DLA SMD-5962-11231-2011 MICROCIRCUIT HYBRID LINEAR POSITIVE SWITCHING VOLTAGE REGULATOR.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV SHET REV SHET REV STATUS REV OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil COLUMBUS, OHIO 43218-3990http:/www.landandmaritime.dla.mil THIS DRA

2、WING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Charles F. Saffle MICROCIRCUIT, HYBRID, LINEAR, POSITIVE, SWITCHING, VOLTAGE REGULATOR AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 11-09-22 AMSC N/A REVISION LEVEL SIZE A CAGE CODE 67268 5962-11231 SHEET 1 OF 12 DSCC FORM 2

3、233 APR 97 5962-E421-11Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11231 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing docum

4、ents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.

5、2 PIN. The PIN shall be as shown in the following example: 5962 R 11231 01 K X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assuranc

6、e (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type. The device type identify the circuit function as follows: Device type Generic number Circuit fun

7、ction 01 MSK 5044RH Radiation hardened, 3.5 A, switching voltage regulator 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well a

8、s qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This le

9、vel is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming

10、 flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in th

11、e device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product ma

12、y have a limited temperature range. 1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 5 TO-254 with tab, straight leads, glass sealed Y See figure 1 5 TO-254 with tab, leads formed up,

13、 glass sealed Z See figure 1 5 TO-254 with tab, leads formed down, glass sealed Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11231 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 3 DSC

14、C FORM 2234 APR 97 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input voltage (VIN) +16 V dc Output current (IOUT) 4 A Shutdown pin voltage )SHDNV( 7.0 V Junction temperature (TJ) +150C Thermal resistance, junction-to-case at +125C: Forw

15、ard switch . 14.0C/W Catch diode 20.0C/W Storage temperature range -65C to +150C Lead temperature (soldering, 10 seconds) +300C 1.4 Recommended operating conditions. Input voltage range (VIN) +4.5 V dc to +12.8 V dc Case operating temperature range (TC). -55C to +125C 1.5 Radiation features. Maximum

16、 total dose available . 100 Krads (Si) 2/ 3/ 4/ 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents

17、are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outl

18、ines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue,

19、Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific

20、exemption has been obtained. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced

21、 low dose rate effects. Radiation end-point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, method 1019, condition A. Dose rate shall be in accordance with MIL-STD-883, method 1019, condition A. 3/ Bipolar device types may degrade from displacement

22、 damage from radiation which could affect RHA levels. These device types have not been characterized for displacement damage. 4/ See figure 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11231 DLA LAND AN

23、D MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performa

24、nce of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 sh

25、all be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specifi

26、ed in MIL-PRF-38534 and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Radiation exposure circuits. The radiation exposure circuits shall be as specifi

27、ed on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirement

28、s shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor sim

29、ilar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device

30、type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime-V

31、A) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the manufacturers product meets the performance

32、requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in

33、accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ST

34、ANDARD MICROCIRCUIT DRAWING SIZE A 5962-11231 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ 3/ -55C TC+125C unless otherwise specified Group A subgroups Device type Limits Uni

35、t Min MaxFeedback voltage VFB1,2,3 011.19 1.23 V M, D, P, L, R 1 1.18 1.23 Line regulation VRLINE4.3 V VIN 15 V 1,2,3 01 0.5 % Load regulation VRLOAD1 A iOUT 3 A 1,2,3 01 1.0 % Efficiency EFF 1,2,3 0175 % Current limit 4/ ILIM 1,2,3 013.5 A VINsupply current at shutdown IVINSHDNV = 0 V, low power st

36、ate 1,2,3 01 75 A Shutdown threshold voltage VSHDNLow power state 1,2,3 01 0.13 0.60 V Switching frequency SF4 01460 540 kHz M, D, P, L, R 4 420 540 1/ Device types have been characterized through all levels M, D, P, L, R of irradiation and tested to 1.5 times at the R level. Pre and post irradiatio

37、n values are identical unless otherwise specified in table I. When performing post irradiation electrical measurements for any RHA level, TC= +25C. 2/ Unless otherwise specified, VIN= 5.0 V, VOUT= 2.5 V, and IOUT= 1.0 A. 3/ These parts may be dose rate sensitive in a space environment and may demons

38、trate enhanced low dose rate effects. Radiation end-point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, method 1019, condition A. 4/ Output current limit function provides protection from transient overloads, but it may exceed the maximum continu

39、ous rating. Continuous operation in current limit may damage the device. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11231 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 6 DSCC FORM

40、2234 APR 97 Case outline X. Symbol Millimeters InchesMin Max Min Max A - 6.48 - .255 A1 0.76 1.27 .030 .050A2 3.30 3.81 .130 .150 b 0.71 0.81 .028 .032 D 20.57 21.08 .810 .830 E 17.27 17.78 .680 .700E1 8.51 9.02 .335 .355 e 2.54 TYP .100 TYP e1 9.91 10.41 .390 .410 L 12.70 - .500 -L1 13.34 13.84 .52

41、5 .545 L2 2.74 3.25 .108 .128 P 3.81 4.31 .150 .170 S1 3.68 REF .145 REFNOTES: 1. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the

42、inch-pound units shall take precedence. 2. Pin numbers are for reference only. 3. Case outline X weight: 7.6 grams typical. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11231 DLA L

43、AND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 7 DSCC FORM 2234 APR 97 Case outline Y. Symbol Millimeters InchesMin Max Min Max A - 6.48 - .255 A1 0.76 1.27 .030 .050 A2 3.30 3.81 .130 .150 b 0.71 0.81 .028 .032 D 20.57 21.08 .810 .830 E 17.27 17.78 .680 .700 E1 8.51 9.02 .335 .355

44、e 2.54 TYP .100 TYP e1 9.91 10.41 .390 .410 L 4.70 5.46 .185 .215 L1 13.34 13.84 .525 .545 L2 2.74 3.25 .108 .128L3 8.38 - .330 - P 3.81 4.31 .150 .170 S1 3.68 REF .145 REF NOTES: 1. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound units

45、of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall take precedence. 2. Pin numbers are for reference only. 3. Case outline Y weight: 7.6 grams typical. FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reprod

46、uction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11231 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 8 DSCC FORM 2234 APR 97 Case outline Z. Symbol Millimeters InchesMin Max Min MaxA - 6.48 - .255 A1 0.76 1.27 .030 .050A2 3.

47、30 3.81 .130 .150 b 0.71 0.81 .028 .032D 20.57 21.08 .810 .830E 17.27 17.78 .680 .700E1 8.51 9.02 .335 .355e 2.54 TYP .100 TYP e1 9.91 10.41 .390 .410L 4.70 5.46 .185 .215 L1 13.34 13.84 .525 .545L2 2.74 3.25 .108 .128L3 8.38 - .330 -P 3.81 4.31 .150 .170S1 3.68 REF .145 REF NOTES: 1. The U. S. Gove

48、rnment preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall take precedence. 2. Pin numbers are for reference only. 3. Case outline Z weight: 7.6 grams typical. FIGURE 1. Case outlines - Continued. Provided by IHSNot for Res