DLA SMD-5962-13219-2013 MICROCIRCUIT HYBRID LINEAR SINGLE CHANNEL DC-DC CONVERTER.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV SHEET REV SHEET REV STATUS REV OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Greg Cecil DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR U

2、SE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Greg Cecil APPROVED BY Charles F. Saffle MICROCIRCUIT, HYBRID, LINEAR, SINGLE CHANNEL, DC-DC CONVERTER DRAWING APPROVAL DATE 13-08-27 AMSC N/A REVISION LEVEL SIZE A CAGE CODE 67268 5962-13219 SHEET 1 OF 10 DSCC FORM 2233 APR

3、97 5962-E270-13Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-13219 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents fiv

4、e product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. T

5、he PIN shall be as shown in the following example: 5962 - 13219 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA)

6、designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type. The device type identify the circuit function as follows: Device type Generic number Circuit function 01

7、 DVPL0510S DC-DC converter, 33 W, 10 A output 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K,

8、and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in ap

9、plications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer g

10、uarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document

11、; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature

12、range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-13219 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline. The case outline are as designated

13、 in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 9 Dual-in-line 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input voltage (continuous) . +5.5 V dc Input voltage (transient, 1

14、second) +5.8 V dc Junction temperature rise above case +15C Storage temperature range . -65C to +150C Lead temperature (soldering, 10 seconds) . +270C 1.4 Recommended operating conditions. Input voltage range . +4.5 V dc to +5.5 V dc Output voltage range . +0.8 V dc to +3.3 V Case operating temperat

15、ure range (TC). -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in

16、 the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT O

17、F DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/quicksearch.dla.mil from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111

18、-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Str

19、esses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING

20、SIZE A 5962-13219 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-3

21、8534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements

22、 as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical

23、 dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherw

24、ise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for

25、each subgroup are defined in table I. 3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general perform

26、ance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parame

27、ters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime-VA) upon request. 3.7 Certificate of compliance. A certificate of complian

28、ce shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance.

29、 A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers

30、Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test cond

31、ition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissi

32、pation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TAas specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tes

33、ts prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-13219 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 5 DSCC FORM 2

34、234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TC +125C VIN= +5.0 V dc 5% full load unless otherwise specified Group A subgroups Device type Limits Unit Min Max Input voltage 2/ VINVOUT= 0.8 V dc to 3.3 V dc 1,2,3 01 4.5 5.5 V dc Output voltage VOUTIOUT= 1

35、0 A 1 01 -1.5 +1.5 %Vout 2,3 -2.5 +2.5 Output current 3/ IOUT1,2,3 01 10 A VOUTripple voltage VRIPBW = 20 Hz to 10 MHz 1,2,3 01 80 mVp-p VOUTload regulation VRLOADNo load to full load 1,2,3 01 60 mV Input current IINIOUT= 0, Inhibit (pin 3) = 0 1,2,3 01 3 mA IOUT= 0, Inhibit (pin 3) = open 80 Effici

36、ency Eff VOUT= 3.3 V dc 1,2,3 01 91 % Isolation ISO 500 V dc, Tc= +25C 1 01 100 M Capacitive load 1/ CLNo effect on DC performance, Tc= +25C 1 01 5000 F Short circuit power dissipation PDShort circuit 1,2,3 01 3 W Switching frequency FS1,2,3 01 240 350 kHz VOUTstep load transient VTLOAD50% load to 1

37、00% load VOUT= 3.3 V dc 4,5,6 01 300 mV pk VOUTstep load transient recovery 4/ TTLOAD50% load to 100% load VOUT= 3.3 V dc 4,5,6 01 160 s Start up overshoot VtonOSVIN= 0 V dc to 5 V dc 4,5,6 01 40 mV pk Start up delay TonDVIN= 0 V dc to 5 V dc 4,5,6 01 8 ms 1/ With 100 F capacitor from VINto ground.

38、2/ Parameter shall be tested as part of device characterization and after design and process changes. Thereafter, parameters shall be guaranteed to the limits specified in table I. 3/ Derate linearly to 0 at TC= +135C. 4/ Time for VOUTto settle within 1 percent of its final value. Provided by IHSNot

39、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-13219 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 6 DSCC FORM 2234 APR 97 Case outline X. FIGURE 1. Case outline Provided by IHSNot for ResaleNo reproduc

40、tion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-13219 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 7 DSCC FORM 2234 APR 97 Case outline X - Continued. Symbol Millimeters Inches Min Max Min Max A 6.86 .270 b1 2.24 2.34 .088 .

41、092 D 27.31 1.075 E 27.31 1.075 E1 18.92 19.18 .745 .755 e 3.89 4.14 .153 .163 e1 7.49 7.75 .295 .305 e2 11.30 11.56 .445 .455 e3 15.11 15.37 .595 .605 e4 18.92 19.18 .745 .755 L 4.70 5.46 .185 .215 S 3.89 4.14 .153 .163 S1 22.94 23.19 .903 .913 b2 .58 .69 .023 .027 b .97 1.07 .038 .042 b3 1.73 1.83

42、 .068 .072 NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference

43、only. 3. Case outline weight: 16 grams maximum. FIGURE 1. Case outline Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-13219 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 8 D

44、SCC FORM 2234 APR 97 Device types 01 Case outlines X Terminal number Terminal symbol 1 +VIN 2 Common 3 Inhibit 4 Track 5 +Sense 6 Trim 7 Common 8 9 +VOUT Case FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MI

45、CROCIRCUIT DRAWING SIZE A 5962-13219 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 9 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters - F

46、inal electrical parameters 1*, 2, 3 ,4 ,5, 6 Group A test requirements 1, 2, 3, 4, 5, 6 Group C end-point electrical parameters 1, 2, 3, 4 End-point electrical parameters for Radiation Hardness Assurance (RHA) devices Not applicable * PDA applies to subgroup 1. 4.3 Conformance and periodic inspectio

47、ns. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance with MIL-PRF-38534 and as specified herein. 4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows: a. Tests shall be as specified in table II herein. b. Subgroups

48、7, 8, 9, 10, and 11 shall be omitted. 4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534. 4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows: a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test, method