DLA SMD-5962-09223 REV A-2011 MICROCIRCUIT LINEAR PRECISION LOW NOISE LOW INPUT BIAS CURRENT OPERATIONAL AMPLIFIER MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV SHET REV SHET REV STATUS REV OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR U

2、SE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAJESH PITHADIA APPROVED BY CHARLES F. SAFFLE MICROCIRCUIT, LINEAR, PRECISION LOW NOISE, LOW INPUT BIAS CURRENT OPERATIONAL AMPLIFIER, MONOLITHIC SILICON DRAWING APPROVAL DATE 11-01-11 AMSC N/A REVISION LEVEL SIZE A CAGE CODE

3、 67268 5962-09223 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E300-10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09223 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 2 DSCC FORM 2234 A

4、PR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). Whe

5、n available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 L 09223 01 V H A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Le

6、adfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA level

7、s and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 AD8671 Precision low noise, low input bias current operational amplifier 1.2.

8、3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance wi

9、th MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style H GDFP1-F10 10 Flat pack1.2.5 Lead finish. The lead finish i

10、s as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09223 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-399

11、0 REVISION LEVEL SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (+VSto -VS) . 36 V Input voltage (VIN) . -VSto +VSDifferential input voltage 0.7 V Output short circuit duration . Indefinite Power dissipation (PD) . 2/ Junction temperature (TJ) +150C Lead temperature (s

12、oldering, 10 seconds) . +300C Storage temperature range -65C to +150C Thermal resistance, junction-to-case (JC) 66C/W Thermal resistance, junction-to-ambient (JA) . 370C/W 3/ 1.4 Recommended operating conditions. Supply voltage (VS) : VSdual supply mode 5 V to 15 V 0 V / +VSsingle supply mode . 0 V

13、/ +10 V to 0 V / +30 V Ambient operating temperature range (TA) -55C to +125C 1.4.1 Operating performance characteristics: 4/ Common mode input capacitance (CINCM) 6.25 pF Differential mode input capacitance (CINDM) . 7.5 pF Input resistance (RIN) 3.5 G Differential mode input resistance (RINDM) 15

14、M Settling time (tS): VS= 5 V: To 0.1%, 4 V step, gain (G) = 1 1.4 s To 0.01%, 4 V step, gain (G) = 1 5.1 s VS= 15 V: To 0.1%, 10 V step, gain (G) = 1 2.2 s To 0.01%, 10 V step, gain (G) = 1 6.3 s Current noise density (in) (f = 1 kHz) 0.3 pA / HzOutput current (VS= 5 V) . 10 mA Output current (VS=

15、15 V) . 20 mA Short circuit current (VS= 15 V) . 30 mA _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Absolute maximum power dissipation is limited by ensuring in th

16、e application of the absolute maximum junction temperature (TJ) of 150C is not exceed. Actual application power dissipation (including what is required for output drive current) and case to ambient thermal resistance (CA) will determine the maximum TJas described in section 6.7.1. 3/ Measurement tak

17、en under absolute worst case conditions of still air chamber while mounted above the printed circuit board (PCB) to minimize PCB mounting heat sinking effects. 4/ Unless otherwise specified, VS= 5 V to 15 V, VCM= 0.0 V, TA= +25C. Provided by IHSNot for ResaleNo reproduction or networking permitted w

18、ithout license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09223 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 4 DSCC FORM 2234 APR 97 1.5 Radiation features. Maximum total dose available (dose rate = 50 300 rads(Si)/s) . 50 krads(Si) 5/ 2. APPLICABLE DOCUMENTS 2.1

19、Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECI

20、FICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Stand

21、ard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence

22、. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements

23、. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Th

24、e individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-385

25、35 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Radiation exposure circuit

26、. The radiation exposure circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing and acquiring activity upon request. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified

27、 herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. Th

28、e electrical tests for each subgroup are defined in table I. _ 5/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects. Radiation end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883, met

29、hod 1019, condition A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09223 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance charac

30、teristics. Test Symbol Conditions 1/ 2/ -55C TA+125C Group A subgroups Device type Limits Unit VS= 5 V, VCM= 0 V unless otherwise specified Min Max Input characteristics section Offset voltage VOS1 01 -75 +75 V 2,3 -125 +125M,D,P,L 1 -200 +200 Offset voltage drift VOS/ T 3/ 2,3 01 0.5 V/C Input bias

31、 current IB1 01 -12 +12 nA 2,3 -40 +40 M,D,P,L 1 -200 200Input offset current IOS1 01 -12 +12 nA 2,3 -40 +40 M,D,P,L 1 -40 +40 Input voltage range IVR 1,3 01 -2.5 +2.5 V 2 -2.25 +2.25 M,D,P,L 1 -2.5 +2.5 Common mode rejection ratio CMRR VCM= IVR max to IVR min 1,2,3 01 100 dB M,D,P,L 1 100Large sign

32、al voltage gain AVOVO= -3 V to +3 V, 1,2,3 01 1000 V/mV RL= 2 k M,D,P,L 1 1000 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09223 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3

33、990 REVISION LEVEL SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ 2/ -55C TA+125C Group A subgroups Device type Limits Unit VS= 5 V, VCM= 0 V unless otherwise specified Min Max Output characteristics section Output low voltage VOLRL

34、= 600 1,2,3 01 -3.7 V M,D,P,L 1 -3.7 RL= 2 k 1,2,3 -3.8 M,D,P,L 1 -3.8 Output high voltage VOHRL= 600 1,2,3 01 +3.7 V M,D,P,L 1 +3.7 RL= 2 k 1,2,3 +3.8 M,D,P,L 1 +3.8 Power supply section Power supply rejection ratio PSRR VS= 4 V to 18 V 1,2,3 01 110 dB M,D,P,L 1 110Supply current ISVO= 0 V 1 01 3.5

35、 mA 2,3 4.2M,D,P,L 1 4.2 Dynamic performance section Gain bandwidth product GBP 3/ 4/ 4,5,6 01 10 MHz Slew rate SR 3/ 4/ 4 01 4.0 V/s 5 5.06 3.0Noise performance section Peak to peak noise enp-p0.1 Hz to 10 Hz 3/ 4/ 4 01 100 nVpp Voltage noise density enf = 1 kHz 3/ 4/ 4 01 3.8 nV / Hz See footnotes

36、 at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09223 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteris

37、tics Continued. Test Symbol Conditions 1/ 2/ -55C TA+125C Group A subgroups Device type Limits Unit VS= 15 V, VCM= 0 V unless otherwise specified Min Max Input characteristics section. Offset voltage VOS1 01 -75 +75 V 2,3 -125 +125M,D,P,L 1 -200 +200 Offset voltage drift VOS/ T 3/ 2,3 01 0.5 V/C Inp

38、ut bias current IB1 01 -12 +12 nA 2,3 -40 +40 M,D,P,L 1 -200 +200Input offset current IOS1 01 -12 +12 nA 2,3 -40 +40 M,D,P,L 1 -40 +40 Input voltage range IVR 1,2,3 01 -12 +12 V M,D,P,L 1 -12 +12 Common mode rejection ratio CMRR VCM= IVR max to IVR min 1,2,3 01 100 dB M,D,P,L 1 100Large signal volta

39、ge gain AVOVO= -10 V to +10 V , 1,2,3 01 1000 V/mV RL= 2 k M,D,P,L 1 1000 Output characteristics section Output low voltage VOLRL= 600 1,3 01 -11 V 2 -10.4 M,D,P,L 1 -11RL= 2 k 1,2,3 -13.2 M,D,P,L 1 -13.2See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permit

40、ted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09223 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ 2/ -55C TA+125C Group A subgroups Device

41、type Limits Unit VS= 15 V, VCM= 0 V unless otherwise specified Min Max Output characteristics section - continued. Output high voltage VOHRL= 600 1,3 01 +11 V 2 +10.4 M,D,P,L 1 +11 RL= 2 k 1,2,3 +13.2 M,D,P,L 1 +13.2 Power supply section Power supply rejection ratio PSRR VS= 4 V to 18 V 1,2,3 01 110

42、 dB M,D,P,L 1 110Supply current ISVO= 0 V 1 01 3.5 mA 2,3 4.2M,D,P,L 1 4.2 Dynamic performance section Gain bandwidth product GBP 3/ 4/ 4,5,6 01 10 MHz Slew rate SR 3/ 4/ 4 01 3.5 V/s 5 5.0 6 3.0Noise performance section Peak to peak noise enp-p0.1 Hz to 10 Hz 3/ 4 01 100 nVppVoltage noise density e

43、nf = 1 kHz 3/ 4/ 4 01 3.8 nV / Hz 1/ RHA devices supplied to this drawing have been characterized through all levels M, D, P, and L of irradiation. However, this device is tested only at the “L” level. Pre and Post irradiation values are identical unless otherwise specified in Table I. When performi

44、ng post irradiation electrical measurements for any RHA level, TA= +25C. 2/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects. Radiation end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-ST

45、D-883, method 1019, condition A. 3/ Parameter not tested post irradiation. 4/ Tested initially and after any design or process changes which may affect that parameter, and therefore shall be guaranteed to the limits specified in table I herein. Provided by IHSNot for ResaleNo reproduction or network

46、ing permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09223 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 9 DSCC FORM 2234 APR 97 Device type 01 Case outline H Terminal number Terminal symbol 1 NC2 NC 3 -INPUT 4 +INPUT 5 -VS6 NC7 OUTPUT 8 +VS9 NC

47、10 NC NC = No connection FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09223 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 10 DSCC FORM 2234 APR 97 3.5

48、 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be m