DLA SMD-5962-86843 REV D-2013 MICROCIRCUIT DIGITAL ADVANCED LOW-POWER SCHOTTKY TTL INVERTERS MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add figure 3. Change tPHL, tPLH, and footnotes in table I. Editorial changes throughout. Add CAGE #04713. Change in power dissipation and 1/ of paragraph 1.3. Change in test conditions of IIH, IIL, ICCH, and ICCL. Change in IILand VICof Table I.

2、88-05-23 M. A. Frye B Changes in accordance with NOR 5962-R099-92. 92-07-07 Monica Poelking C Redraw with changes. Update to current requirements. Editorial changes throughout. - gap 06-01-23 Raymond Monnin D Update drawing to current MIL-PRF-38535 requirements. -jt 13-03-07 C. SAFFLE THE ORIGINAL F

3、IRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Monica L. Poelking DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS

4、AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Ray Monnin APPROVED BY Michael A. Frye MICROCIRCUIT, DIGITAL, ADVANCED LOW-POWER SCHOTTKY TTL, INVERTERS, MONOLITHIC SILICON DRAWING APPROVAL DATE 87-07-27 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-

5、86843 SHEET 1 OF 9 DSCC FORM 2233 APR 97 5962-E290-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86843 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SC

6、OPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-86843 01 D X Drawing number Device

7、type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device types. The device types identify the circuit function as follows: Device type Generic number Circuit function 01 54ALS04 Hex, one-input inverter gate 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-183

8、5 and as follows: Outline letter Descriptive designator Terminals Package style D GDFP1-F14 or CDFP2-F14 14 Flat package 2 CQCC1-N20 20 Square chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage range . -0.5 V dc

9、minimum to 7.0 V dc maximum Input voltage range -1.2 V dc at -18 mA to 7.0 V dc Storage temperature range . -65C to +150C Maximum power dissipation (PD) 1/ 24.2 mW Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Junction temperature (TJ) +175

10、C 1.4 Recommended operating conditions. Supply voltage range (VCC) . +4.5 V dc minimum to +5.5 V dc maximum Minimum high level input voltage (VIH) 2.0 V dc Maximum low level input voltage (VIL): TC= +125C . 0.7 V dc TC= -55C 0.8 V dc TC= +25C . 0.8 V dc Case operating temperature range (TC) -55C to

11、+125C _ 1/ Maximum power dissipation is defined as VCCx ICC, and must withstand the added PDdue to short circuit test, e.g., IO. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86843 DLA LAND AND MARITIME COL

12、UMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issu

13、es of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standar

14、d Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order

15、 Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and reg

16、ulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualifi

17、ed Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF

18、-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in

19、 accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be

20、 in accordance with 1.2.2 herein. 3.2.2 Terminal connections and logic diagram. The terminal connections shall be as specified on figure 1. 3.2.3 Truth tables. The truth tables shall be as specified on figure 2. 3.2.4 Switching waveforms and test circuit. The switching waveforms and test circuit sha

21、ll be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test

22、requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86843 DLA LAND AND MARITIME COLUMBUS

23、, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD

24、 PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indi

25、cator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in

26、MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conform

27、ance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Veri

28、fication and review. DLA Land and Maritime, DLA Land and Maritime s agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 4. VERIFICATION 4.

29、1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additiona

30、l criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shal

31、l specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter te

32、sts prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86843 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FOR

33、M 2234 APR 97 TABLE I. Electrical performance characteristics. 1/ 2/ Test Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroups Limits Unit Min Max High level output voltage VOHVIH= 2.0 V, VCC= 4.5 V, IOH= -0.4 mA 3/ VIL= 0.8 V 1, 3 2.5 V VIL= 0.7 V 2 Low level output voltage

34、VOLVIH= 2.0 V, VCC= 4.5 V, IOL= 4.0 mA 4/ VIL= 0.8 V 1, 3 0.4 V VIL= 0.7 V 2 Input clamp voltage VICVCC= 4.5 V, IIN= -18 mA 1, 2, 3 -1.2 V High level input current IIH1VCC= 5.5 V, VIN= 2.7 V, All other inputs = 0.0 V 1, 2, 3 20 A IIH2VCC= 5.5 V, VIN= 7.0 V, All other inputs = 0.0 V 1, 2, 3 100 A Low

35、 level input current IILVCC= 5.5 V, VIN= 0.4 V, All other inputs = 4.5 V 1, 2, 3 -0.1 mA Output current IOVCC= 5.5 V, VOUT= 2.25 V 4/ 1, 2, 3 -20 -112 mA High level supply current ICCHVCC= 5.5 V, VIN 0.4 V (All inputs) 1, 2, 3 1.1 mA Low level supply current ICCLVCC= 5.5 V, VIN 4.5 V (All inputs) 1,

36、 2, 3 4.4 mA Functional tests See 4.3.1c 5/ 7, 8 Propagation delay time any input to Y tPLHVCC= 4.5 V to 5.5 V, CL= 50 pF, RL= 500 6/ See figure 3 9, 10, 11 1 9 ns tPHL9, 10, 11 2 14 ns 1/ Unused inputs that do not directly control the pin under test must be 2.5 V or 0.4 V. 2/ The inputs shall not e

37、xceed 5.5 V or go less than 0.0 V. No inputs shall be floated. 3/ All outputs must be tested. In the case where only one input at VILmaximum or VIHminimum produces the proper output state, the test must be performed with each input being selected as the VILmaximum or VIHminimum input. 4/ The output

38、conditions have been chosen to produce a current that closely approximates one-half of the true short circuit output current, IOS. Not more than one output will be tested at a time and the duration of the test condition shall not exceed 1 second. 5/ Functional tests shall be conducted at input test

39、conditions of 0.0 V VIL VOLand VOH VIH VCC. 6/ Propagation delay limits are based on single output switching. Unused inputs = 3.5 V or 0.3 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86843 DLA LAND AND

40、 MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 FIGURE 1. Terminal connections and logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86843 DLA LAND AND MARITIME

41、 COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 Truth table (each gate) Input A Output Y L H H L Positive logic Y = A L = Low level voltage H = High level voltage FIGURE 2. Truth table. NOTES: 1. CL includes probe and jig capacitance. 2. All input pulses have the following

42、characteristics: PRR 10MHz, duty cycle = 50%, tr= tf= 3 ns 1 ns. 3. The outputs are measured one at a time with one input transition per measurement. FIGURE 3. Switching waveforms and test circuit. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAN

43、DARD MICROCIRCUIT DRAWING SIZE A 5962-86843 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical paramet

44、ers (method 5004) - - - Final electrical test parameters (method 5004) 1*, 2, 3, 7, 8, 9, 10, 11 Group A test requirements (method 5005) 1, 2, 3, 7, 8, 9, 10, 11 Groups C and D end-point electrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroup 1. 4.3 Quality conformance inspection. Qual

45、ity conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 4, 5, and 6 in table I, method 5005

46、of MIL-STD-883 shall be omitted. c. Subgroups 7 and 8 shall include verification of the truth table. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A,

47、B, C or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance w

48、ith the intent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86843 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 9 DSCC FORM 2234 APR 97 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with