DLA SMD-5962-81020 REV G-2013 MICROCIRCUIT DIGITAL CMOS MONOSTABLE ASTABLE MULTIVIBRATOR MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Table I, minimum pulse width changed to 30 ns -55C, +125C. 84-09-04 N. A. Hauck B Add vendor CAGE 27014. Inactivate device 01DX for new design. Delete vendor CAGE 07263. Editorial changes throughout. 86-03-03 M. A. Frye C Add vendor CAGE 18714. D

2、elete vendor CAGE 31019 and 27014. Technical changes in 1.3 and table I. Change drawing CAGE code to 67268. Change to military drawing format. Editorial changes throughout. 89-06-07 M. A. Frye D Add vendor CAGE 27014. Change vendor CAGE 18714 to 34371. Add device type 02. Technical and editorial cha

3、nges throughout. 92-02-06 M. A. Frye E Change IDDfor device type 01. Change input capacitance CIN. Editorial changes throughout. 94-12-12 Monica L. Poelking F Update the boilerplate to current requirements as specified in MIL-PRF-38535. Editorial changes throughout. jak 06-10-16 Thomas M. Hess G Upd

4、ate boilerplate paragraphs to the current MIL-PRF-38535 requirements. - LTG 13-11-22 Thomas M. Hess CURRENT CAGE CODE 67268 REV SHEET REV SHEET REV STATUS REV G G G G G G G G G G G G OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Herbert L. Baker DLA LAND AND MARITIME COLUMBUS, OHIO

5、 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A CHECKED BY Darrell Hill APPROVED BY C. R. Jackson MICROCIRCUIT, DIGITAL, CMOS, MONOSTABLE/ASTABLE MULTIVIBRATOR, MONOLIT

6、HIC SILICON DRAWING APPROVAL DATE 82-02-24 REVISION LEVEL G SIZE A CAGE CODE 14933 81020 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E048-14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 81020 DLA LAND AND MARITIME

7、 COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN

8、 is as shown in the following example: 81020 01 C A Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 4047B Monostable/Astable multi

9、vibrator 02 4047B Monostable/Astable multivibrator 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line D GDFP1-F14 or CDFP2-F14 14 Flat pack 1.2.3 Lead fini

10、sh. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. 1/ Supply voltage range (VDD): Device type 01 -0.5 V dc to +20 V dc Device type 02 -0.5 V dc to +18 V dc Input voltage range (VIN) -0.5 V dc to VDD + 0.5 V dc Storage temperature range (TSTG) -65C to +150

11、C Maximum power dissipation (PD) 500 mW 2/ Lead temperature (soldering, 10 seconds) . +300C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Junction temperature (TJ) . +175C 1.4 Recommended operating conditions. Supply voltage range (VDD): Device type 01 +3.0 V dc to +18 V dc Device type

12、02 +3.0 V dc to +15 V dc Case operating temperature range (TC) -55C to +125C 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ For TC= +100C to +125C, derate linearly at

13、12 mW/C to 200 mW. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 81020 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specif

14、ication, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-

15、38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit

16、Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). 2.2 Order of precedence. In the event of a conflict be

17、tween the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requireme

18、nts shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certi

19、fication to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. T

20、hese modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physi

21、cal dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.

22、2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shal

23、l apply over the full (case or ambient) operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-

24、PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on th

25、e device. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 81020 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 4 DSCC FORM 2234 APR 97 3.5.1 Certification/compliance mark. A compliance indi

26、cator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A cer

27、tificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacture

28、rs product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. No

29、tification of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required do

30、cumentation. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 81020 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEV

31、EL G SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Test conditions 1/ -55C TC +125C unless otherwise specified Device type VDDGroup A subgroups Limits Unit Min Max Quiescent supply current IDDVIN= 0.0 V or VDD1/ 01 5 V 1, 3 1.0 A 2 30 02 1, 3 5.0 2 150 VI

32、N= 0.0 V or VDD1/ 01 10 V 1, 3 2.0 2 60 02 1, 3 10 2 300 VIN= 0.0 V or VDD1/ 01 15 V 1, 3 4.0 2 120 02 1, 3 20 2 600 VIN= 0.0 V or VDD2/ 01 20 V 1, 3 20 2 600 02 1, 3 100 2 3000 Low level output voltage VOLVIN= 0.0 V or VDD1/ IOL= +1A All 5 V 1, 2, 3 0.05 V VIN= 0.0 V or VDD 1/ IOL= +1A All 10 V 1,

33、2, 3 0.05 VIN= 0.0 V or VDDIOL= +1A All 15 V 1, 2, 3 0.05 High level output voltage VOHVIN= 0.0 V or VDD1/ IOH= -1A All 5 V 1, 2, 3 4.95 V VIN= 0.0 V or VDD 1/ IOH= -1A All 10 V 1, 2, 3 9.95 VIN= 0.0 V or VDDIOH= -1A All 15 V 1, 2, 3 14.95 Low level input voltage VILVO= 0.5 V or 4.5 V All 5 V 1, 2,

34、3 1.5 V VO= 1.0 V or 9.0 V 1/ All 10 V 1, 2, 3 3.0 VO= 1.5 V or 13.5 V All 15 V 1, 2, 3 4.0 High level input voltage VIHVO= 0.5 V or 4.5 V All 5 V 1, 2, 3 3.5 V VO= 1.0 V or 9.0 V 1/ All 10 V 1, 2, 3 7.0 VO= 1.5 V or 13.5 V All 15 V 1, 2, 3 11 See footnotes at end of table. Provided by IHSNot for Re

35、saleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 81020 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Test conditions 1/

36、 -55C TC +125C unless otherwise specified Device type VDDGroup A subgroups Limits Unit Min Max Input current IIN2/ VIN= 0.0 V or VDDAll 20 V 1, 3 0.1 A 2 1.0 Low level output current IOL3/ VO= 0.4 V All 5 V 1 0.51 mA 2 0.36 3 0.64 VO= 0.5 V All 10 V 1 1.3 2 0.9 3 1.6 VO= 1.5 V All 15 V 1 3.4 2 2.4 3

37、 4.2 High level output current IOH3/ VO= 4.6 V All 5 V 1 -0.51 mA 2 -0.36 3 -0.64 VO= 2.5 V 01 5 V 1 -1.6 2 -1.15 3 -2.0 VO= 9.5 V All 10 V 1 -1.3 2 -0.9 3 -1.60 VO= 13.5 V All 15 V 1 -3.4 2 -2.4 3 -4.2 Input capacitance CINVIN= 0.0 V, TC= +25C See 4.3.1c 01 4 7.7 pF 02 7.5 Functional test See 4.3.1

38、d All 7, 8 Pulse width (any input) tw1/ RL= 200 k CL= 50 pF minimum tr= tf= 20 ns 01 5 V 9 1000 ns 10, 11 1500 02 9 1000 10, 11 1500 01 10 V 9 230 10, 11 311 02 9 400 10, 11 400 01 15 V 9 160 10, 11 225 02 9 320 10, 11 320 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction o

39、r networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 81020 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Test conditions 1/ -55C TC +125C unless

40、 otherwise specified Device type VDDGroup A subgroups Limits Unit Min Max Transition time tTHL, tTLHRL= 200 k CL= 50 pF minimum tr= tf= 20 ns 01 5 V 9 10 200 ns 10, 11 15 300 02 9 10 200 10, 11 15 300 01 10 V 1/ 9 2.0 100 10, 11 2.0 150 02 9 2.0 100 10, 11 2.0 150 01 15 V 1/ 9 2.0 80 10, 11 2.0 120

41、02 9 2.0 80 10, 11 2.0 120 Propagation delay time, ASTABLE to OSC out, ASTABLE to OSC out tPHL1, tPLH1RL= 200 k CL= 50 pF minimum tr= tf= 20 ns 01 5 V 9 20 400 ns 10, 11 30 600 02 9 20 400 10, 11 30 600 01 10 V 1/ 9 2.0 200 10, 11 2.0 270 02 9 2.0 200 10, 11 2.0 280 01 15 V 1/ 9 2.0 160 10, 11 2.0 2

42、16 02 9 2.0 160 10, 11 2.0 225 Propagation delay time, ASTABLE to Q, ASTABLE to Q, ASTABLE to Q, ASTABLE to Q tPHL2, tPLH2RL= 200 k CL= 50 pF minimum tr= tf= 20 ns 01 5 V 9 45 900 ns 10, 11 68 1350 02 9 45 900 10, 11 68 1350 01 10 V 1/ 9 2.0 350 10, 11 2.0 473 02 9 2.0 500 10, 11 2.0 700 01 15 V 1/

43、9 2.0 250 10, 11 2.0 338 02 9 2.0 400 10, 11 2.0 560 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 81020 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 8 DS

44、CC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Test conditions 1/ -55C TC +125C unless otherwise specified Device type VDDGroup A subgroups Limits Unit Min Max Propagation delay time, +TRIGGER to Q, + TRIGGER to Q, - TRIGGER to Q, - TRIGGER to Q tPHL3, tPL

45、H3RL= 200 k CL= 50 pF minimum tr= tf= 20 ns 01 5 V 9 60 1200 ns 10, 11 90 1800 02 9 60 1200 10, 11 90 1800 01 10 V 1/ 9 2.0 450 10, 11 2.0 608 02 9 2.0 600 10, 11 2.0 840 01 15 V 1/ 9 2.0 300 10, 11 2.0 405 02 9 2.0 480 10, 11 2.0 670 Propagation delay time, RETRIGGER to Q, RETRIGGER to Q tPHL4, tPL

46、H4RL= 200 k CL= 50 pF minimum tr= tf= 20 ns 01 5 V 9 30 600 ns 10, 11 45 900 02 9 30 600 10, 11 45 900 01 10 V 1/ 9 2.0 300 10, 11 2.0 405 02 9 2.0 300 10, 11 2.0 420 01 15 V 1/ 9 2.0 200 10, 11 2.0 270 02 9 2.0 250 10, 11 2.0 350 Propagation delay time, EXTERNAL RESET to Q, EXTERNAL RESET to Q tPHL

47、5, tPLH5RL= 200 k CL= 50 pF minimum tr= tf= 20 ns 01 5 V 9 30 600 ns 10, 11 45 900 02 9 30 600 10, 11 45 900 01 10 V 1/ 9 2.0 200 10, 11 2.0 270 02 9 2.0 250 10, 11 2.0 350 01 15 V 1/ 9 2.0 140 10, 11 2.0 189 02 9 2.0 200 10, 11 2.0 280 1/ Guaranteed, if not tested, to the specified limits in table

48、I. 2/ At TC= -55C, test is performed with VDD= 18 V. 3/ The IOLand IOHtests are tested 100 percent at TC= +25C and are guaranteed, if not tested, for TC= -55C and TC= +125C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 81020 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 9 DSCC FORM 2234 APR 97 Device types 01 and 02 Case outlines C and D Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14