DLA SMD-5962-86884 REV C-2011 MICROCIRCUIT DIGITAL HIGH SPEED CMOS 3-TO-8 LINE DECODER DEMULTIPLEXER MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add case outline 2. Add vendor CAGE 01295. Changes to figure 1, table I, and page 6. 87-11-03 R. P. Evans B Add notes and test circuit in figure 4. Update boilerplate to MIL-PRF-38535 requirements. Editorial changes throughout. LTG05-01-13 Thomas

2、 M. Hess C Update boilerplate paragraphs to the current MIL-PRF-38535 requirements. - LTG 11-08-25 Thomas M. Hess CURRENT CAGE CODE 67268 REV SHET REV SHET REV STATUS REV C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Greg A. Pitz DLA LAND AND MARITIME COLUMBUS, OHIO 4

3、3218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A CHECKED BY D. A. DiCenzo APPROVED BY N. A. Hauck MICROCIRCUIT, DIGITAL, HIGH-SPEED CMOS, 3-TO-8 LINE DECODER/DEMULTIPLEXER

4、, MONOLITHIC SILICON DRAWING APPROVAL DATE 87-02-10 REVISION LEVEL C SIZE A CAGE CODE 14933 5962-86884 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E464-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86884 DL

5、A LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN

6、). The complete PIN is as shown in the following example: 5962-86884 01 E A Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54HC238 3

7、-to-8 line decoder/demultiplexer 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line 2 CQCC1-N20 20 Square chip carrier 1.2.3 Lead finish. The lead finish i

8、s as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to VCC+ 0.5 V dc DC output voltage range (VOUT) . -0.5 V dc to VCC+ 0.5 V dc Clamp diode current 20 mA DC output current (per p

9、in) 25 mA DC VCCor GND current (per pin) . 50 mA Storage temperature range (TSTG) . -65C to +150C Maximum power dissipation (PD) . 500 mW 4/ Lead temperature (soldering 10 seconds) . 300C Thermal resistance, junction-to-case (JC): Cases E and 2 See MIL-STD-1835 Junction temperature (TJ) 175C 1.4 Rec

10、ommended operating conditions. Supply voltage range (VCC) +2.0 V dc to +6.0 V dc Case operating temperature range (TC) . -55C to +125C Input rise or fall time (tr, tf): VCC= 2.0 V . 0 to 1000 ns VCC= 4.5 V . 0 to 500 ns VCC= 6.0 V . 0 to 400 ns 1/ Stresses above the absolute maximum rating may cause

11、 permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise specified, all voltages are referenced to ground. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temp

12、erature range of -55C to +125C. 4/ For TC= +100C to +125C, derate linearly at 12 mW/C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86884 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SH

13、EET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in t

14、he solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPA

15、RTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4

16、D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents cited in the solicitation or contract. JEDEC SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) J

17、EDEC Standard No. 7 - Standard for Description of 54/74HCXXXXX and 54/74HCTXXXXX Advanced High-Speed CMOS Devices. (Copies of these documents are available online at http:/www.jedec.org or from JEDEC Solid State Technology Association, 3103 North 10thStreet, Suite 240-S Arlington, VA 22201). 2.3 Ord

18、er of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 I

19、tem requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manuf

20、acturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may m

21、ake modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow opti

22、on is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal co

23、nnections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86884 DLA LAND AND MARITIME COLUMBUS, OHIO 43

24、218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 4. 3.3 Electrical performance characteristics. Unless

25、 otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests fo

26、r each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feas

27、ible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be repl

28、aced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 h

29、erein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of

30、conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DL

31、A Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproducti

32、on or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86884 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Test conditions 1/ -55C TC+125C unless o

33、therwise specified Group A subgroups Device type Limits Unit Min Max High level output voltage VOHVIN= VIHor VILIOH= -20 A VCC= 2.0 V 1, 2, 3 All 1.9 V VCC= 4.5 V 4.4 VCC= 6.0 V 5.9 VIN= VIHor VILIOH= -4.0 mA VCC= 4.5 V 3.7 VIN= VIHor VILIOH= -5.2 mA VCC= 6.0 V 5.2 Low level output voltage VOLVIN= V

34、IHor VILIOL= +20 A VCC= 2.0 V 1, 2, 3 All 0.1 V VCC= 4.5 V 0.1 VCC= 6.0 V 0.1 VIN= VIHor VILIOL= +4.0 mA VCC= 4.5 V 0.4 VIN= VIHor VILIOL= +5.2 mA VCC= 6.0 V 0.4 High level input voltage 2/ VIHVCC= 2.0 V 1, 2, 3 All 1.5 V VCC= 4.5 V 3.15 VCC= 6.0 V 4.2 Low level input voltage 2/ VILVCC= 2.0 V 1, 2,

35、3 All 0.3 V VCC= 4.5 V 0.9 VCC= 6.0 V 1.2 Quiescent supply current ICCVCC= 6.0 V, VIN= VCCor GND 1, 2, 3 All 160 A Input leakage current IINVCC= 6.0 V, VIN= VCCor GND 1, 2, 3 All 1.0 A Input capacitance CINVIN= 0.0 V, TC= 25C, See 4.3.1c 4 All 10.0 pF Functional tests See 4.3.1d 7 All L H Propagatio

36、n delay time, select input A, B, C to output Y 3/ tPHL1, tPLH1CL= 50 pF 10% See figure 4 VCC= 2.0 V 9 All 180 ns 10, 11 270 VCC= 4.5 V 9 36 10, 11 54 VCC= 6.0 V 9 31 10, 11 46 Propagation delay time, enable input G1, G2A, G2B to output Y 3/ tPHL2, tPLH2CL= 50 pF 10% See figure 4 VCC= 2.0 V 9 All 175

37、 ns 10, 11 265 VCC= 4.5 V 9 35 10, 11 53 VCC= 6.0 V 9 30 10, 11 45 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86884 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION

38、 LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Test conditions 1/ -55C TC+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Transition time 4/ tTHL, tTLHCL= 50 pF 10% See figure 4 VCC= 2.0 V 9 All 75 ns 10

39、, 11 110 VCC= 4.5 V 9 15 10, 11 22 VCC= 6.0 V 9 13 10, 11 19 1/ For a power supply of 5.0 V 10%, the worst case output voltages (VOHand VOL) occur for HC at 4.5 V. Thus, the 4.5 V values should be used when designing with this supply. Worst case VIHand VILoccur at VCC= 5.5 V and 4.5 V, respectively.

40、 (The VIHvalue at 5.5 V is 3.85 V). The worst case leakage currents (IINand ICC) occur for CMOS at the higher voltage and so the 6.0 V values should be used. Power dissipation capacitance (CPD), typically 85 pF, determines the no load dynamic power consumption, PD= CPDVCC2f + ICCVCC, and the no load

41、 dynamic current consumption, IS= CPDVCCf + ICC. 2/ Tests not required if applied as a forcing function for VOHand VOL. 3/ AC testing at VCC= 2.0 V and VCC= 6.0 V shall be guaranteed, if not tested, to the specified limits. 4/ Transition times, if not tested, shall be guaranteed to the specified lim

42、its. Device type 01 Case outlines E 2 Terminal number Terminal symbol Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 A B C G2A G2B G1 Y7 GND Y6 Y5 Y4 Y3 Y2 Y1 Y0 VCC- - - - NC A B C G2A NC G2B G1 Y7 GND NC Y6 Y5 Y4 Y3 NC Y2 Y1 Y0 VCCNC = No internal connection FIGURE 1. Terminal

43、connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86884 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Enable inputs Select inputs Outputs G1 G2A G2B

44、 C B A Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 X H X X X X L L L L L L L L X X H X X X L L L L L L L L L X X X X X L L L L L L L L H L L L L L H L L L L L L L H L L L L H L H L L L L L L H L L L H L L L H L L L L L H L L L H H L L L H L L L L H L L H L L L L L L H L L L H L L H L H L L L L L H L L H L L H H L L L L

45、 L L L H L H L L H H H L L L L L L L H FIGURE 2. Truth table. FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86884 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SH

46、EET 8 DSCC FORM 2234 APR 97 NOTES: 1. CLincludes test jig and probe capacitance. 2. Input signal from pulse generator: PRR 1 MHz; ZO= 50; tr= 6.0 ns; tf= 6.0 ns; trand tfshall be measured from 0.1 VCCto 0.9 VCCand from 0.9 VCCto 0.1 VCC, respectively; duty cycle = 50 percent. 3. Timing parameters sh

47、all be tested at a minimum input frequency of 1 MHz. 4. The outputs are measured one at a time with one transition per measurement. FIGURE 4. Switching waveforms and test circuit. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT

48、DRAWING SIZE A 5962-86884 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: