DLA SMD-5962-86049 REV K-2013 MICROCIRCUIT HYBRID DIGITAL SINGLE CHANNEL DRIVER-RECEIVER.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Page 2, 1.3: Change JA. Page 6, 4.2a(2) and 4.3.2b(2): Change TAto TCfor burn-in and life test. Pages 7 and 8, table I: Add end-point electricals for VTH. Add footnote 2/. 86-10-30 W. Heckman B Made technical changes to table I. Updated drawing f

2、ormat with editorial changes. Added device types 02 through 07. Added cases Y,Z, U, and T. Changed to reflect MIL-H-38534 processing. Device type 01 inactive for new design. Added current CAGE code 67268 to sheet 1. 90-02-09 W. Heckman C Add device type 08. Made technical changes to table I. Change

3、dimensions for case outline Y. Change dimensions for case outline U. Editorial changes throughout. 94-01-14 K. Cottongim D Changes in accordance with NOR 5962-R170-95. 95-07-12 Kendall A. Cottongim E Update drawing boilerplate to most current format. 02-02-25 Raymond Monnin F Rewrite paragraphs 4.2.

4、a.2. and 4.3.3.b.2 to add TC. 04-12-02 Raymond Monnin G Table I, Total current, ICC1-SB, ICC1-25, ICC1-50, ICC1-100 for device type 06; change the maximum limit from 30 mA to 60 mA. (4 places) -gz 07-05-10 Robert M. Heber H Added device type 09. Updated boilerplate paragraphs. -sld 10-01-15 Charles

5、F. Saffle J Updated drawing paragraphs. -sld 11-09-01 Charles F. Saffle K Figure 2; Corrected terminal symbols for pins 15 and 16 from “RX Data out and RX Data out“ to “RX Data in and RX Data in“. -sld 13-01-30 Charles F. Saffle THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED CURRENT CAGE

6、 CODE 67268 REV SHEET REV K K K K K K K SHEET 15 16 17 18 19 20 21 REV STATUS OF SHEETS REV K K K K K K K K K K K K K K SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Donald R. Osborne DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCU

7、IT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY D. A. DiCenzo APPROVED BY N. A. Hauck MICROCIRCUIT, HYBRID, DIGITAL, SINGLE CHANNEL, DRIVER-RECEIVER DRAWING APPROVAL DATE 86-07-30 AMSC N/A REVISION LEVEL K SIZE A CAGE CODE 14933 59

8、62-86049 SHEET 1 OF 21 DSCC FORM 2233 APR 97 5962-E208-13Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86049 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL K SHEET 2 DSCC FORM 2234 APR 97 1.

9、 SCOPE 1.1 Scope. This drawing describes device requirements for class H hybrid microcircuits to be processed in accordance with MIL-PRF-38534 and a choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). 1.2 PIN. The PIN shall be as shown i

10、n the following example: 5962-86049 01 X A Drawing number Device type Case outline Lead finish (see 1.2.1) (see 1.2.2) (see 1.2.3) 1.2.1 Device type(s). The device type(s) shall identify the circuit function as follows: Device type Generic number Circuit function 01 BUS-63105 Single channel driver-r

11、eceiver 02 BUS-63105II, BUS-63106II Low power, single channel driver-receiver 03 1/ ARX2402 Single channel driver-receiver 04 1/ ARX3402 Low power, single channel driver-receiver 05 CT-1487M, BUS-8553, BUS-63100 Single channel driver-receiver 06 NHI-1509 Single channel driver-receiver 07 FC155361 Si

12、ngle channel driver-receiver 08 FC155362 Single channel driver-receiver 09 ACT4402 Low power, single channel driver-receiver 1.2.2 Case outline(s). The case outline(s) shall be as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style T See figure 1

13、24 Flat package U See figure 1 24 Dual-in-line package X See figure 1 24 Dual-in-line package Y See figure 1 24 Dual-in-line package Z See figure 1 24 Dual-in-line package 1.2.3 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1/ The device types 03 and 04 are no longer available

14、. Device type 09 may be evaluated as a possible substitute. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86049 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL K SHEET 3 DSCC FORM 2234 APR 97

15、 1.3 Absolute maximum ratings. 1/ Supply voltage range: VCC(device types 01, 03, 04, 05, 06, 07, 08, and 09) -0.3 V dc to +18 V dc VEE(device types 01, 02, 03, 04, 05, 07, 08, and 09) +0.3 V dc to -18 V dc VCC1. -0.3 V dc to +7 V dc Logic input voltage range -0.3 V dc to VCC1Receiver differential vo

16、ltage . 40 Vp-p Receiver common mode voltage range . -10 V dc to +10 V dc Driver peak output current . 200 mA Power dissipation (PD) at +125C: Device types 01, 05, 07, and 08 . 4 W Device types 02 and 09 2.5 W Device type 03 . 2.2 W Device type 04 1.6 W Device type 06 . 0.585 W Storage temperature r

17、ange -65C to +150C Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ) . +160C Thermal resistance, junction-to-case (JC): Device types 01, 06, 07, and 08 . 8.8C/W Device types 02 and 09 7.0C/W Device type 03 . 47.2C/W Device type 04 88C/W Device type 05 60C/W Thermal resistance,

18、 junction to ambient (JA): Device types 01, 06, 07, 08, and 09 . 38.8C/W Device type 02 . 37.0C/W Device type 03 . 77.2C/W Device type 04 110C/W Device type 05 80C/W 1.4 Recommended operating conditions. Supply voltage range: VCC(device types 01, 03, 04, 05, 06, 07, 08, and 09) +14.25 V dc to +15.75

19、 V dc VEE(device types 01, 02, 03, 04, 05, 07, 08, and 09) -14.25 V dc to -15.75 V dc VCC1. +4.5 V dc to +5.5 V dc Logic input voltage range 0 V dc to +5.0 V dc Receiver differential voltage 30 Vp-p Receiver common mode voltage range . -5.0 V dc to +5.0 V dc Driver peak output current: Device types

20、01, 03, 04, 05, 06, 07, and 08 . 180 mA Device type 02 . 160 mA Serial data rate . 1.0 MHz maximum Junction temperature (TJ) . +150C maximum Case operating temperature range (TC) . -55C to +125C 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operatio

21、n at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86049 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL K SHEET 4 DSCC FORM

22、 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation

23、 or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOO

24、KS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094

25、.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREM

26、ENTS 3.1 Item requirements. The individual item performance requirements for device class H shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designa

27、ted for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the f

28、orm, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 he

29、rein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Waveforms. The waveforms shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are a

30、s specified in table I and shall apply over the full specified operating temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86049 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL

31、 K SHEET 5 DSCC FORM 2234 APR 97 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. T

32、he device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (

33、variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision leve

34、l control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) s

35、ubmitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to th

36、is drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described here

37、in. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and sha

38、ll be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TAor TCas specified in a

39、ccordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction

40、or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86049 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL K SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TC +125C unless otherwis

41、e specified Group A subgroups Device types Limits Unit Min Max Receiver Input level VIDifferential input, pin 15 to pin 16 2/ 4,5,6 All 40 Vp-p Input common mode voltage range VICMIndependent of xfmr or in accordance with MIL-HDBK-1553 2/ 4,5,6 All -5 +5 V(pk) Output low voltage VOL IOL= 16 mA 1,2,3

42、 01,02 0.5 V IOL= 4 mA 03,04,05,06,07,08,09 0.5 Output high voltage VOHIOH= -0.4 mA 1,2,3 01,03,04,05,06,07,08,09 2.5 V 02 2.4 Transmitter Input voltage low VIL3/ 1,2,3 All 0.7 V Input voltage high VIH3/ 1,2,3 All 2 V Input current low IIL VIL= 0.4 V 1,2,3 01,03,05,07,08 -1.6 mA 02 -0.72 0.04 04,06,

43、09 -0.4 Input current high IIH VIH= 2.7 V 1,2,3 01,03,04,05,06,07,08,09 0.04 mA 02 -0.72 0.04 Output voltage VOAcross 35 load 1,2,3 All 6 9 Vp-p Output noise voltage VONAcross 35 load 4,5,6 All 10 mVp-p See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitt

44、ed without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86049 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL K SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specifi

45、ed Group A subgroups Device types Limits Unit Min Max Receiver strobe Input voltage low VSIL3/ 1,2,3 All 0.7 V Input voltage high VSIH3/, in accordance with MIL-HDBK-1553 2/ 1,2,3 All 2 V Input current low ISIL VIL= 0.4 V 1,2,3 01,05, 07,08 -1.6 mA 02 -0.72 0.4 03,06 -0.8 04,09 -0.4 Input current hi

46、gh ISIH VIH= 2.7 V 1,2,3 01,03,04,05,06,07,08,09 0.04 mA 02 -0.72 0.04 Transmitter inhibit Input voltage low VIIL3/ 1,2,3 All 0.7 V Input voltage high VIIH3/ 1,2,3 All 2 V Input current low IIIL VSIL= 0.4 V 1,2,3 01,03,05,07,08 -1.6 mA 02 -0.72 0.04 04,06,09 -0.4 Input current high IIIH VSIH= 2.7 V

47、1,2,3 01,03,04,05,06,07,08,09 0.04 mA 02 -0.72 0.04 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86049 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL K SHEET

48、8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device types Limits Unit Min Max Power supply Total current ICC-SB (Standby mode) 1,2,3 01,07,08 50 mA 03 40 04,09 1 05,06 25 IEE-SB (Standby mode) 1,2,3 01,07,08 50 mA 02 35 03 30 04,09 16.5 05 35 ICC1-SB (Standby mode) 1,2,3 01,07,08 35 mA 02,05 45 03 20 04,09 30 06 60 ICC-25