DLA SMD-5962-88742 REV B-2011 MICROCIRCUIT DIGITAL BIPOLAR ADVANCED LOW POWER SCHOTTKY TTL HEX NONINVERTING BUFFERS MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update to reflect latest changes in format and requirements. Editorial changes throughout. -les 04-07-28 Raymond Monnin B Update drawing as part of 5 year review. jt 11-11-08 C. SAFFLE THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. RE

2、V SHEET REV SHEET REV STATUS REV B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Larry T. Gauder DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES

3、OF THE DEPARTMENT OF DEFENSE CHECKED BY Ray Monnin APPROVED BY Michael A. Frye MICROCIRCUIT, DIGITAL, BIPOLAR, ADVANCED LOW POWER SCHOTTKY, TTL, HEX NONINVERTING BUFFERS, MONOLITHIC SILICON DRAWING APPROVAL DATE 88-10-12 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-88742 SHEET 1 OF 9 DSCC F

4、ORM 2233 APR 97 5962-E037-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88742 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawi

5、ng describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-88742 01 C A Drawing number Device type (see 1.2.1) Case out

6、line (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type. The device type identify the circuit function as follows: Device type Generic number Circuit function 01 54ALS1035 Hex noninverting buffers with open collector outputs 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835

7、 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 dual-in-line D GDFP1-F14 or CDFP2-F14 14 flat 2 CQCC1-N20 20 square chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. S

8、upply voltage range -0.5 V minimum dc to +7.0 V dc maximum Input voltage range . -1.5 V dc at 18 mA to +7.0 V dc Storage temperature range -65C to +150C Maximum power dissipation (PD) . 77 mW 1/ Lead temperature (soldering, 10 seconds) . +300C Junction temperature (TJ) +175C Thermal resistance, junc

9、tion-to-case (JC) . See MIL-STD-1835 1.4 Recommended operating conditions. Supply voltage range (VCC) +4.5 V dc minimum to +5.5 V dc maximum Minimum high level input voltage (VIH) . 2.0 V dc Maximum low level input voltage (VIL): TC= +125C . 0.7 V dc TC= -55C . 0.8 V dc TC= +25C . 0.7 V dc Maximum h

10、igh level output voltage (VOH) . 5.5 V dc Maximum low level output current (IOL) 12 mA Case operating temperature range (TC) . -55C to +125C _ 1/ Maximum power dissipation is defined as VCCX ICC, and must withstand the added PDdue to short circuit test e.g., IOS. Provided by IHSNot for ResaleNo repr

11、oduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88742 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following s

12、pecification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, Genera

13、l Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Dra

14、wings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and t

15、he references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-

16、PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be pro

17、cessed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect

18、form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construc

19、tion, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table sha

20、ll be as specified on figure 2. 3.2.4 Test circuit and switching waveforms. The test circuit and switching waveforms shall be as specified on figure 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88742 DL

21、A LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full case operating temperature

22、range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN l

23、isted in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance in

24、dicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A c

25、ertificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufactu

26、rers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change.

27、Notification of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required

28、documentation. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88742 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVIS

29、ION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC +125C 1/ unless otherwise specified Group A subgroups Device type Limits Unit Min Max Low level output voltage VOLVCC= 4.5 V, VIH= 2.0 V, IOL= 12 mA 2/ VILat: +125C = 0.7 V -55C

30、= 0.8 V +25C = 0.7 V 1, 2, 3 All 0.4 V High level output current IOH VCC= 4.5 V, VOH= 5.5 V 1, 2, 3 All 0.1 mA Input clamp voltage VIC VCC= 4.5 V, IIN= -18 mA 1, 2, 3 All -1.5 V Low level input current IILVCC= 5.5 V, VIN= 0.4 V Unused inputs 4.5 V 1, 2, 3 All -0.1 mA High level input current IIH1VCC

31、= 5.5 V, VIN= 2.7 V Unused inputs = 0.0 V 1, 2, 3 All 20 A IIH2VCC= 5.5 V, VIN= 7.0 V Unused inputs = 0.0 V 1, 2, 3 All 0.1 mA Supply current ICCHVCC= 5.5 V, VIN= 4.5 V 1, 2, 3 All 6 mA ICCLVCC= 5.5 V, VIN= 0.0 V 1, 2, 3 All 14 mA Functional tests See 4.3.1c 3/ 7, 8 All Propagation delay time, from

32、A to Y tPLHVCC= 4.5 to 5.5 V, CL= 50 pF, 9, 10, 11 All 5 35 ns tPHLRL= 680, See figure 3 4/ 9, 10, 11 All 2 14 ns 1/ Unused inputs that do not directly control the pin under test must be 2.5 V or 0.4 V. No unused inputs shall exceed 5.5 V or go less than 0.0 V. No inputs shall be floated. 2 All outp

33、uts must be tested. In the case where only one input at VILmaximum or VIHminimum produces the proper output state, the test must be performed with each input being selected as the VILmaximum or VIHminimum input. 3/ Functional tests shall be conducted at input test conditions of GND VIL VOLand VOH VI

34、H VCC. 4/ Propagation delay limits are based on single output switching. Unused inputs = 3.5 V or 0.3 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88742 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 R

35、EVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 Case outlines C and D 2 Terminal number Terminal symbol 1 1A NC 2 1Y 1A 3 2A 1Y 4 2Y 2A 5 3A NC 6 3Y 2Y 7 GND NC 8 4Y 3A 9 4A 3Y 10 5Y GND 11 5A NC 12 6Y 4Y 13 6A 4A 14 VCC5Y 15 - - - NC 16 - - - 5A 17 - - - NC 18 - - - 6Y 19 - - - 6A 20 - - - VCCNC = No

36、 connection FIGURE 1. Terminal connections. Input A Output Y H H L L H = High level voltage L = Low level voltage FIGURE 2. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88742 DLA LAND AND MARI

37、TIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 NOTES: 1. CLincludes probe and jig capacitance. 2. All input pulses have the following characteristics: PRR 10 MHz, duty cycle = 50%, tr= tf= 3 ns 1 ns. 3. The outputs are measured one at a time with one input transition p

38、er measurement. FIGURE 3. Test circuit and switching waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88742 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 AP

39、R 97 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection.

40、The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The t

41、est circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electri

42、cal parameter tests prior to burn-in are optional at the discretion of the manufacturer. TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) - Final electrical test paramete

43、rs (method 5004) 1*, 2, 3, 7, 8, 9, 10, 11 Group A test requirements (method 5005) 1, 2, 3, 7, 8, 9, 10, 11 Groups C and D end-point electrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroup 1 and 7. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordanc

44、e with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 4, 5, and 6 in table I, method 5005 of MIL-STD-883 shall be omitted. c. Subgroups 7

45、and 8 shall include verification of the truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88742 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 4.3.2

46、Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A or D. The test circuit shall be maintained by the manufacturer under document revision level control and sha

47、ll be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, e

48、xcept as permitted by method 1005 of MIL-STD-883. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device cov