DLA SMD-5962-08212 REV B-2012 MICROCIRCUIT HYBRID LINEAR +3 3 VOLT AND 5 V TRIPLE CHANNEL DC-DC CONVERTER.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changed the output power from 25 W to 30 W under paragraph 1.2.2 and paragraph 1.3. Changed the test condition IOUT= 3.0 A to IOUT= 4.5 A throughout the table I. Table I; Changed the output current maximum limit from 3.0 A to 4.5 A. -sld 09-03-03

2、 Robert M. Heber B Table I: For power dissipation test, change max limit of non-RHA subgroup 1 from “26” W to “28” W (2 pls). Table II, add note to Group C end-point test parameters to include subgroups 2 and 3. In paragraph 4.3.5, correct units in table for Single event upset survival level (LET) f

3、rom “MeV” to “MeV-cm2/mg”. Update drawing paragraphs. gc 12-03-01 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Steve Duncan DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Ce

4、cil COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE APPROVED BY Robert M. Heber MICROCIRCUIT, HYBRID, LINEAR, +3.3 VOLT AND 15 V, TRIPLE CHANNEL, DC-DC CONVERTER DRAWING APPROVAL DATE 08-04-24

5、AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-08212 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E233-12Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-08212 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-399

6、0 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When

7、available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 08212 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (

8、see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The de

9、vice type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 SMRT283R315T DC-DC converter, 30 W, +3.3 V and 15 V outputs 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels a

10、re defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is i

11、ntended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process

12、 Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(

13、s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quali

14、ty level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-08212 DLA LAND AND MARITIME COLUMBUS,

15、OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 12 Flange mount 1.2.5 Lead finish. The lead finish shall be as spec

16、ified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input voltage range (VIN) -0.5 V dc to +80 V dc Power dissipation (PD): Device type 01 (non-RHA) . 28 W Device type 01 (RHA levels P, R, and F) . 30 W Output power . 30 W Lead soldering temperature (10 seconds) . +300C Storage temperature rang

17、e -65C to +150C 1.4 Recommended operating conditions. Input voltage range (VIN) +19 V dc to +50 V dc Case operating temperature range (TC) -55C to +125C 1.5 Radiation features. Maximum total dose available (dose rate = 9 rads(Si)/s): Device type 01 (RHA levels P, R, and F) . 300 krads (Si) 2/ 2. APP

18、LICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPAR

19、TMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - L

20、ist of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 1/ Stresses

21、above the absolute maximum ratings may cause permanent damage to the device. Input voltage transients between 56 V to 80 V are allowed for no more than 120 milliseconds. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ These parts may be dose rate sensitive

22、 in a space environment and may demonstrate enhanced low dose rate effects. Radiation end-point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, method 1019, condition C, tested at 9 rads(Si)/s. Provided by IHSNot for ResaleNo reproduction or networ

23、king permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-08212 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited her

24、ein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall

25、be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests

26、and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and

27、 physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure

28、2. 3.2.3 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing and acquiring activity upon request. 3.3 Electrical performance characteristics. Unless otherwise specified h

29、erein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup a

30、re defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requir

31、ements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manual

32、ly tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be

33、 required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certific

34、ate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Man

35、agement (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-08212 DLA LAND AND MARITIME COLUMBUS, OHIO 4

36、3218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ -55C TC +125C VIN= 28 V dc 0.5 V dc no external sync, CL= 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output voltage VOUTIOUT= 4.5

37、 A (main) 1 01 3.267 3.333 V 2,3 3.234 3.366 P,R,F 1,2,3 3.185 3.416 IOUT= 500 mA (+aux) 1 14.85 15.15 2,3 14.70 15.30 P,R,F 1,2,3 14.48 15.53 IOUT= 500mA (-aux) 1 14.63 15.36 2,3 14.48 15.53 P,R,F 1,2,3 14.25 15.75 Output current 3/ IOUTVIN= 19 V dc, 28 V dc, and 50 V dc (main) 1,2,3 01 4.5 A P,R,F

38、 1,2,3 4.5 VIN= 19 V dc, 28 V dc, and 50 V dc (aux) 1,2,3 800 mA P,R,F 1,2,3 800 Output ripple voltage VRIPB.W. 20 MHz, IOUT= 4.5 A (main) 1,2 01 180 mVp-p 3 200 P,R,F 1,2,3 250 B.W. 20 MHz, IOUT= 500 mA (aux) 1,2 140 3 150 P,R,F 1,2,3 200 See footnotes at end of table. Provided by IHSNot for Resale

39、No reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-08212 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2

40、/ -55C TC +125C VIN= 28 V dc 0.5 V dc no external sync, CL= 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Line regulation VRLINEVIN= 19 V dc to/from 50 V dc, IOUT= 4.5 A (main) 1,2,3 01 30 mV P,R,F 1,2,3 60 VIN= 19 V dc to/from (+aux) 50 V dc, IOUT= 500 mA (-aux) 1,2

41、,3 30 1,2,3 70 P,R,F 1,2,3 100 Load regulation VRLOADIOUT= 0 to 4.5 A (main) 1,2,3 01 40 mV P,R,F 1,2,3 60 IOUT= 0 to 500 mA, (+aux) both outputs changed simultaneously (-aux) 1,2,3 40 1,2,3 300 P,R,F 1,2,3 400 Input current IINAll IOUT= 0, Inhibit (pin) 3 = 0 V dc (tied to pin 2) 1,2,3 01 50 mA P,R

42、,F 1,2,3 60 All IOUT= 0, Inhibit (pin) 3 = open 1,2,3 110 P,R,F 1,2,3 120 Input ripple current 4/ IRIPIOUT= 4.5 A (main), IOUT= 500 mA (aux), B. W. 20 MHz 1,2,3 01 50 mAp-p P,R,F 1,2,3 60 Efficiency Eff IOUT= 4.5 A, (main) IOUT= 500 mA (aux) 1 01 69 % 2,3 68 P,R,F 1,2,3 65 See footnotes at end of ta

43、ble. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-08212 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Cont

44、inued. Test Symbol Conditions 1/ 2/ -55C TC +125C VIN= 28 V dc 0.5 V dc no external sync, CL= 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Isolation ISO Input to either output or to sync return, or any pin to case at 500 V dc 1 01 100 M TC= +25C P,R,F 1 100 Capaciti

45、ve load 5/ 6/ CLNo affect on dc (main) 4 01 5000 F performance TC= +25C P,R,F 4 5000 No affect on dc (aux) 4 1000 performance TC= +25C P,R,F 4 1000 Power dissipation PDShort circuit on main, PD= PIN- total POUT 1,2,3 01 28 W P,R,F 1,2,3 30 Short circuit on both aux outputs simultaneously, PD= PIN- t

46、otal POUT1,2,3 28 P,R,F 1,2,3 30 Switching frequency FSIOUT= 4.5 A (main), IOUT= 500 mA (aux) 4 01 270 330 kHz 5,6 270 330 P,R,F 4,5,6 270 330 External sync range 7/ FSYNCIOUT= 4.5 A (main), IOUT= 500 mA (aux), 4,5,6 01 270 330 kHz TTL level to pin 4 P,R,F 4,5,6 270 330 See footnotes at end of table

47、. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-08212 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continu

48、ed. Test Symbol Conditions 1/ 2/ -55C TC +125C VIN= 28 V dc 0.5 V dc no external sync, CL= 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output response to step load transient 8/ VTLOAD50% load to/from (main) 100% load4,5,6 01 -450 +450 mV pk P,R,F 4,5,6 -700 +700 50% load to/from (aux) 100% load, balanced loads on each output 4,5,6 -450 +450 P,R,F 4,5,6 -700 +700 Recovery time f