DLA SMD-5962-84092 REV E-2009 MICROCIRCUIT DIGITAL HIGH SPEED CMOS DUAL 2-LINE TO 4-LINE DECODER MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED C Add vendor CAGE F8859. Add device class V criteria. Correct data limits in paragraph 1.3 and IINtest conditions in table I. Add case outline X. Update boilerplate. - jak 00-09-05 Monica L. Poelking D Correct table II. Update boilerplate to MIL-PR

2、F- 38535 requirements jak. 02-01-16 Thomas M. Hess E Change address. Add JEDEC Standard 7-A reference in paragraphs 2.2 and 4.4.1c. Update boilerplate paragraphs to the current requirements in as specified in MIL-PRF-38535. - jak 09-08-17 Thomas M. Hess CURRENT CAGE CODE 67268 First page of this doc

3、ument has been changed REV SHEET REV SHEET REV STATUS REV E E E E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Greg A. Pitz DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY D. A. DiCenzo COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.

4、mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY N. A. Hauck MICROCIRCUIT, DIGITAL, HIGH SPEED CMOS, DUAL 2-LINE TO 4-LINE DECODER, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 84-10-22 AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 14933 84092 S

5、HEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E427-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84092 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOP

6、E 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available,

7、a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following examples. For device classes M and Q: 84092 01 E A Drawing number Device type Case outline Lead finish (see 1.2.2) (see 1.2.4) (see 1.2.5) For device class V: 5962 - 84092 01

8、V X A Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels

9、and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit funct

10、ion as follows: Device type Generic number Circuit function 01 54HC139 Dual 2-line to 4-line decoder 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as listed below. Since the device class designator has been added after the origi

11、nal issuance of this drawing, device classes M and Q designators will not be included in the PIN and will not be marked on the device. Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in acco

12、rdance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84092 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION

13、 LEVEL E SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line F GDFP2-F16 or CDFP3-F16 16 Flat pack X CDFP4-F16 16 Flat pack2 C

14、QCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range (VI

15、N) -0.5 V dc to VCC+0.5 V dc DC output voltage range (VOUT) . -0.5 V dc to VCC+0.5 V dc Input clamp current (IIK) (VINVCC) . 20 mA Output clamp current (IOK) (VOUTVCC) . 20 mA Continuous output current (IOUT) (VOUT= 0.0 to VCC) 25 mA Continuous current through VCCor GND . 50 mA Storage temperature r

16、ange (TSTG) . -65C to +150C Maximum power dissipation (PD): 500 mW 4/ Lead temperature (soldering, 10 seconds) +260C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C 5/ 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VCC) +2.0 V dc to +6.

17、0 V dc Case operating temperature range (TC) -55C to +125C Input rise or fall time (tr, tf): VCC= 2.0 V 0 to 1000 ns VCC= 4.5 V 0 to 500 ns VCC= 6.0 V 0 to 400 ns 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degr

18、ade performance and affect reliability 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. 4/ For TC= +100C to +125C, derate linearly at 12 mW/C. 5/

19、Maximum junction temperature shall not be exceeded except for allowable short duration burn-in screening conditions in accordance with method 5004 of MIL-STD-883. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84

20、092 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein

21、. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcirc

22、uits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/

23、or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those

24、cited in the solicitation or contract. ELECTRONIC INDUSTRIES ALLIANCE (EIA) JEDEC Standard No. 7-A - Standard for Description of 54/74HCXXXX and 54/74HCTXXXX High-Speed CMOS Devices (Copies of these documents are available online at http:/www.eia.org or from the Electronic Industries Alliance, 2500

25、Wilson Boulevard, Arlington, VA 22201-3834.) 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specifi

26、c exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan

27、 shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, constr

28、uction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connectio

29、ns shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUI

30、T DRAWING SIZE A 84092 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified in figure 4. 3.3 Electrical performance characteristics and postir

31、radiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirement

32、s shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is no

33、t feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall b

34、e in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate

35、 of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to

36、be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PR

37、F-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot

38、of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review fo

39、r device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment f

40、or device class M. Device class M devices covered by this drawing shall be in microcircuit group number 39 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84092 DEFENSE SUPPLY CENT

41、ER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Test conditions 1/ -55C TC +125C Group A subgroups Limits Unit unless otherwise specified Min Max High level output voltage VOHVIN= VIHminimum or VILmaxim

42、um IOH= -20 A VCC= 2.0 V 1, 2, 3 1.9 V VCC= 4.5 V 4.4 VCC= 6.0 V 5.9 VIN= VIHminimum or VILmaximum IOH= -4.0 mA VCC= 4.5 V 1 3.98 2, 3 3.7 VIN= VIHminimum or VILmaximum IOH= -5.2 mA VCC= 6.0 V 1 5.48 2, 3 5.2 Low level output voltage VOLVIN= VIHminimum or VILmaximum IOL= +20 A VCC= 2.0 V 1, 2, 3 0.1

43、 V VCC= 4.5 V 0.1 VCC= 6.0 V 0.1 VIN= VIHminimum or VILmaximum IOL= +4.0 mA VCC= 4.5 V 1 0.26 2, 3 0.40 VIN= VIHminimum or VILmaximum IOL= +5.2 mA VCC= 6.0 V 1 0.26 2, 3 0.40 High level input voltage VIH 2/ VCC= 2.0 V 1, 2, 3 1.5 V VCC= 4.5 V 3.15 VCC= 6.0 V 4.2 Low level input voltage VIL 2/ VCC= 2

44、.0 V 1, 2, 3 0.3 V VCC= 4.5 V 0.9 VCC= 6.0 V 1.2 Input capacitance CINVIN= 0.0 V, TC= +25C, See 4.4.1c 4 10.0 pF Quiescent supply current ICCVIN= VCC or GND VCC= 6.0 V IOUT= 0.0 A 1 8.0 A 2, 3 160.0 Input leakage current IINVIN= VCCor GND VCC= 6.0 V 1 100.0 nA 2, 3 1000.0See footnotes at end of tabl

45、e. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84092 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Co

46、ntinued. Test Symbol Test conditions 1/ -55C TC +125C Group A subgroups Limits Unit unless otherwise specified Min Max Power dissipation capacitance CPDSee 4.4.1c 4 46.0 pF Functional tests See 4.4.1b 7, 8 L H Propagation delay time, mA or mB to mYn tPLH1, tPHL1 3/ TC= +25C CL= 50 pF See figure 4 VC

47、C= 2.0 V 9 175.0 ns VCC= 4.5 V 35.0 VCC= 6.0 V 30.0 TC= -55C and +125C CL= 50 pF See figure 4 VCC= 2.0 V 10, 11 255.0 ns VCC= 4.5 V 51.0 VCC= 6.0 V 44.0 Propagation delay time, output enable, mG to mYn tPLH2, tPHL2 3/ TC= +25C CL= 50 pF See figure 4 VCC= 2.0 V 9 175.0 ns VCC= 4.5 V 35.0 VCC= 6.0 V 3

48、0.0 TC= -55C and +125C CL= 50 pF See figure 4 VCC= 2.0 V 10, 11 255.0 ns VCC= 4.5 V 51.0 VCC= 6.0 V 44.0 Transition time, high to low, low to high tTHL, tTLH 4/ TC= +25C CL= 50 pF See figure 4 VCC= 2.0 V 9 75.0 ns VCC= 4.5 V 15.0 VCC= 6.0 V 13.0 TC= -55C and +125C CL= 50 pF See figure 4 VCC= 2.0 V 10, 11 110.0 ns VCC= 4.5 V 22.0 VCC= 6.0 V 19.0 1/ For a power supply of 5.0 V 10, the worst case output voltages (VOHand VOL) occur for HC at 4.5 V