DLA SMD-5962-86823 REV D-2013 MICROCIRCUIT DIGITAL HIGH-SPEED CMOS QUAD 2-INPUT MULTIPLEXER MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add vendor CAGE 27014 to case outline 2. Change vendor similar part number. Editorial changes to table I. - JT 87-04-01 Nelson A. Hauck B Add case outline “F“ to device type 01. Add vendor CAGE 18324 to case outlines E, F, and 2. Editorial change

2、s throughout. Change current CAGE code. - JEN 88-12-08 Michael A. Frye C Update the boilerplate to the current requirements of MIL-PRF-38535. - jak 07-10-17 Thomas M. Hess D Update boilerplate paragraphs to the current MIL-PRF-38535 requirements. - LTG 13-06-21 Thomas M. Hess REV SHEET REV SHEET REV

3、 STATUS REV D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Jeffery Tunstall DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEP

4、ARTMENT OF DEFENSE AMSC N/A CHECKED BY D. A. DiCenzo APPROVED BY N. A. Hauck MICROCIRCUIT, DIGITAL, HIGH-SPEED CMOS, QUAD 2-INPUT MULTIPLEXER, MONOLITHIC SILICON DRAWING APPROVAL DATE 86-09-30 REVISION LEVEL D SIZE A CAGE CODE 67268 5962-86823 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E453-13 Provide

5、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86823 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for

6、 MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-86823 01 E A Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.

7、2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54HC158 Multiplexer, quad 2-input (inverted output) 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descr

8、iptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line F GDFP1-F16 or CDFP2-F16 16 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. 1/ 2/ Supply voltage ran

9、ge (VCC) . -0.5 V dc to +7.0 V dc DC input voltage range (VIN) . -0.5 V dc to VCC+ 0.5 V dc DC output voltage range (VOUT) -0.5 V dc to VCC+ 0.5 V dc Clamp diode current 20 mA DC output current (per pin) . 25 mA DC VCCor GND current (per pin) 50 mA Storage temperature range (TSTG) -65C to +150C Maxi

10、mum power dissipation (PD) 500 mW 3/ Lead temperature (soldering, 10 seconds) . +260C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Junction temperature (TJ) . +175C 1.4 Recommended operating conditions. Supply voltage range (VCC) . +2.0 V dc to +6.0 V dc Input voltage range (VIN) . 0.0

11、 V to VCCOutput voltage range (VOUT) 0.0 V to VCCCase operating temperature range (TC) -55C to +125C Input rise and fall time (tr, tf): VCC= 2.0 V dc 0 to 1000 ns VCC= 4.5 V dc 0 to 500 ns VCC= 6.0 V dc 0 to 400 ns 1/ Stresses above the absolute maximum rating may cause permanent damage to the devic

12、e. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise specified, all voltages are referenced to ground. 3/ For TC= +100C to +125C, derate linearly at 12 mW/C. Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

13、e from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86823 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a p

14、art of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STAN

15、DARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available

16、 online at http:/quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the

17、 issues of these documents cited in the solicitation or contract. JEDEC SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JESD7 - Standard for Description of 54/74HCXXXXX and 54/74HCTXXXXX Advanced High-Speed CMOS Devices. (Copies of these documents are available online at http:/www.jedec.org or from JEDEC

18、 Solid State Technology Association, 3103 North 10thStreet, Suite 240-S Arlington, VA 22201-2107). 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, super

19、sedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing

20、that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approv

21、al in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ o

22、r “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline

23、. The case outline shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 S

24、witching waveforms. The switching waveforms shall be as specified on figure 4. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86823 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DS

25、CC FORM 2234 APR 97 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements

26、 shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marke

27、d. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to

28、 MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order t

29、o be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the

30、requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for

31、 any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at

32、the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86823 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance

33、 characteristics. Test Symbol Test conditions -55C TC +125C unless otherwise specified 1/ Group A subgroups Limits Unit Min Max High level output voltage VOHVIN= VIHor VILIOH= -20 A VCC= 2.0 V 1, 2, 3 1.9 V VCC= 4.5 V 4.4 VCC= 6.0 V 5.9 VIN= VIHor VILIOH= -4.0 mA VCC= 4.5 V 3.7 VIN= VIHor VILIOH= -5

34、.2 mA VCC= 6.0 V 5.2 Low level output voltage VOLVIN= VIHor VILIOL= +20 A VCC= 2.0 V 1, 2, 3 0.1 V VCC= 4.5 V 0.1 VCC= 6.0 V 0.1 VIN= VIHor VILIOL= +4.0 mA VCC= 4.5 V 0.4 VIN= VIHor VILIOL= +5.2 mA VCC= 6.0 V 0.4 High level input voltage VIH2/ VCC= 2.0 V 1, 2, 3 1.5 V VCC= 4.5 V 3.15 VCC= 6.0 V 4.2

35、Low level input voltage VIL2/ VCC= 2.0 V 1, 2, 3 0.3 V VCC= 4.5 V 0.9 VCC= 6.0 V 1.2 Input capacitance CINVIN= 0.0 V, TC= +25C See 4.3.1c 4 10 pF Quiescent supply current ICCVCC= 6.0 V VIN= VCCor GND 1, 2, 3 160 A Input leakage current IINVCC= 6.0 V VIN= VCCor GND 1, 2, 3 1.0 A Functional tests See

36、4.3.1d 7, 8 Propagation delay time, data to output Y tPHL1, tPLH13/ TC= +25C CL= 50 pF See figure 4 VCC= 2.0 V 9 140 ns VCC= 4.5 V 28 VCC= 6.0 V 24 TC= -55C and +125C CL= 50 pF See figure 4 VCC= 2.0 V 10, 11 210 VCC= 4.5 V 42 VCC= 6.0 V 36 See footnotes at end of table. Provided by IHSNot for Resale

37、No reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86823 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Test conditions

38、 -55C TC +125C unless otherwise specified 1/ Group A subgroups Limits Unit Min Max Propagation delay time, select to output Y tPHL2, tPLH23/ TC= +25C CL= 50 pF See figure 4 VCC= 2.0 V 9 160 ns VCC= 4.5 V 32 VCC= 6.0 V 27 TC= -55C and +125C CL= 50 pF See figure 4 VCC= 2.0 V 10, 11 240 VCC= 4.5 V 48 V

39、CC= 6.0 V 41 Propagation delay time, output enable to output Y tPHL3, tPLH33/ TC= +25C CL= 50 pF See figure 4 VCC= 2.0 V 9 160 ns VCC= 4.5 V 32 VCC= 6.0 V 27 TC= -55C and +125C CL= 50 pF See figure 4 VCC= 2.0 V 10, 11 240 VCC= 4.5 V 48 VCC= 6.0 V 41 Transition time tTHL, tTLH3/ TC= +25C CL= 50 pF Se

40、e figure 4 VCC= 2.0 V 9 75 ns VCC= 4.5 V 15 VCC= 6.0 V 13 TC= -55C and +125C CL= 50 pF See figure 4 VCC= 2.0 V 10, 11 110 VCC= 4.5 V 22 VCC= 6.0 V 19 1/ For a power supply of 5 V 10 percent the worst case output voltage (VOHand VO!) occur for HCat 4.5 V. Thus the 4.5 V values should be used when des

41、igning with this supply. Worst case VIHand VILoccur at VCC= 5.5 V and 4.5 V respectively (The VIHvalue at 5.5 V is 3.85 V). The worst case leakage current (IIN, ICC, and IOZ) occur for CMOS at the higher voltage and so the 6.0 V values should be used. Power dissipation capacitance (CPD), typically 4

42、0 pF, determines the no load dynamic power consumption, PD= CPD VCC2f + ICCVCC,and the no load dynamic current consumption, IS = CPD VCCf + ICC. 2/ Test not required if applied as a forcing function for VOHor VOL. 3/ AC testing at VCC= 2.0 V and VCC= 6.0 V shall be guaranteed, if not tested, to the

43、specified parameters. 4/ Transition time (tTLH,tTHL), if not tested, shall be guaranteed to the specified parameters. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86823 DLA LAND AND MARITIME COLUMBUS, OHIO

44、 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 Device type 01 Case outline E and F 2 Terminal number Terminal symbol Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Select A0 B0 Y0 A1 B1 Y1 GND Y2 B2 A2 Y3 B3 A3 Output enable VCC- - - - - - - - - - - - NC Select A0 B0

45、Y0 NC A1 B1 Y1 GND NC Y2 B2 A2 Y3 NC B3 A3 Output enable VCCNC = No internal connection FIGURE 1. Terminal connections. Output enable Select Data inputs Output A B Y H X X X H L L L X H L L H X L L H X L H L H X H L FIGURE 2. Truth table. Provided by IHSNot for ResaleNo reproduction or networking pe

46、rmitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86823 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

47、-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86823 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 9 DSCC FORM 2234 APR 97 FIGURE 4. Switching waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRA

48、WING SIZE A 5962-86823 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 10 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of