DLA SMD-5962-81006 REV J-2005 MICROCIRCUIT LINEAR CMOS HIGH LEVEL ANALOG SWITCHES WITH DRIVERS MONOLITHIC SILICON《硅单片装有驱动器的高电平模拟开关 氧化物半导体线性微型电路》.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED F Add peak current to absolute maximum ratings. Editorial changes throughout. 92-11-24 M. A. FRYE G Changes in accordance with NOR 5962-R144-95. 95-10-20 M. A. FRYE H Make corrections to the switch operation table in 3.3.1. Update boilerplate to re

2、flect current requirements. -rrp 03-03-10 R. MONNIN J Make correction to marking paragraph 3.5. -rrp 05-05-11 R. MONNIN THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. CURRENT CAGE CODE 67268 REV SHET REV SHET REV STATUS REV J J J J J J J J J J J J OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11

3、 12 PMIC N/A PREPARED BY GARY J. ZAHN DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY WILLIAM E. SHARP COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY N. A. HAUCK MICROCIRCUIT, LINEAR, CMOS, HIGH LEVEL ANALOG S

4、WITCHES WITH DRIVERS, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 81-10-01 AMSC N/A REVISION LEVEL J SIZE A CAGE CODE 14933 81006 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E329-05 Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

5、se from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 81006 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordan

6、ce with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 81006 01 X X Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit function as

7、follows: Device type Generic number Circuit function 01 IH5040, DG5140 One-channel, 75 ohms, SPST switch 02 IH5041, DG5141 Two-channel, 75 ohms, SPST switch 03 IH5042, DG5142 One-channel, 75 ohms, SPDT switch 04 IH5043, DG5143 Two-channel, 75 ohms, SPDT switch 05 IH5044, DG5144 One-channel, 75 ohms,

8、 DPST switch 06 IH5045, DG5145 Two-channel, 75 ohms, DPST switch 07 IH5046 One-channel, 75 ohms, DPDT switch 08 IH5047 One-channel, 75 ohms, 4PST switch 09 IH5140, HI5040 One-channel, 75 ohms, SPST switch 10 IH5141, HI5041 Two-channel, 75 ohms, SPDT switch 11 IH5142, HI5042 One-channel, 75 ohms, SPD

9、T switch 12 IH5143, HI5043 Two-channel, 30 ohms, SPDT switch 13 IH5144, HI5044 One-channel, 30 ohms, DPST switch 14 IH5145, HI5045 Two-channel, 75 ohms, DPST switch 15 HI5046 One-channel, 75 ohms, DPDT switch 16 IH5047, HI5047 One-channel, 75 ohms, 4PST switch 17 HI5046A One-channel, 30 ohms, DPDT s

10、witch 18 HI5047A One-channel, 30 ohms, 4PST switch 19 IH5148, HI5048 Two-channel, 30 ohms, SPST switch 20 IH5149, HI5049 Two-channel, 30 ohms, DPST switch 21 IH5150, HI5050 One-channel, 30 ohms, SPDT switch 22 IH5151, HI5051 Two-channel, 30 ohms, SPDT switch 1.2.2 Case outline(s). The case outline(s

11、) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style A GDFP5-F14 or CDFP6-F14 14 Flat pack E GDIP1-T16 or CDIP2-T16 16 Dual-in-line I MACY1-X10 10 Can 2 CQCC1-N20 20 Square leadless chip carrier X CDFP3-F14 14 Flat pack 1.2.3 Lead finish.

12、The lead finish is as specified in MIL-PRF-38535, appendix A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 81006 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 3 DSCC FORM 2234

13、APR 97 1.3 Absolute maximum ratings. V+ - V- 33 V dc V+ - VD30 V dc VD- V-. 30 V dc VD- VS22 V dc VL- V-. 33 V dc VL- VIN30 V dc VL- VR20 V dc VIN- VR. 20 V dc VR- V-. 33 V dc VR- VIN. 2 V dc Current (any terminal except S or D) 30 mA Peak current (source to drain) 80 mA 1/ Storage temperature range

14、. -65C to +150C Lead temperature (soldering, 10 seconds) . +300C Junction temperature (TJ) . +175C Power dissipation, (PD): 2/ Cases A and X at TA= +125C . 350 mW Case E at TA= +125C . 400 mW Case I at TA= +125C 350 mW Case 2 at TA= +125C . 350 mW 1.4 Recommended operating conditions. +VCC+15 V dc -

15、VCC. -15 V dc VR0 V dc VL. 5 V dc Ambient operating temperature range (TA). -55C to +125C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of th

16、is drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL

17、-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. 1/ Pulse at 1 ms, 10 percent duty cycle maximum. 2/ For TA= +100C to +125C, derate linearly at 12 mW/C. Provided by IHSNot for ResaleNo reproduction or networking permitted without li

18、cense from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 81006 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings.

19、(Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text

20、of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in

21、 accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL

22、-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modificati

23、ons shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q” or “QML” certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions.

24、 The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical pe

25、rformance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.3.1 Switch operation. The analog switches listed below are guaranteed to turn “on” with either a “

26、low” input (VR VIL 0.8 V) or “high” input (2.4 V VIH VIL) as specified below (see figure 1). Device types VINChannels ON Channels OFF 2.4 V dc 1 01, 09 0.8 V dc 1 2.4 V dc 1, 2 02, 10, 05, 13, 19 0.8 V dc 1, 2 2.4 V dc 1 2 03, 11, 21 0.8 V dc 2 1 2.4 V dc 1, 2 3, 4 04, 12, 22 0.8 V dc 3, 4 1, 2 2.4

27、V dc 2, 3 1, 4 07, 15, 17 0.8 V dc 1, 4 2, 3 2.4 V dc 1, 2, 3, 4 06, 08, 14, 16, 18, 20 0.8 V dc 1, 2, 3, 4 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. M

28、arking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance

29、to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q” or “QML” certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDAR

30、D MICROCIRCUIT DRAWING SIZE A 81006 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C VCC= 15 V unless otherwise specified Group A subgroups Device type Limits

31、Unit Min Max 1, 3 75 2 1 - 16 150 1, 3 45 VD= -10 V, IS= 10 mA, 2 17 - 22 50 1, 3 75 2 1 - 16 150 1, 3 45 VD= 10 V, IS= -10 mA, 2 17 - 22 50 1, 3 75 VD= -7.5 V, IS= 10 mA, VCC= 10 V 2/ 2 150 1, 3 75 Drain source “ON” resistance RDSVD= 7.5 V, IS= -10 mA, VCC= 10 V 2/ 2 All 150 1/ 2, 3 -200 200 VS= VD

32、= 10 V, See 3.3.1 for VIN1 -2 2 2, 3 -200 200 Channel “ON” leakage current ID(ON)VS= VD= -10 V, See 3.3.1 for VIN1 All -2 2 nA 2, 3 -100 100 VS= -10 V, VD= 10 V, See 3.3.1 for VIN1 -1 1 2, 3 -100 100 Drain “OFF” leakage current ID(OFF)VS= 10 V, VD= -10 V, See 3.3.1 for VIN1 All -1 1 nA 2, 3 -100 100

33、 VS= 10 V, VD= -10 V, See 3.3.1 for VIN1 -1 1 2, 3 -100 100 Source “OFF” leakage current IS(OFF)VS= -10 V, VD= 10 V, See 3.3.1 for VIN1 All -1 1 nA 1, 3 -1 1 Input current, input voltage low IILVIN= 0 V 2 All -10 1 A 1, 3 -1 1 Input current, input voltage high IIHVIN= 2.4 V, 5 V 2 All -1 10 A 1, 3 1

34、0 2 1-8 100 1 200 Positive supply current +ICCVIN= 0 V, 5 V 2, 3 9 - 22 300 A 1, 3 -10 2 1 - 8 -100 1 -200 Negative supply current -ICCVIN= 0 V, 5 V 2, 3 9 - 22 -300 A See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STA

35、NDARD MICROCIRCUIT DRAWING SIZE A 81006 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C VCC= 15 V unless otherwise specified Group A subgroups Devic

36、e type Limits Unit Min Max 1, 3 10 2 1 - 8 100 1 -200 Logic supply current +ILVIN= 0 V, 5 V 2, 3 9 - 22 -300 A 1, 3 -10 2 1 - 8 -100 1 -200 Reference supply current +IRVIN= 0 V, 5 V 2, 3 9 - 22 -300 A 11 375 9 450 10 1 - 8 550 11 450 9 500 Turn-on time tON10 9 - 22 800 ns 11 250 9 250 10 1 - 8 400 1

37、1 350 9 450 Turn-off time tOFF10 9 - 22 600 ns Single channel isolation 2/ VISORL= 100 , f = 100 kHz, VIN= 2 VP-P, CL= 5 pF, TA= +25C 9 All 60 dB Crosstalk between channels 2/ VCTRL= 100 , f = 100 kHz, VIN= 2 VP-P, CL= 5 pF, TA= +25C 9 All 60 dB Charge transfer error 2/ VCTEVIN= 0 V, CL= 10 nF, TA=

38、+25C 9 All 30 mV Break before make time delay 2/ tDTA= +25C 9 03, 04, 07 5 ns Driver input capacitance 2/ CAVIN= 0 V, TA= +25C 9 All 45 pF Switch input capacitance 2/ CISSwitch off, TA= +25C 9 All 60 pF Switch output capacitance 2 COSSwitch off, TA= +25C 9 All 60 pF 1/ The listed resistance limits c

39、orrespond to the following voltage values: 45 and 75 9.25 V, 6.75 V 50 and 150 - 8.50 V, 6.0 V 2/ If not tested, shall be guaranteed to the limits specified in table I herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAW

40、ING SIZE A 81006 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 7 DSCC FORM 2234 APR 97 Device type 01 Device types 01 and 09 Device type 09 only Case outline A Case outline E Case outline I Device type 02 Device types 02 and 10 Device type 19 Case outline A Case out

41、line E Case outline E FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 81006 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 8 DSCC FORM 2234 APR 97 D

42、evice types 02 and 10 Device type 03 Device types 03, 11, and 21 Case outline I Case outline A Case outline E Device type 04 Device types 04, 12, and 22 Case outline A Case outline E Case outline 2 FIGURE 1. Terminal connections Continued. Provided by IHSNot for ResaleNo reproduction or networking p

43、ermitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 81006 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 9 DSCC FORM 2234 APR 97 Device type 05 Device types 05 and 13 Case outline A Case outline E Case outline I Device type 06 Device types 06,

44、14, and 20 Case outline A and X Case outline E Case outline 2 FIGURE 1. Terminal connections Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 81006 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-399

45、0 REVISION LEVEL J SHEET 10 DSCC FORM 2234 APR 97 Device type 07 Device types 07, 15, and 17 Case outline A Case outline E Device type 08 Device types 08, 16, and 18 Case outline A Case outline E FIGURE 1. Terminal connections Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 8