DLA SMD-5962-86857 REV B-2010 MICROCIRCUIT DIGITAL HIGH SPEED CMOS 8-BIT MAGNITUDE COMPARATOR WITH TTL COMPATIBLE INPUTS MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update boilerplate to MIL-PRF-38535 requirements. Editorial changes throughout. - LTG 03-03-11 Thomas M. Hess B Update test condition for high level output voltage (VOH) and low level output voltage (VOL) in table I. Update boilerplate paragraphs

2、 to MIL-PRF-38535 requirement. - jak 10-03-08 Thomas M. Hess CURRENT CAGE CODE 67268 REV SHET REV SHET REV STATUS REV B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Greg A. Pitz DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MI

3、CROCIRCUIT DRAWING CHECKED BY D. A. DiCenzo THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Mike A. Frye MICROCIRCUIT, DIGITAL, HIGH SPEED CMOS, 8-BIT MAGNITUDE COMPARATOR WITH TTL COMPATIBLE INPUTS, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE

4、87-01-02 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 14933 5962-86857 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E094-10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86857 DEFENSE SUPPLY CENTER COLUMBUS COLUM

5、BUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as

6、 shown in the following example: 5962-86857 01 R A Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54HCT688 8-bit magnitude comparato

7、r with TTL compatible inputs 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line package 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535

8、, appendix A. 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to VCC+ 0.5 V dc DC output voltage range (VOUT) . -0.5 V dc to VCC+ 0.5 V dc Clamp diode current 20 mA DC output current (per pin) 25 mA DC VCCor GND current (per p

9、in) . 50 mA Storage temperature range (TSTG) . -65C to +150C Maximum power dissipation (PD) 2/ . 500 mW Lead temperature (soldering 10 seconds) . 260C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) 175C 1.4 Recommended operating conditions. Supply voltage rang

10、e (VCC) +4.5 V dc to +5.5 V dc Case operating temperature range (TC) . -55C to +125C Input rise or fall time: VCC= 4.5 V . 0 to 500 ns 1/ Unless otherwise specified, all voltages are referenced to ground. 2/ For TC= +100C to +125C, derate linearly at 12 mW/C. Provided by IHSNot for ResaleNo reproduc

11、tion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86857 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The follow

12、ing specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, G

13、eneral Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircui

14、t Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing

15、and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with

16、 MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may b

17、e processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not af

18、fect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, con

19、struction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table

20、shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Timing waveforms. The timing waveforms shall be as specified on figure 4. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICR

21、OCIRCUIT DRAWING SIZE A 5962-86857 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall a

22、pply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appen

23、dix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of no

24、t marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-P

25、RF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to

26、listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot o

27、f microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535, appendix A. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility a

28、nd applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86857 DEFENSE SUPPLY CENTER COLUMBUS

29、 COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TC+125C 4.5 V dc VCC 5.5 V dc unless otherwise specified Group A subgroups Device type Limits Unit Min Max High level output voltage VOHVIH= 2.0V

30、or VIL= 0.8 V VCC= 4.5 V IOH = -20 A 1, 2, 3 All 4.4 V IOH = -4.0 mA 3.7 Low level output voltage VOLVIH= 2.0V or VIL= 0.8 V VCC= 4.5 V IOL= +20 A 1, 2, 3 All 0.1 V IOL = +4.0 mA 0.4 High level input voltage VIH4.5 V VCC 5.5 V 1, 2, 3 All 2.0 V Low level input voltage VIL4.5 V VCC 5.5 V 1, 2, 3 All

31、0.8 V Input leakage current IINVCC= 5.5 V; VIN= VCCor GND 1, 2, 3 All -1.0 +1.0 A Quiescent current ICC VCC= 5.5 V; VIN= VCCor GND 1, 2, 3 All 160 A Additional quiescent supply current ICCAny 1 input, VIN= 2.4 V or 0.5 V, Other inputs, VIN= VCCor GND VCC= 5.5 V IOUT= 0.0 A 1, 2, 3 All 1.8 mA Input c

32、apacitance CINVIN= 0.0 V, TC= +25C See 4.3.1c 4 10 pF Functional tests See 4.3.1d 7 All L H Propagation delay time, A or B to output tPHL1, tPLH1VCC= 5.0 V 10% CL= 50 pF 10%- See figure 4 9 All 35 ns 10, 11 53 Propagation delay time, output enable to any output tPHL2, tPLH29 All 24 ns 10, 11 36 Outp

33、ut transition time 2/ tTHL, tTLH9 All 15 ns 10, 11 22 1/ For a power supply of 5.0 V 10%, the worst case output voltages (VOHand VOL) occur for HCT at 4.5 V. Thus, the 4.5 V values should be used when designing with this supply. Worst case VIHand VILoccur at VCC= 5.5 V and 4.5 V, respectively. 2/ Tr

34、ansition times, if not tested, shall be guaranteed to the specified parameters. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86857 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B

35、SHEET 6 DSCC FORM 2234 APR 97 Device type 01 Case outline R Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 E A0 B0 A1 B1 A2 B2 A3 B3 GND A4 B4 A5 B5 A6 B6 A7 B7 Y VCCFIGURE 1. Terminal connections. Inputs Output A,B E Y A=B L L AB L H X H H H = High voltage level

36、L = Low voltage level X = Irrelevant FIGURE 2. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86857 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 22

37、34 APR 97 FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86857 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 FIGURE 4. Timin

38、g waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86857 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and insp

39、ection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall ap

40、ply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the input

41、s, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-i

42、n are optional at the discretion of the manufacturer. TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) 1 Final electrical test parameters (method 5004) 1*, 2, 3, 9 Group

43、A test requirements (method 5005) 1, 2, 3, 4, 7, 9, 10, 11 Groups C and D end-point electrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroup 1. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B

44、, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 5, 6, and 8 in table I, method 5005 of MIL-STD-883 shall be omitted. c. Subgroup 4 (CINmeasurement) shall be measured only for the initial

45、test and after process or design changes which may affect input capacitance. d. Subgroup 7 shall include verification of the truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86857 DEFENSE SUPPLY C

46、ENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 10 DSCC FORM 2234 APR 97 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D.

47、The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the int

48、ent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, an