DLA SMD-5962-11234-2012 MICROCIRCUIT HYBRID LINEAR 500 KHz STEP DOWN SWITCHING REGULATOR CONTROLLER.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV SHEET REV SHEET REV STATUS REV OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Greg Cecil DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mi

2、l THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Tom Hess MICROCIRCUIT, HYBRID, LINEAR, 500 KHz, AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 12-07-11 STEP DOWN, SWITCHING REGULATOR CONTROLLER AMSC N/A REVISION LEVEL SIZE A CAGE CODE 67268 5962-11234 SHEET 1 OF 1

3、4 DSCC FORM 2233 APR 97 5962-E482-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11234 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This

4、 drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected

5、in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 R 11234 01 K X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation har

6、dness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device types. The device types identify the circuit function as follows: Device type Generic nu

7、mber Circuit function 01 MSK 5059RH Radiation hardened, 4.5 A, switching regulator controller 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Cert

8、ification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality c

9、lass level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer

10、 specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must

11、 be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified fl

12、ow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11234 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 3 DSCC FORM 2234 APR 97 Outlin

13、e letter Descriptive designator Terminals Package style X See figure 1 16 Flat pack with straight leads Y See figure 1 16 Flat pack with gull wing leads 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input voltage (VIN) 16 V dc Output curr

14、ent 4.5 A 2/ BOOST voltage 30 V dc BOOST above input voltage 15 V dc Shutdown pin voltage )SHDNV( 7.0 V Feedback pin voltage . 3.5 V dc Feedback pin current . 1 mA Power dissipation (PD) . 14 W Thermal resistance, junction-to-case (TC= +125C) 5.0C/W Junction temperature (TJ) +150C Storage temperatur

15、e -65C to +150C Lead temperature (soldering, 10 seconds) +300C 1.4 Recommended operating conditions. Input voltage range (VIN) 4.3 V dc to 12.8 V dc Case operating temperature range (TC) . -55C to +125C 1.5 Radiation features. Maximum total dose available (dose rate = 50 - 100 rads(Si)/s) 100 krads(

16、Si) 3/ Maximum total dose available (dose rate 10 mrads(Si)/s) LDR: 50 krads(Si) 3/ 4/ 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise sp

17、ecified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Stan

18、dard for Electronic Component Case Outlines. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ The absolute maximum current of 4.5 A applies for duty cycle of 75% or low

19、er. Derate linearly from 4.5 A at 75% duty cycle to 3.375 A at 100% duty cycle. Duty cycle = VOUT/VIN. 3/ The devices on this drawing have not been characterized for Enhanced Low Dose Rate Sensitivity (ELDRS), but have been tested for low dose rates per Method 1019, of MIL-STD-833 condition D for in

20、itial qualification. The devices will be re-tested after design of process changes that can affect RHA response of these devices. 4/ Bipolar device types may degrade from displacement damage from radiation which could affect RHA levels. These device types have not been characterized for displacement

21、 damage. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11234 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List

22、of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precede

23、nce. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requireme

24、nts. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated f

25、or the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form,

26、fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and

27、figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Radiation exposure circuits. The radiation exposure circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the qualifying and acquirin

28、g activity upon request. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test re

29、quirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers v

30、endor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for eac

31、h device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and M

32、aritime-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the manufacturers product meets the per

33、formance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

34、e from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11234 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ 3/ -55C TC +125C unless otherwise specified Group A subgroups Devi

35、ce type Limits Unit Min Max Feedback voltage VFBAll conditions 1,2,3 01 1.19 1.23 V M,D,P,L,R 1/ 1 1.17 1.24 Feedback voltage line regulation VFBLINE4.3 V VIN 15 V 1 01 -0.03 0.03 %/V Feedback input bias current IIBFB1,2,3 01 -0.75 0.75 A M,D,P,L,R 1/ 1 -0.9 -0.9 Switch current limit ILIMITVFB= 1.05

36、 V, VC = open, Duty cycle 50% 1,2,3 01 4.5 8.5 A M,D,P,L,R 1/ 1 4.0 Switch on resistance (VSW/ISW) RESON ISW= 4.5 A 1 01 0.112 2,3 0.132 Maximum switch duty cycle DCMAX VFB= 1.05 V 1 01 89 % 2,3 86 Switching frequency SF 4 01 460 540 kHz 5,6 440 560 M,D,P,L,R 1/ 4 410 540 Switch frequency line regul

37、ation VSWLINE4.3 V VIN 15 V 1,2,3 01 -0.20 0.20 %/V Frequency shifting threshold on FB pin VFREQFBf = 10 kHz 1,2,3 01 0.5 1.0 V Input supply current IINSUPPLY1,2,3 01 5.4 mA Synchronization range SYNC 580 kHz SYNC 1 mHz 7 01 Pass/ Fail See footnotes at end of table. Provided by IHSNot for ResaleNo r

38、eproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11234 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ 3/ -

39、55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Shutdown supply current SHDNI SHDNV = 0 V, VSW = 0 V, VC open 1 01 50 A 2,3 75 Lockout threshold LOKT VC open 1,2,3 01 2.3 2.46 V Shutdown threshold SHDNT VC open, device shutting down 1,2,3 01 0.13 0.60 V Devi

40、ce starting up 0.25 0.7 Synchronization threshold SYNCT 1,2,3 01 2.2 V 1/ Device type 01 has been characterized through all levels M, D, P, L, and R of irradiation. However, device type 01 is tested at 1 times the R level. Pre and post irradiation values are identical unless otherwise specified in t

41、able I. When performing post irradiation electrical measurements for any RHA level, TC= +25C. 2/ Unless otherwise specified VIN= 5 V dc, VC = 1.5 V dc, and BOOST = VIN+ 5 V dc. 3/ Devices from this drawing were tested at low dose rates, condition D, of method 1019 of MIL-STD-883 to 50 Krads(Si) and

42、met all limits. The devices will be re-tested after design or process changes that can affect RHA response of these devices. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11234 DLA LAND AND MARITIME COLUMBU

43、S, OHIO 43218-3990 REVISION LEVEL SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Symbol Millimeters Inches Min Max Min Max A - 2.92 - .115 A1 0.81 1.32 .032 .052 b 0.30 0.46 .012 .018 c 0.20 0.30 .008 .012 D 9.27 9.78 .365 .385 E 12.45 12.95 .490 .510 e 1.27 TYP .050 TYP e1 8.76 9.02 .345 .355 L1 10.

44、16 - .400 - S1 1.91 REF .075 REF NOTES: 1. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall take precedence.

45、 2. Pin numbers are for reference only. 3. Case outline X weight: 1.5 grams typical. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11234 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3

46、990 REVISION LEVEL SHEET 8 DSCC FORM 2234 APR 97 Case outline Y. Symbol Millimeters Inches Min Max Min Max A - 2.92 - .115 A1 0.20 0.46 .008 .018 b 0.30 0.46 .012 .018 c 0.20 0.30 .008 .012 D 9.27 9.78 .365 .385 E 12.45 12.95 .490 .510 D1 13.97 15.24 .550 .600 e 1.27 TYP .050 TYP e1 8.76 9.02 .345 .

47、355 L1 1.27 REF .050 REF L2 1.14 1.40 0.045 0.055 S1 1.91 REF .075 REF NOTES: 1. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the i

48、nch-pound units shall take precedence. 2. Pin numbers are for reference only. 3. Case outline Y weight: 1.5 grams typical. FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11234 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEV