DLA SMD-5962-83024 REV K-2006 MICROCIRCUIT HYBRID LINEAR 4-CHANNEL OPTICALLY COUPLED ISOLATOR《4通道光耦合隔离器 线性混合微型电路》.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change to military format. Remove approved vendor CAGE 31757. 88-11-08 W. Heckman B Reinstate vendor CAGE 31757. Document updated with editorial changes throughout. Changed to reflect MIL-H-38534 processing. 90-01-10 W. Heckman C Document updated

2、 with editorial changes throughout. Changed to reflect current MIL-H-38534 processing. 90-08-09 W. Heckman D Added case outlines X and Y. Editorial changes throughout 93-08-31 K. A. Cottongim E Changes in accordance with NOR 5962-R032-94. 93-11-12 K. A. Cottongim F Added case outline Z. Rewrite enti

3、re document. 94-04-07 K. A. Cottongim G Changes in accordance with NOR 5962-R001-96. 95-10-10 K. A. Cottongim H Correct generic number added in NOR 5962-R001-96. Update document to current MIL-PRF-38534 requirements. 00-10-13 Raymond Monnin J Correct Descriptive designator for case outline F. Change

4、 CDFP4-P16 to CDFP4-F16. Also update drawing to current boiler plate. gjc 02-07-01 Raymond Monnin K Update drawing. 06-12-07 Raymond Monnin THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. CURRENT CAGE CODE 67268 REV SHEET REV SHEET REV STATUS REV K K K K K K K K K K K K OF SHEETS SHEET 1

5、2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Gary Zahn DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Robert M. Heber P O BOX 3990 COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY William K. Heckman MICROCIRCU

6、IT, HYBRID, LINEAR, 4-CHANNEL, OPTICALLY COUPLED ISOLATOR AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 84-08-10 AMSC N/A REVISION LEVEL K SIZE A CAGE CODE 14933 83024 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E129-07Provided by IHSNot for ResaleNo reproduction or networking permitt

7、ed without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 83024 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL K SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents one product assurance class, class H (high reliability) and a choice of case o

8、utlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). 1.2 PIN. The PIN shall be as shown in the following example: 83024 01 E X Drawing number Device type Case outline Lead finish (see 1.2.1) (see 1.2.2) (see 1.2.3) 1.2.1 Device type(s). The device type(s

9、) identify the circuit function as follows: Device type Generic number Circuit function 01 6N140A, HCPL-6751 4-channel optical coupler 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E CDIP2-T1

10、6 16 Dual-in-line F CDFP4-F Flat pack X See figure 1 16 Dual-in-line Y See figure 1 16 Dual-in-line Z See figure 1 16 Dual-in-line 1.2.3 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Supply voltage (VCC) . -0.5 V dc to +20 V dc 2/ Peak input cu

11、rrent (each channel, 2.0 V). 8/ In applications where dV/dt may exceed 50,000 V/s (such as a static discharge) a series resistor, RCC, should be included to protect the detector ICs from destructively high surge currents. The recommended value is: = k (mA)I 0.6V1RFCC 9/ CMLis the maximum tolerable c

12、ommon mode transient to assure that the output will remain in a low logic state (i.e., VO 0.8 V). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 83024 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVI

13、SION LEVEL K SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Millimeters InchesSymbol Min Max Min MaxA 4.57 .180A1 1.40 1.65 .055 .065b 0.41 0.51 .016 .020c 0.18 0.33 .007 .013D 20.07 20.83 .790 .820e 2.29 2.79 .090 .110E 9.65 9.91 .380 .390E1 8.13 .320L 1.07 1.32 .042 .052R 0.89 1.52 .035 .060NOTES:

14、1. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound shall rule. 2. Pin 1 is indicated by a dot marked on top of the pack

15、age. FIGURE 1. Case outline(s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 83024 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL K SHEET 8 DSCC FORM 2234 APR 97 Case outline Y. Millime

16、ters InchesSymbol Min Max Min MaxA 4.32 .170A1 1.14 1.40 .045 .055b 0.41 0.51 .016 .020c 0.18 0.33 .007 .013D 20.07 20.83 .790 .820e 2.29 2.79 .090 .110eA 7.37 7.87 .290 .310E 8.13 .320Q 0.51 .020S 0.89 1.52 .035 .060NOTES: 1. The U. S. Government preferred system of measurement is the metric SI. Th

17、is item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound shall rule. 2. Pin 1 is indicated by a dot marked on top of the package. FIGURE 1. Case outline(s) - Continued. Provided by IHSNot for ResaleNo

18、reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 83024 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL K SHEET 9 DSCC FORM 2234 APR 97 Case outline Z. Millimeters InchesSymbol Min Max Min MaxA 3.56 .140b 0.89 1.14 .035 .04

19、5c 0.18 0.33 . 007 .013D 20.07 20.83 .790 .820e 2.29 2.79 .090 .110eA 7.37 7.87 .290 .310E 8.13 .320Q 0.51 .020S 0.89 1.52 .035 .060NOTES: 1. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems invol

20、ving conflicts between the metric and inch-pound units, the inch-pound shall rule. 2. Pin 1 is indicated by a dot marked on top of the package. FIGURE 1. Case outline(s) - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCU

21、IT DRAWING SIZE A 83024 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL K SHEET 10 DSCC FORM 2234 APR 97 Device type 01 Case outlines E, F, X, Y, and Z Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Cathode 1 Anode 1 Anode 2 Cathode 2 Cathode 3 Anode 3

22、 Anode 4 Cathode 4 NC GND Output 4 Output 3 Output 2 Output 1 VCCNC FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 83024 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 RE

23、VISION LEVEL K SHEET 11 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters 1 Final electrical parameters 1*, 2, 3, 9 Group A test requirements 1, 2, 3, 4, 9, 10,

24、11 Group C end-point electrical parameters 1, 2, 3 End-point electrical parameters for Radiation Hardness Assurance (RHA) devices Not applicable * PDA applies to subgroup 1. 4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance with

25、 MIL-PRF-38534 and as specified herein. 4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows: a. Tests shall be as specified in table II herein. b. Subgroups 5, 6, 7, and 8 shall be omitted. 4.3.2 Group B inspection (PI). Group B inspection shall

26、 be in accordance with MIL-PRF-38534. 4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows: a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test, method 1005 of MIL-STD-883. (1) Test condition A,

27、B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in

28、accordance with the intent specified in method 1005 of MIL-STD-883. (2) TAas specified in accordance with table I of method 1005 of MIL-STD-883. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 4.3.4 Group D inspection (PI). Group D inspection shall be in accordance

29、 with MIL-PRF-38534. 4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 83024 DEFENSE SUPPLY CENTER COL

30、UMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL K SHEET 12 DSCC FORM 2234 APR 97 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government m

31、icrocircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMDs. All proposed change

32、s to existing SMDs will be coordinated as specified in MIL-PRF-38534. 6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus (DSCC) when a system application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this l

33、ist will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-1081. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone

34、 (614) 692-1081. 6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK-103 and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DSCC-VA and have agreed to this drawing. Provided by IHSNot for ResaleNo reproduction or

35、 networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 06-12-07 Approved sources of supply for SMD 83024 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and Q

36、ML-38534 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-385

37、34. DSCC maintains an online database of all current sources of supply at http:/www.dscc.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 8302401EA 8302401EC 8302401EA 8302401EC 31757 31757 50434 50434 6N140A 6N140A 6N140A/883B#200 6N140A/883B 830

38、2401FC 50434 HCPL-6751 8302401XA 8302401XA 31757 50434 6N140A 6N140A/883B#300 8302401YA 8302401YC 50434 50434 6N140A/883B#100 6N140A/883B#100 8302401ZA 8302401ZC 50434 50434 6N140A/883B#600 6N140A/883B#600 1/ The lead finish shown for each PIN representing a hermetic package is the most readily avai

39、lable from the manufacturer listed for that part. If the desired lead finish is not listed contact the Vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Vendor CAG

40、E Vendor name number and address 31757 Micropac Industries, Incorporated Optoelectronics Division 905 E. Walnut Street Garland, TX 75040-6611 50434 Avago Technologies 350 West Trimble Road San Jose, CA 95131 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-