DLA SMD-5962-09212 REV D-2010 MICROCIRCUIT HYBRID LINEAR POSITIVE LOW DROPOUT ADJUSTABLE VOLTAGE REGULATOR.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV SHET REV SHET REV STATUS REV OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Steve Duncan COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING

2、IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Charles F. Saffle MICROCIRCUIT, HYBRID, LINEAR, POSITIVE, LOW DROPOUT, ADJUSTABLE VOLTAGE REGULATOR AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 10-12-15 AMSC N/A REVISION LEVEL SIZE A CAGE CODE 67268 5962-09212 SHEET 1 OF 13 DSC

3、C FORM 2233 APR 97 5962-E209-09Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09212 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawi

4、ng documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the

5、 PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 R 09212 01 K X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness

6、assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type. The device type identify the circuit function as follows: Device type Generic number Cir

7、cuit function 01 MSK 5971RH Radiation hardened, 3.0 A, adjustable voltage regulator 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification

8、as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level

9、. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified

10、 incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specif

11、ied in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This p

12、roduct may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09212 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outli

13、nes. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style U See figure 1 3 Bottom terminal chip carrier, ceramic X See figure 1 3 TO-257AA with tab, straight leads, glass sealed Y See figure 1 3 TO-257AA with tab, leads for

14、med up, glass sealed Z See figure 1 3 TO-257AA with tab, leads formed down, glass sealed 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Supply voltage (VIN- VOUT) . +30 V dc Output current 3.0 A 2/ Junction temperature (TJ) +150C Thermal r

15、esistance, junction-to-case (JC), TC= +125C: Case outline U 2.5C/W Case outlines X, Y, and Z . 3.5C/W Storage temperature -65C to +150C Lead temperature (soldering, 10 seconds). +300C 1.4 Recommended operating conditions. Supply voltage (VIN- VOUT) +1.5 V dc to +24 V dcCase operating temperature ran

16、ge (TC) . -55C to +125C 1.5 Radiation features. Maximum total dose available 100 krads (Si) 3/ 4/ 5/ 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unles

17、s otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 -

18、Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Stan

19、dardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ For compliance with MIL

20、-PRF-38535 appendix A current density specifications, the maximum output current is derated to 2 A. 3/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects. Radiation end-point limits for the noted parameters are guaranteed only for the con

21、ditions as specified in MIL-STD-883, method 1019, condition A. Dose rate shall be in accordance with MIL-STD-883, method 1019, condition A. 4/ Bipolar device types may degrade from displacement damage from radiation which could affect RHA levels. These device types have not been characterized for di

22、splacement damage. 5/ See figure 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09212 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence.

23、In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements.

24、The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for th

25、e applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit,

26、or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figur

27、e 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Radiation exposure circuits. The radiation exposure circuits shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance

28、 characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Markin

29、g of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufact

30、urer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if an

31、y, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in orde

32、r to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL

33、-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification i

34、n the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09212 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 5 DSCC

35、 FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ 3/ -55C TC+125C unless otherwise specified Group A subgroups Device type Limits Unit Min MaxReference voltage VREFVIN= VOUT+ 3 V, IOUT= 10 mA 1 01 1.238 1.262 V 2,3 1.225 1.270 M,D,P,L,R 1/ 1 01 1.225 1.2

36、62 Dropout voltage VDO10 mA IOUT 3.0 A 1,2,3 01 1.5 V Line regulation VRLINE(VOUT+ 3 V) VIN (VOUT+ 15 V), IOUT= 10 mA 1 01 -0.50 0.50 % 2,3 -0.75 0.75 Load regulation VRLOADVIN= VOUT+ 3 V, 10 mA IOUT 3.0 A 1 01 -1.0 1.0 % 2,3 -2.0 2.0 Short circuit current 4/ ISCVIN= VOUT+ 5 V, TC= +25C 1 01 3.0 A R

37、ipple rejection 5/ RR IOUT= 1.5 A, COUT= 25 F, f = 120 Hz 1,2,3 01 60.0 dB 1/ Device type 01 has been characterized through all levels M, D, P, L, R of irradiation and tested to 1.5 times at the R level. Pre and post irradiation values are identical unless otherwise specified in table I. When perfor

38、ming post irradiation electrical measurements for any RHA level, TC= +25C. 2/ Unless otherwise specified, VIN= VOUT+ 5 V, IOUT= 10 mA, COUT= 22 F minimum. 3/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects. Radiation end-point limits f

39、or the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, method 1019, condition A. 4/ For compliance with MIL-PRF-38535 appendix A current density specifications, the maximum output current is derated to 2 A. 5/ Guaranteed by design but not tested. Parameter shall

40、be tested as part of the initial characterization and after design and process changes. Parameter shall be guaranteed to limits specified in table I for all lots not specifically tested. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROC

41、IRCUIT DRAWING SIZE A 5962-09212 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 6 DSCC FORM 2234 APR 97 Case outline U. Symbol Millimeters Inches Min Max Min Max A - 3.30 - .130 A1 0.305 0.457 .012 .018 b 9.27 9.78 .365 .385 b1 10.29 10.80 .405 .425 b2 3.30 3.81 .130 .150 b3 3.

42、86 4.11 .152 .162 D 15.62 16.13 .615 .635 D1 0.76 .030 E 11.18 11.68 .440 .460 e 0.89 .035 S1 0.81 1.07 .032 .042 S2 1.14 1.40 .045 .055 NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems i

43、nvolving conflicts between the metric and inch-pound units, the inch- pound units shall rule. 2. Lead identification for reference only. 3. Case outline U weight: 2.2 grams typical. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

44、-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09212 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Symbol Millimeters InchesMin Max Min Max A - 5.33 - .210 A1 0.89 1.14 .035 .045 A2 2.79 3.30 .110 .130 b 0.71 0.81 .028 .032 D 16.26 16.76

45、 .640 .660 D1/E 10.29 10.80 .405 .425 e 2.54 TYP .100 TYP e1 5.08 REF .200 REF L 10.16 - .400 - L1 13.39 13.64 .527 .537 P 3.56 3.81 .140 .150 S1 2.73 REF .1075 REF NOTES: 1. Pin 1 is indicated by the ESD marking on the package. Pin numbers are for reference only. 2. The U. S. Government preferred s

46、ystem of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall take precedence. 3. Case outline X weight: 3.2 grams typical. FIGURE 1. Case outlines - Con

47、tinued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09212 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 8 DSCC FORM 2234 APR 97 Case outline Y. Symbol Millimeters InchesMin Max Min

48、Max A - 5.33 - .210 A1 0.89 1.14 .035 .045 A2 2.79 3.30 .110 .130 b 0.71 0.81 .028 .032 D 16.26 16.76 .640 .660 D1/E 10.29 10.80 .405 .425 e 2.54 TYP .100 TYP e1 5.08 REF .200 REF L 2.16 2.67 .085 .105 L1 13.39 13.64 .527 .537 L2 5.08 - .200 - P 3.56 3.81 .140 .150 S1 2.73 REF .1075 REF NOTES: 1. Pin 1 is indicated by the ESD marking on the package. Pin numbers are