DLA SMD-5962-08226-2008 MICROCIRCUIT HYBRID LINEAR 32 CHANNEL ANALOG MULTIPLEXER《模拟多路复用32通道线性混合微电路》.pdf

1、 4REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV SHEET REV SHEET 15 16 17 REV STATUS REV OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Steve Duncan DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil COLUMBUS, OHIO 43218-3990 http:/www.d

2、scc.dla.mil/ THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Robert M. Heber MICROCIRCUIT, HYBRID, LINEAR, 32 CHANNEL, ANALOG MULTIPLEXER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 08-04-07 AMSC N/A REVISION LEVEL SIZE A CAGE CODE 67268 5962-08226 SHEET 1 OF 17

3、DSCC FORM 2233 APR 97 5962-E280-08Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-08226 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope

4、. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are refl

5、ected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 08226 01 K X C Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiati

6、on hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type

7、Generic number Circuit function 01 ACT8508 32 channel analog multiplexer, high impedance analog input with ESD protection 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PR

8、F-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H

9、 Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited tem

10、perature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that cl

11、ass. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturer

12、s internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-08226 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL

13、 SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 96 Ceramic quad flat pack 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534

14、. 1.3 Absolute maximum ratings. 1/ Positive supply voltage between +VCCand GND . +20 V dc Negative supply voltage between -VEEand GND. -20 V dc VREFto GND. +20 V dc Digital input overvoltage range: VEN(pins 5 and 92). ( GND - 4)V VA(pins 1, 3, 93, and 95) ( GND - 4)V VB(pins 2, 4, 94, and 96) ( GND

15、- 4)V Analog input overvoltage range . -18 V dc VS +18 V dc Power dissipation (PD) . 40 mW Thermal resistance junction-to-case (JC) 10C/W 2/ Storage temperature -55C to +150C Lead temperature (soldering, 10 seconds). +300C 1.4 Recommended operating conditions. Positive supply voltage (+VCC) 3/ . +15

16、 V dc Negative supply voltage (-VEE) 3/. -15 V dc VREF3/ +5 V dc Logic low level voltage (VAL) +0.8 V dc Logic high level voltage (VAH) +4.0 V dc Case operating temperature range (TC). -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specifi

17、cation, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for

18、. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade perf

19、ormance and affect reliability. 2/ Based on the maximum power dissipation spread over the multiplexer die. 3/ Supply voltages must be applied simultaneously or with the +5 V reference supply first and then the +15 V and -15 V supplies. Provided by IHSNot for ResaleNo reproduction or networking permi

20、tted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-08226 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Micro

21、circuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict

22、 between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item perfor

23、mance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device clas

24、s. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the devic

25、e for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal

26、connections. The terminal connections shall be as specified on figure 2. 3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3. 3.2.4 Switching waveform(s). The switching waveform(s) shall be as specified on figure 4. 3.2.5 Block diagram. The block diagram shall be as specified

27、on figure 5. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements s

28、hall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor si

29、milar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device

30、 type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request.

31、 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and

32、 herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWI

33、NG SIZE A 5962-08226 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Test Symbol Conditions 1/ 2/ -55C TC +125C unless otherwise specified Group A subgroups Device type Min Max Unit +ICCVEN(

34、0-31)= VA(0-3)A= VA(0-3)B= 0 1,2,3 01 0.1 1 mA -ICC VEN(0-31)= VA(0-3)A= VA(0-3)B= 0 1,2,3 01 -1 -0.1 mA +ISBY VEN(0-31)= 4 V, VA(0-3)A= VA(0-3)B= 0 3/ 1,2,3 01 0.1 1 mA Supply currents -ISBY VEN(0-31)= 4 V, VA(0-3)A= VA(0-3)B= 0 3/ 1,2,3 01 -1.0 -0.1 mA IAL(0-3)VA= 0 V 2/ 1,2,3 01 -1 1 A Address in

35、put currents IAH(0-3) VA= 5 V 2/ 1,2,3 01 -1 1 A IENL(0-15) VEN(0-15)= 0 V 1,2,3 01 -1 1 A IENH(0-15)VEN(0-15)= 5 V 1,2,3 01 -1 1 A IENL(16-31)VEN16-31)= 0 V 1,2,3 01 -1 1 A Enable input current IENH(16-31)VEN(16-31)= 5 V 1,2,3 01 -1 1 A See footnotes at end of table. Provided by IHSNot for ResaleNo

36、 reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-08226 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Con

37、ditions 1/ 2/ -55C TC +125C unless otherwise specified Group A subgroups Device type Min Max Unit +ISOFFOUTPUT(ALL) VIN= +10 V, VEN= 4 V, output and all unused inputs = -10 V 4/ 5/ 1,2,3 01 -100 +700 nA Positive input leakage current (CH0-CH31) +ISOFFCURRENT(ALL) VIN= +10 V, VEN= 4 V, output and all

38、 unused inputs = -10 V 4/ 5/ 1,2,3 01 -100 +700 nA -ISOFFOUTPUT(ALL) VIN= -10 V, VEN= 4 V, output and all unused inputs = +10 V 4/ 5/ 1,2,3 01 -100 +700 nA Negative input leakage current (CH0-CH31) -ISOFFCURRENT(ALL) VIN= -10 V, VEN= 4 V, output and all unused inputs = +10 V 4/ 5/ 1,2,3 01 -100 +700

39、 nA +IDOFFOUTPUT(ALL) VIN= +10 V, VEN= 4 V, output and all unused inputs = -10 V 5/ 6/ 1,2,3 01 -100 +100 nA +IDOFFCURRENT(ALL) VIN= +10 V, VEN= 4 V, output and all unused inputs = -10 V 5/ 6/ 1,2,3 01 -100 +100 nA -IDOFFOUTPUT(ALL) VIN= -10 V, VEN= 4 V, output and all unused inputs = +10 V 5/ 6/ 1,

40、2,3 01 -100 +100 nA Output leakage current outputs (pins 25 and 70) -IDOFFCURRENT(ALL) VIN= -10 V, VEN= 4 V, output and all unused inputs = +10 V 5/ 6/ 1,2,3 01 -100 +100 nA See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

41、-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-08226 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions 1/ 2/ -55C TC +125C unless otherwise specified Group A s

42、ubgroups Device type Min Max Unit 1 18.0 23.0 2 18.0 23.5 +VCLMP(0-31) VEN= 4 V, all unused inputs are open 5/ 3 01 17.5 22.5 V 1 -23.0 -18.0 2 -23.5 -18.0 Input clamped voltage (CH0-CH31) -VCLMP(0-31) VEN= 4 V, all unused inputs are open 5/ 3 01 -22.5 -17.5 V RDS(ON)(0-31)AVIN= +15 V, VEN= 0.8 V, I

43、OUT= -1 mA 4/ 5/ 7/ 1,2,3 01 500 3000 RDS(ON)(0-31)BVIN= +5 V, VEN= 0.8 V, IOUT= -1 mA 4/ 5/ 7/ 1,2,3 01 500 3000 Switch ON resistance outputs (pins 25 and 70) RDS(ON)(0-31)CVIN= -5 V, VEN= 0.8 V, IOUT= +1 mA 4/ 5/ 7/ 1,2,3 01 500 3000 tONA RL= 10 k, CL= 50 pF, See figure 4 9,10,11 01 10 1500 ns 9,1

44、0 10 2000 tOFFA RL= 10 k, CL= 50 pF, See figure 4 11 01 10 5000 ns tONEN RL= 1 k, CL= 50 pF, See figure 4 9,10,11 01 10 1500 ns Switching tests tOFFEN RL= 1 k, CL= 50 pF, See figure 4 9,10,11 01 10 1000 ns See footnotes at top of next page. Provided by IHSNot for ResaleNo reproduction or networking

45、permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-08226 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. 1/ +VCC= +15 V dc, -VEE= -15 V dc, and VREF= +5 V

46、dc, unless otherwise specified. 2/ Measure inputs sequentially. Ground all unused inputs. 3/ If not tested, shall be guaranteed to the limits specified in table I. 4/ VINis the applied input voltage to the input channels (CH0-CH31). 5/ VENis the applied input voltage to the enable lines EN(0-15) and

47、 EN(16-31). 6/ VOUTis the applied input voltage to the output lines (OUTPUT(0-15) and OUTPUT(16-31). 7/ Negative current is the current flowing out of each of the pins. Positive current is the current flowing into each of the pins. Provided by IHSNot for ResaleNo reproduction or networking permitted

48、 without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-08226 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 9 DSCC FORM 2234 APR 97 Case outline X. FIGURE 1. Case outline(s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-08226 D