DLA SMD-5962-86851 REV B-1992 MICROCIRCUITS DIGITAL BIPOLAR 8-BIT I O PORT MONOLITHIC SILICON《硅单块 8比特输入输出口 双极数字微型电路》.pdf

1、SMD-5962-Bb53 REV B W b 0032823 1Tb m DATE (YYHHDD) NOTICE OF REVISION (NOR) (See MIL-STD-480 for instructions) 92/12/06 his revision described below has been authorized for the document listed. Form Approved OMB NO. 0704-0188 ublic reporting burden for this collection is estimated to average 1 hour

2、 per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing :he collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, in

3、cluding suggestions for reducing this burden, to Washington Headquarters Services, Directorate for :nformation Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302, and to the Office jf Information and Regulatory Affairs, Office of Management and Budget, Washing

4、 2. CAGE CODE 67268 4. CAGE CODE 67268 7. REVISION LETTER (Current) REV A I. ORIGINATOR WE AND ADDRESS Defense Electronics Supply Center Dayton, Ohio 45444-5277 3. NOR NO. 5962-R032-93 5. WCUHENT No. 5W-86851 (New) E 5. TITLE OF DOCMEW HICROCIRCUITS, DIGITAL BIPOLAR add “8“ Revisions description col

5、umn; add “Changes in accordance with Revisions date column; add “92-12-04“. Revision level block; add “B“. Revision status of sheet; for sheet 1 Change from: NOR 5962-R032-93. Sheet 6: Group A I Limits I Unit subgroups I I - I Min I flax I 9 151 I ns 10 , 11 I 20 I I to: I GrouD A I Limits I Unit1 i

6、 I j subg;.oups j i I I Min I Max I Revision Level block; add “8“. 11. THIS SECTION FOR MVERMIENT USE ONLY a. CHECK ONE XJEXISTING DOCUMENT SUPPLEMENTED CUSTODIAN OF MASTER DOCUMENT BY THIS NOR MAY BE USED IN MANUFACTURE. MAY INCORPORATE THIS CHANGE. FURNISH REVISED DOCUMENT TO: 1 REVISED DOCUMENT M

7、UST BE RECEIVED BEFORE MANUFACTURER SHALL MAKE ABOVE REVISION AND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- LTR - A Fsa -33 SND-5962-8b85L REV B 9997996 0032822 032 W DESCRIPTION Tab1 e I, change tOD2. Editorial changes throughout. MIE (YRIUO-

8、DA) 1988 NOV 7 APPROVED STANDARDIZED MILITARY DRAWING MIS DRAWING IS AVAILABLE FOR USE BY ALL DEPAmEMC AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC NIA PREPARED BY DEFENSE ELECfRONICS SUPPLY CENTER DATTON, OHIO 45444 MICROCIRCUITS, DIGIT PORT, MONOLITHIC SILICON 15 APRIL 1988 A I 67268 15962-86851

9、 REVISION LEVEL I A I SHEET 1 OF 19 DESC FORM 193 * U.S. PRiW OFFKC: 1987 - 74612916091 1 CCD R7 JLI u, DISTRIBUTION STATEMENT A. Approved for public release; dlctrlbullon Is unlimited. 5962-El 003 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1. S

10、COPE 1.1 Scope. This drawing describes device requirements for class B microcircuits in accordance nith 1.7Tf MIL-STD-883, “Provisions for the use of MIL-STD-883 in conjunction with compliant non-JAN devices“, 1.2 Part number. The complete part nuinber shall be as shown in the following example: 596

11、2-86851 -I- o1 X X 1 T- -I- I I I I Drawing number Device t pe Case outline Lead finish per (1.d (1.2.2) MIL-M-38510 1.2.1 Device type. The device type shall identify the circuit function as follows: Device type Generic number Circuit function o1 8x376 Programnable addressable bidirectional asynchro

12、nous 1/0 port 1.2.2 Case outline. The case outline shall be as designated in appendix C of MIL-M-38510, and 1s follaws: Outline letter X Case outline D-11 (24-lead, 1.250“ x .410“ x ,225“) dualLi n-1 irk packag 1.3 Absolute maximum ratings. Supply voltage range L/ - - - - - - - - - - - - Storage tem

13、perature range - - - - - - - - - - - Maximum power dissipation (p0) g/ - - - - - - - Thermal resistance, junction-to-case (jc) - - - Case X - - - - - - - - - - - - - - - - - - - - +7.0 V dc maximum . *5.5 V c maximum -65C to f150“C ,825“W +ao c (See MIL-M-38510, appendix C) Input voltage - - i - - -

14、 - i - - - - - - - - - Lead temperature soldering, 10 seconds) - - - - Junction temperature (TJ) - - - - - - - - - - - 150C 1.4 Recommended operating conditions. supply voltage (Vcc) - - - - - - - - - - - - - - Case operating enperature range (TC) - - - - - Minimum high level ihput voltage A - - - -

15、 - - - Maximum low level input voltage - - - - - - - - 4.5 V dc to 5.5 V dc -55C to +125“C 2.0 Y dc 0.8 V dc - 1/ Not appricable during address programing. - 2/ Must withstand the added PD due to short circuit test, e.g., 10s. SIZE A . _. 5962-86851 o respond to any address within a range o $0 t “8

16、1p level (2.0 VI input on the corresponding IV pin (a logical O to :he microcontroller), the counterpart UD-Eus pin must be pulsed according to table III and the 01 1 owing procedures : a. Set all control inputs to the inactive state. UTt: = UC = FE = Vcc and SC = WC = MCLK = GND; leave the UD and b

17、. Increase Vcc to Vccp. c. After Vcc has stabilized, apply a single programing pulse to the ucer-bus bit that corresponds to the desired hfgh-level TV address bit, The 1/0 Ort is programed from the user bus (UDO-UD7) for addressing from the microcontroller bus 5.25 Y I 1 I1.OIs I I I III I i Program

18、ing voltage I III I I Address I I 8.751 9.251 Y I I Protect 1 I 8.751 9.251 1 I I I I i Programming current I III 1 I Address I 1 151mA I I Protect I I 150 I I I Programing pulse rise time I III I I Address ltr I 10 i IO0 I WS I I Protect I 10 I 100 I J I I I I I I Programing pulse width Itw 10.5 I

19、1.0 I ms I I III I I 1 SIZE A 5962-86851 SKANDARDfZED MILTTAW DRAWING EFENS& ELECTRONICS SUPPLY CENTER SHEET DAm,CmK)45444 18 ESC FORM 193A SEP 87 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- SMD-5962-8b51 REV B W 9999996 0032840 058 6.5 Approved

20、 source of supply. An approved source of supply is listed herein, Additional sources will be added as they become available. The vendor listed herein has agreed to this drawing and a certfficate of cmpliance (see 3.5 hereln) has been submitted to DESC-ECS. I Mili tary drawing I v endor I Vendor I pa

21、rt number I CAE I similar part 1 I I number I number i/ I I I I I -1 I 5962-86851lXX I 18324 I 8X376/BXX I I I 1 I I I I I I I I I I I I I I i/ Caution. Do not use this number for item - -tion. Items acquired to this number may not satisfy the performance requirements of this drawing . Vendor CAGE n

22、umber 18324 Vendor name and address Signetics Corporation 4130 South Market Court Sacramento, CA 95834 STANDARDIZED SIZE MILITARY DRAWING A 5962-86851 REVISION LEVEL SHEET DEFENSE UECTRONICS SUPPLY CENTER MYTON, OHIO 45444 19 *U.8.QOVERNMENPRHITINGOF$+SP17 :SC FORM 193A iEP 87 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-