DLA SMD-5962-11218 REV A-2012 MICROCIRCUIT HYBRID LINEAR SINGLE CHANNEL DC-DC CONVERTER.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 05. Paragraph 1.4; Correct Input Voltage Range from “+16 V dc to +40 V dc” to “+15 V dc to +50 V dc”. Table IA VOUT Load Regulation test; Correct max value from 100 mV for device type 01 and max value 120 mV for device type 02, 03

2、 to max value of 50 mV for all device types. gjc 12-01-18 Charles F. Saffle REV SHEET REV SHEET 15 16 17 18 19 REV STATUS REV OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Greg Cecil DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil COLUMBUS, OHIO 4321

3、8-3990 http:/www.landandmaritime.dla.mil/ THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Charles F. Saffle MICROCIRCUIT, HYBRID, LINEAR, SINGLE CHANNEL, DC-DC CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 11-10-25 AMSC N/A REVISION LEVEL SIZE A CAGE CODE

4、 67268 5962-11218 A SHEET 1 OF 19 DSCC FORM 2233 APR 97 5962-E141-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11218 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 22

5、34 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardne

6、ss assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 P 11218 01 K X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) /

7、Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit funct

8、ion as follows: Device type Generic number Circuit function 01 SVHF283R3S DC-DC Converter, 10 W, +3.3 V Output 02 SVHF2805S DC-DC Converter, 15 W, +5 V Output 03 SVHF2812S DC-DC Converter, 20 W, +12 V Output 04 SVHF2815S DC-DC Converter, 20 W, +15 V Output 05 SVHF282R5S DC-DC Converter, 8 W, +2.5 V

9、Output 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D).

10、The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliabi

11、lity devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic a

12、nd conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document sh

13、ould be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo

14、reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11218 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows

15、: Outline letter Descriptive designator Terminals Package style X See figure 1 8 Dual-in-line Y See figure 1 8 Dual-in-line, flange mount 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input Voltage (Continuous) . +50 V dc Input Voltage (T

16、ransient, 1 second) +80 V dc Power Dissipation (PD, Full Load, TCASE = +125C) . 6 W Output Power (Dependant on Output Voltage) . 20 W Junction Temperature Rise to Case . +12 C Storage Temperature -65 C to +150 C Lead Solder Temperature (10 seconds) . +270 C 1.4 Recommended operating conditions. Inpu

17、t Voltage Range +15 V dc to +50 V dc Case Operating Temperature Range (TC) . -55 C to +125 C 1.5 Radiation features. Maximum total dose available (dose rate = 30 - 300 rad(Si)/s) . 30 krad (Si) 3/ Maximum total dose available (dose rate 10 mrad(Si)/s) LDR: Components: 30 krad (Si) 3/ 4/ Hybrid: 5/ S

18、ingle event phenomenon (SEP) effective linear energy threshold (LET): SEL, SEB, SEGR, SEFI . 44 MeV-cm2/mg 2/ 6/ 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified h

19、erein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL

20、-STD-1835 - Interface Standard for Electronic Component Case Outlines. _ 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Single event performance is tested with minor

21、transients only; no dropouts, shutdowns, latch up or burn out. 3/ Bipolar device types may degrade from displacement damage from radiation which could affect RHA levels. These device types have not been characterized for displacement damage. 4/ Components: The bipolar, BiCMOS linear and mixed signal

22、 semiconductor components have been tested to High Dose Rate (HDR) Condition C (30-300 rad(Si)/s) and Low Dose Rate (LDR) per condition D of MIL-STD-883, method 1019. The difference between HDR and LDR test results has been compared to determine if the semiconductors exhibit ELDRS effect. Low dose r

23、ate sensitivity was not demonstrated. 5/ Hybrid: Hybrid devices have been tested at HDR. LDR testing on the device has not been completed. 6/ See table IB. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-1121

24、8 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps

25、.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM

26、) ASTM F 1192 - Standard Guide for the Measurement of Single Event Phenomena (SEP) Induced by Heavy Ion Irradiation of Semiconductor Devices. 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedenc

27、e. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Complian

28、ce with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performan

29、ce requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, constructio

30、n, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Radiation exposure circuit. Th

31、e radiation exposure circuit shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical te

32、st requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1

33、.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conform

34、ance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made availabl

35、e to the preparing activity (DLA Land and Maritime-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm t

36、hat the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproduc

37、tion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11218 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accorda

38、nce with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall

39、 apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime-VA or the acquiring activity upon request. Also, the test

40、circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA as specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as sp

41、ecified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. c. PIND testing, method 2020, condition A, of MIL-STD-883. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAN

42、DARD MICROCIRCUIT DRAWING SIZE A 5962-11218 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE IA. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ 3/ 4/ 5/ 6/ -55C TC +125C VIN = +28 V dc 5% Full Load unless otherwise specified G

43、roup A subgroups Device type Limits Unit Min Max Output Voltage VOUT IOUT = 3 A 1 01 3.267 3.333 V dc 2,3 3.25 3.35 1,2,3 7/ 3.244 3.35 IOUT = 3 A 1 02 4.95 5.05 2,3 4.925 5.075 1,2,3 7/ 4.89 5.10 IOUT = 1.67 A 1 03 11.88 12.12 2,3 11.82 12.18 1,2,3 7/ 11.66 12.3 IOUT = 1.34 A 1 04 14.85 15.15 2,3 1

44、4.775 15.225 1,2,3 7/ 14.565 15.4 IOUT = 3.2 A 1 05 2.475 2.525 2,3 2.463 2.538 1,2,3 7/ 2.463 2.538 Output Current 8/ 9/ IOUT VIN = 15 V dc to 50 V dc 1,2,3 01,02 3 A 03 1.67 04 1.34 05 3.2 VOUT Ripple Voltage VRIP BW = 20 Hz to 10 MHz 1,2,3 All 40 mVp-p VOUT Line Regulation VRLINE VIN = 15 V dc to

45、 50 V dc 1,2,3 All 20 mV VOUT Load Regulation VRLOAD +VOUT No Load to Full Load 1,2,3 All 50 mV Input Current IIN IOUT = 0, Inhibit = 0 1,2,3 All 6 mA IOUT = 0, Inhibit = open 65 IIN Ripple Current IRIP BW = 20 Hz to 10 MHz 1,2,3 All 80 mAp-p 1 7/ 80 2,3 7/ 110 See footnotes at end of table. Provide

46、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11218 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 TABLE IA. Electrical performance characteristics - Continued. Test

47、 Symbol Conditions 1/ 2/ 3/ 4/ 5/ 6/ -55C TC +125C VIN = +28 V dc 5% Full Load unless otherwise specified Group A subgroups Device type Limits Unit Min Max Efficiency Eff IOUT = 3 A 1,2,3 01 65 % IOUT = 3 A 02 72 IOUT = 1.67 A 03 77 IOUT = 1.34 A 04 78 IOUT = 3.2 A 05 57 Isolation ISO 500 V dc, TC =

48、 +25C 1 All 100 M Capacitive Load 10/ CL No effect on DC performance, TC = +25C 1 01,02, 05 1000 F 03,04 500 Short Circuit Power Dissipation PD Short Circuit 1,2,3 All 8 W Switching Frequency FS 1,2,3 All 350 500 kHz VOUT Step Load Transient VTLOAD 50% Load to 100% Load 4,5,6 01 400 mV pk 02 600 03,04 500 05 250 VOUT Step Load Transient Recovery 11/ TTLOAD 50% Load to 100% Load 4,5,6 01,03, 04 500 s 02, 05 600 VOUT Step Line Transient 10/ VTLINE VIN = 16 V dc