISO Input to output or any pin to case (except pin 3) at 500 V dc, TC = +25C 1 01 100 M Maximum capa

38、citive load 5/ 6/ CLIOUT= 2.3 A, each output, TC= +25C 1 01 80 F Power dissipation load fault PDShort circuit, overload 1,2,3 01 14 W Current limit point ILIMVOUT= 90% of nominal4,5,6 01 105 145 % Switching frequency FS100% load 4,5,6 01 425 575 kHz Line rejection 1/ REJ 100% load, DC to 50 kHz, TC=

39、 +25C 1 01 35 dB See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-05241 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. El

40、ectrical performance characteristics - Continued. Test Symbol Conditions -55C TC +85C VIN= 28 V dc 5%, CL= 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output response to step load changes 3/ 7/ VTLD50% to/from 100% load 4,5,6 01 -300 +300 mV pk Recovery time, step

41、load changes 3/ 7/ 8/ TTLD50% to/from 100% load 4,5,6 01 200 s Output response to step line changes 3/ 6/ 9/ VTLNInput step, 18 V to/from 40 V dc, IOUT = 2.3 A 4,5,6 01 -300 +300 mV pk Recovery time, step line changes 3/ 6/ 9/ TTLNInput step, 18 V to/from 40 V dc, IOUT= 2.3 A 4,5,6 01 200 s Turn on

42、overshoot 3/ 10/ VOS10% load, 100% load 4,5,6 01 1000 mV Turn on delay 3/ 10/ TDLY10% load, 100% load 4,5,6 01 10 ms 1/ Applicable to positive and negative outputs. 2/ Output load current must be distributed such that at least 20% of the total current is being provided by one of the outputs. 3/ Load

43、 current split equally between +VOUTand -VOUT. 4/ Cross regulation is measured with 20% rated load on output under test while changing the load on the other output from 20% to 80% of rated. 5/ Capacitive load may be any value from 0 to the maximum limit without compromising dc performance. 6/ Parame

44、ter is tested as part of design characterization or after design changes. Thereafter, parameter shall be guaranteed to the limits specified. 7/ Load step transition time 10 s. 8/ Recovery time is measured from the initiation of the transient to where VOUThas returned to within 1% of its steady state

45、 value at 50% load. 9/ Line step transition time 100 s. 10/ Turn-on delay time is measured from either a step application of input power or a logic low to logic high transition on the inhibit pin (pin 4). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

46、-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-05241 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Symbol Millimeters Inches Min Max Min Max A 10.80 .425 D 70.87 71.37 2.79 2.81 D1 58.29 58.55 2.295 2.305 E 50.67 50.93 1.995 2.005 e1 44.

47、32 44.58 1.745 1.755 e2 37.97 38.23 1.495 1.505 e3 25.27 25.53 .995 1.005 e4/e5/S2 10.03 10.29 .395 .405 F 1.14 1.40 .045 .055 L 6.22 6.48 .245 .255 L1 5.46 5.72 .215 .225 q1 39.24 39.50 1.545 1.555 q2 8.76 9.02 .345 .355 q3 21.46 21.72 .845 .855 S 6.73 6.99 .265 .275 S1 11.81 12.07 .465 .475 S3 4.9

48、5 5.21 .195 .205 b 0.89 1.14 .035 .045 p 3.38 3.63 .133 .143 NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Lead identification for reference only. 3. Case outline weight: 85 grams maximum. FIGURE 1. Case outline. Provided by I