DLA SMD-5962-06242 REV B-2013 MICROCIRCUIT HYBRID LINEAR 15 VOLT SINGLE CHANNEL DC DC CONVERTER.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Table II, add note to Group C end-point test parameters. Update boilerplate paragraphs. -gz 11-03-03 Charles F. Saffle B Add case outline Y. -gc 13-07-02 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV B B B B B B B B B B B OF SHEETS SHEET 1

2、 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Raymond Monnin MICROCIRCUIT, HYBRID, LINEAR, 15 VOLT, SING

3、LE CHANNEL, DC/DC CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 06-06-20 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-06242 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E474-13Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

4、HS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06242 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines a

5、nd lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 06242 01 K X X Federal RHA Device Device Case

6、Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked wit

7、h the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type. The device type identify the circuit function as follows: Device type Generic number Circuit function 01 LS2815S DC/DC converter, 30 W, 15 V output 1.2.3 Device class designator. This device class designator

8、shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device pe

9、rformance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standar

10、d military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates dev

11、ices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adv

12、ersely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outline. The case outline is as designated in MIL-STD-1835 and as follows: Outline lette

13、r Descriptive designator Terminals Package style X See figure 1 8 Straight leads with side mounting tabs (leads are ceramic sealed) Y See figure 1 8 Straight leads with side mounting through holes 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. Provided by IHSNot for Resal

14、eNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06242 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Input voltage range -0.5 V dc to +60 V dc (continuous)

15、 Lead temperature (soldering, 10 seconds) +300C Storage temperature -55C to +135C 1.4 Recommended operating conditions. Input voltage range +18 V dc to +40 V dc Output power . 30 W Case operating temperature range (TC) . -55C to +85C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, a

16、nd handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microc

17、ircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standa

18、rd Microcircuit Drawings. (Copies of these documents are available online at http:/quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing

19、and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device clas

20、ses D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, m

21、odify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3

22、.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shal

23、l be as specified on figure 2. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

24、HS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06242 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I

25、and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of devices. Marking of devices shall be in

26、accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall mai

27、ntain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintai

28、ned under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate

29、of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of

30、 microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit,

31、 or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document

32、revision level control and shall be made available to either DLA Land and Maritime-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883.

33、 (2) TAas specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot fo

34、r ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06242 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC

35、+85C VIN= 28 V dc 5%, CL= 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output voltage VOUTIOUT= 2 A 1 01 14.85 15.15 V 2,3 14.70 15.30 Output current 1/ IOUTVIN = 18, 28, and 40 V dc 1,2,3 01 2 A Output ripple voltage 2/ VRIPVIN = 18, 28, and 40 V dc, IOUT = 2 A, B

36、W = 20 Hz to 2 MHz 1,2,3 01 80 mV p-p Line regulation VRLINEVIN = 18, 28, and 40 V dc, IOUT= 0, 1, and 2 A 1,2,3 01 -0.5 +0.5 % Load regulation VRLOADVIN = 18, 28, and 40 V dc, IOUT= 0, 1, and 2 A 1,2,3 01 -1.0 +1.0 % Input current IINIOUT = 0, pin 4 open 1,2,3 01 70 mA Pin 4 shorted to pin 2 1,2,3

37、8 Efficiency EFFIOUT = 2 A 1,2,3 01 78 % Isolation ISO Input to output or any pin to case (except pin 3) at 500 V dc, TC = +25C 1 01 100 M Maximum capacitive load 3/ 4/ CLIOUT= 2 A, each output, TC= +25C 4 01 120 F Power dissipation load fault PDShort circuit, overload 1,2,3 01 14 W Current limit po

38、int ILIMVOUT= 90% of nominal4,5,6 01 105 145 % Switching frequency FS100% load 4,5,6 01 425 575 kHz Line rejection 3/ REJ 100% load, DC to 50 kHz, TC= +25C 1 01 35 dB See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAN

39、DARD MICROCIRCUIT DRAWING SIZE A 5962-06242 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC +85C VIN= 28 V dc 5%, CL= 0 unless otherwise specified Group A subgro

40、ups Device type Limits Unit Min Max Output response to step load changes 5/ VTLD50% to/from 100% load 4,5,6 01 -300 +300 mV pk Recovery time, step load changes 5/ 6/ TTLD50% to/from 100% load 4,5,6 01 200 s Output response to step line changes 3/ 7/ VTLNInput step, 18 V to/from 40 V dc, IOUT = 2 A 4

41、,5,6 01 -300 +300 mV pk Recovery time, step line changes 3/ 6/ 7/ TTLNInput step, 18 V to/from 40 V dc, IOUT= 2 A 4,5,6 01 200 s Turn on overshoot VOS10% load, 100% load 4,5,6 01 1000 mV Turn on delay 8/ TDLY10% load, 100% load 4,5,6 01 10 ms 1/ Parameter verified during line and load tests 2/ Guara

42、nteed for a DC to 2 MHz bandwidth. Tested using a 20 kHz to 2 MHz bandwidth. 3/ Parameter is tested as part of design characterization or after design changes. Thereafter, parameter shall be guaranteed to the limits specified. 4/ Capacitive load may be any value from 0 to the maximum limit without c

43、ompromising dc performance. 5/ Load step transition time 10 s. 6/ Recovery time is measured from the initiation of the transient to where VOUThas returned to within 1% of its steady state value at 50% load. 7/ Line step transition time 100 s. 8/ Turn-on delay time from either a step application of i

44、nput power or a logic low to logic high transition on the enable pin (pin 4) while power is applied to the input. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06242 DLA LAND AND MARITIME COLUMBUS, OHIO 432

45、18-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Symbol Millimeters Inches Min Max Min Max A 10.80 .425 D 70.87 71.37 2.79 2.81 D1 58.29 58.55 2.295 2.305 E 50.67 50.93 1.995 2.005 e1 44.32 44.58 1.745 1.755 e2 37.97 38.23 1.495 1.505 e3 25.27 25.53 .995 1.005 e4/e5/S2 10.03 10

46、.29 .395 .405 F 1.14 1.40 .045 .055 L 6.22 6.48 .245 .255 L1 5.46 5.72 .215 .225 q1 39.24 39.50 1.545 1.555 q2 8.76 9.02 .345 .355 q3 21.46 21.72 .845 .855 S 6.73 6.99 .265 .275 S1 11.81 12.07 .465 .475 S3 4.95 5.21 .195 .205 b 0.89 1.14 .035 .045 p 3.38 3.63 .133 .143 NOTES: 1. The U.S. government

47、preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Lead identification for reference only. 3. Case outline weight: 80 gram

48、s maximum. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06242 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 Case outline Y. Symbol Millimeters Inches Min Max Min Max A 10.80 0.425 D 70.87 71.37 2.79 2.81 D1 58.29 58.55 2.295 2.305 E 37.97 38.23 1.4