1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device types 05, 06, 07, and 08. Make changes to 1.2.2, 1.3, 1.4, 1.5, Table I, Figure 1 and Figure 2. - ro 06-06-12 R. MONNIN REV SHET REV A A A A A SHEET 15 16 17 18 19 REV STATUS REV A A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6
2、7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY RAJESH PITHADIA COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY RAYMOND MONNIN AND AGENCIES OF THE DEPARTME
3、NT OF DEFENSE DRAWING APPROVAL DATE 06-05-08 MICROCIRCUIT, DIGITAL-LINEAR, 3 V, RS-232, RECEIVER / TRANSMITTER TRANCEIVER, MONOLITHIC SILICON AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-06207 SHEET 1 OF 19 DSCC FORM 2233 APR 97 5962-E477-06 Provided by IHSNot for ResaleNo reproduction or n
4、etworking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06207 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high re
5、liability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The
6、PIN is as shown in the following example: 5962 - 06207 01 Q 3 X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA mar
7、ked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Devic
8、e type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 ICL3243E 3 V VCCRS-232, 5 receivers / 3 transmitters transceiver with shutdown 02 ICL3238E 3 V VCCRS-232, 3 receivers / 5 transmitters transceiver with shutdown 03 ICL3232E 3 V VCCR
9、S-232, 2 receivers / 2 transmitters transceiver 04 ICL3221E 3 V VCCRS-232, 1 receiver / 1 transmitter transceiver with shutdown 05 ICL3243E 5 V VCCRS-232, 5 receivers / 3 transmitters transceiver with shutdown 06 ICL3238E 5 V VCCRS-232, 3 receivers / 5 transmitters transceiver with shutdown 07 ICL32
10、32E 5 V VCCRS-232, 2 receivers / 2 transmitters transceiver 08 ICL3221E 5 V VCCRS-232, 1 receiver / 1 transmitter transceiver with shutdown 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requiremen
11、ts documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 Provided by IHSNot for ResaleNo reproduction or networking permitted wi
12、thout license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06207 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive d
13、esignator Terminals Package style 2 CQCC1-N20 20 Square leadless chip carrier 3 CQCC1-N28 28 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 1.3 Absolute maximum ratings. 1/ V
14、CCto ground . -0.3 V to 6 V V+ to ground . -0.3 V to 7 V V- to ground +0.3 V to -7 V V+ to V- . 14 V Input voltages: TIN, FORCEOFF , FORCEON, EN . -0.3 V to 6 V 2/ RIN25 V Output voltages: TOUT13.2 V ROUT, INVALID -0.3 V to VCC+0.3 V Short circuit duration: TOUTContinuous Storage temperature range .
15、 -65C to +150C Lead temperature (soldering, 10 seconds) . +300C Junction temperature (TJ) : Device types 01, 02, 03, 04, 05, 06, 07, 08 . +175C Thermal resistance, junction-to-case (JC): Cases 2 and 3 . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case 2 . 90C/W Case 3 . 70C/W 1.4
16、Recommended operating conditions. Operating voltage range: Device types 01, 02, 03, and 04 +3.0 V dc to +3.6 V dc Device types 05, 06, 07, and 08 +4.5 V dc to +5.5 V dc Ambient operating temperature range (TA) . -55C to +125C _ 1/ Stresses above the absolute maximum rating may cause permanent damage
17、 to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ EN only applies to device types 04 and 08. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06207 DEF
18、ENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 1.5 ESD performance. TA= 25C RS232 pins ( TOUT, RIN): Human body model : Device types 01, 02, 03, 04, 05, 06, 07, 08 . 15 kV IEC61000-4-2 contact discharge : Device types 01, 02, 03, 04, 05, 06, 07,
19、08 . 8 kV IEC61000-4-2 air gap discharge : Device types 01, 02, 03, 04, 05, 06, 07, 08 . 15 kV All other pins: Human body model : Device types 01, 03, 04, 05, 07, 08 . 2 kV Device types 02, 06 . 2.5 kV 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following spec
20、ification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General S
21、pecification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawin
22、gs. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the t
23、ext of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for dev
24、ice classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device
25、class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V o
26、r MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth tables. The truth tables shall be as specified on figure 2.
27、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06207 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics and pos
28、tirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requi
29、rements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number
30、 is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M s
31、hall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certi
32、ficate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in ord
33、er to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of
34、MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with eac
35、h lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and rev
36、iew for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assign
37、ment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 77 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06207 DEFENSE
38、SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max DC characteristics Supply current, aut
39、omatic powerdown ICCAPDAll RINopen, FORCEON = GND, 1,2,3 03, 07 10 A All RINopen, FORCEON = GND, 01, 02, 04, 05, 10 FORCEOFF = VCC06, 08 Supply current, ICCPD1,2,3 03, 07 10 A powerdown FORCEOFF = GND 01, 02, 04, 05, 10 06, 08 Supply current, powered up ICCPUVCC= 3.0 V, all outputs unloaded, FORCE O
40、N = FORCEOFF = VCC1,2,3 01 1.8 mA VCC= 3.15 V, all outputs unloaded, FORCE ON = FORCEOFF = VCC03,04 1.8 All outputs unloaded, FORCE ON = FORCEOFF = VCC02, 05, 06, 07, 08 1.8 Logic and transmitter inputs and receiver outputs Input logic threshold low VINLTIN, FORCEON, EN , 2/ FORCEOFF 1,2,3 01, 03, 0
41、4, 05, 07, 08 0.8 V TIN, FORCEON, FORCEOFF wake up threshold 02, 06 0.8 01, 03, 04 2.0 Input logic threshold high VINHTIN, FORCEON, EN , 2/ FORCEOFF 1,2,3 05, 07, 08 2.2 V 02 2.0 TIN, FORCEON, FORCEOFF wake up threshold 06 2.4 See footnotes at end of table. Provided by IHSNot for ResaleNo reproducti
42、on or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06207 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA
43、 +125C unless otherwise specified Group A subgroups Device type Limits Unit Min MaxLogic and transmitter inputs and receiver outputs - continued Input leakage current IILTIN, FORCEON, EN , 2/ FORCEOFF 1,2,3 01, 03, 04, 05, 07, 08 10 A TIN, FORCEON, 3/ FORCEOFF , VIN= 0 V or VCC02, 06 10 Output leaka
44、ge current IOLFORCEOFF = GND or EN = VCC2/ 1,2,3 01, 04, 05, 08 10 A FORCEOFF = GND 02, 06 10 Output voltage low VOLIOUT= 1.6 mA 1,2,3 01, 03, 04, 05, 07, 08 0.4 V IOUT= 1.0 mA 02, 06 0.4 Output voltage high VOHIOUT= -1.0 mA 1,2,3 01, 02, 03,04 VCC 0.6 V 05, 06, 07, 08 VCC 0.9 Automatic powerdown Re
45、ceiver input thresholds to enable transmitters VINREPowers up, FORCEON = GND, FORCEOFF = VCC1,2,3 01, 04, 05, 08 -2.7 2.7 V Powers up 03, 07 -2.7 2.7 Receiver input thresholds to disable transmitters VINRDPowers down, FORCEON = GND, FORCEOFF = VCC1,2,3 01, 04, 05, 08 -0.3 0.3 V Powers down 03, 07 -0
46、.3 0.3 INVALID output voltage low VOLAPDIOUT= 1.6 mA, FORCEON = GND, FORCEOFF = VCC1,2,3 01, 04, 05, 08 0.4 V IOUT= 1.6 mA 03, 07 0.4 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A
47、5962-06207 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min MaxAutomatic
48、powerdown - continued. INVALID output voltage high VOHAPD1,2,3 01,04 VCC 0.6 V IOUT= -1.0 mA, FORCEON = GND, FORCEOFF = VCC05, 08 VCC 0.9 IOUT= -1.0 mA 03 VCC 0.6 07 VCC 0.9 Enhanced automatic power down ( FORCEON = GND, FORCEOFF = VCC) Receiver input threshold to INVALID high VINRHINV Powered up 1,2,3 02, 06 -2.7 2.7 V Receiver input threshold to INVALID low VINRLINV Powered down 1,2,3 02, 06 -0.3 0.3 V INVALID output voltage low VOLINV IOUT= 1.0 mA 1,2,3 02, 06 0.4 V 02 VCC 0.6 INVALID output voltage hig
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1