1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing to current requirements. Editorial changes throughout. - drw 02-08-16 Raymond Monnin THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV SHET REV STATUS REV A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9
2、10 PMIC N/A PREPARED BY Gary Zahn DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Ray Monnin COLUMBUS, OHIO 43216 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, LINEAR, CMOS, QUAD ANALOG SWITCH, MONOLITHIC
3、 SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 89-05-08 AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-88750 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E531-02 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for Resal
4、eNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88750 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883
5、 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-88750 01 E A Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 D
6、evice type. The device type identify the circuit function as follows: Device type Generic number Circuit function 01 IH5352 Quad, CMOS SPST, RF/video analog switch 1.2.2 Case outline. The case outline are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals P
7、ackage style E GDIP1-T16 OR CDIP2-T16 16 Dual-in-line 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. V+ to ground . +18 V dc V- to ground -18 V dc VLto ground V+ to V- Logic control voltage. V+ to V- Analog input voltage V+ to V- Curren
8、t (any terminal) . 50 mA Storage temperature range. -65C to +150C Lead temperature (soldering, 10 seconds). +300C Power dissipation (PD) 450 mW 1/ Thermal resistance, junction-to-case (JC). See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA) 120C/W Junction temperature (TJ). +150C 1.4 Reco
9、mmended operating conditions. Positive supply voltage range (V+) +5.0 V dc to +15 V dc Logic supply voltage range (VL) +5.0 V dc to +15 V dc Negative supply voltage range (V-). -5.0 V dc to -15 V dc Ambient operating temperature range (TA) -55C to +125C 1/ Derate above TA= +25C at 4.0 mW/C. Provided
10、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88750 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, stan
11、dards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS)
12、and supplement thereto, cited in the solicitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Compone
13、nt Case Outlines. HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization Document Order Desk, 700 R
14、obbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unl
15、ess a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufactu
16、rer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This
17、 QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance
18、with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline. The case outline shall be in accordance
19、 with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics
20、are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for Resa
21、leNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88750 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -5
22、5C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min MaxSwitch “ON” resistance RDS(ON)IS= 10 mA, VD= 5.0 V 1, 3 All 75 VIN 2.4 V 2 100 2/ VD= 10 V 1, 3 125 2 175 IS= 10 mA, V+ = VL= +5.0 V, 1, 3 250 V- = -5.0 V, VD= 3.0 V, VIN= 3.0 V 2 350 Logic high input voltage VIH
23、1, 2, 3 All 2.4 V Logic low input voltage VIL1, 2, 3 All 0.8 V Switch “OFF” leakage ID(OFF)VS/D= 5.0 V, VS/D= 14V, 1 All 1.0 nA current VIN 0.8 V 3/ 2, 3 50 IS(OFF)1 1.0 2, 3 50 Switch “ON” leakage ID(ON)+ VS/D= 5.0 V, VS/D= 14V, 1 All 1.0 nA current IS(ON)VIN 2.4 V 3/ 2, 3 100 Logic low input curre
24、nt IILVIN= 0.8 V 1, 3 All 1.0 A 2 10 Logic high input current IIHVIN= 2.4 V 1, 3 1.0 A 2 10 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88750 DEFENSE SUPPLY CENTER COLUMBUS
25、COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min MaxQuiescent supply current I+ VIN= 0.0 V or 5.0 V 1,
26、 3 All 1.0 A 2 10 I- 1, 3 1.0 2 10 IL1, 3 1.0 2 10 Functional test FT See 4.3.1c 7, 8 All Switch “ON” time tONSee figure 3 9, 10, 11 All 400 ns Switch “OFF” time tOFFSee figure 3 9, 10, 11 All 200 ns 1/ V+ = +15 V, VL= +5.0 V, and V- = -15 V unless otherwise specified. 2/ The logic inputs are either
27、 2.4 V or 0.8 V, as required, for this test. 3/ Positive and negative voltages applied to opposite sides of switch, in both directions successively. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88750 DEFEN
28、SE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 Device type 01 Case outline E Terminal number Terminal symbol 1 Logic input 1 2 Analog input 1 3 Logic input 2 4 Analog input 2 5 Logic input 3 6 Analog input 3 7 Logic input 4 8 Analog input 4 9 VL10
29、Output 4 11 V- 12 Output 3 13 Ground 14 Output 2 15 V+ 16 Output 1 FIGURE 1. Terminal connections. Logic Switch 0 ON 1 OFF Logic “0” = 0.8 V Logic “1” = 2.4 V FIGURE 2. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUI
30、T DRAWING SIZE A 5962-88750 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 FIGURE 3. Switching time test circuit and waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIR
31、CUIT DRAWING SIZE A 5962-88750 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer
32、s PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator
33、 “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certific
34、ate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the re
35、quirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to
36、 DSCC-VA shall be required in accordance with MIL-PRF-38535, appendix A. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at
37、the option of the reviewer. 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices pr
38、ior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the prepa
39、ring or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as s
40、pecified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88750 DEFENSE SUPPLY
41、 CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 9 DSCC FORM 2234 APR 97 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall app
42、ly. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 4, 5, and 6 in table I, method 5005 of MIL-STD-883 shall be omitted. c. Subgroups 7 and 8 shall include verification of the truth table. TABLE II. Electrical test requirements. MIL-STD-883 test requirements
43、 Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) 1 Final electrical test parameters (method 5004) 1*, 2, 3, 7, 9 Group A test requirements (method 5005) 1, 2, 3, 7, 8, 9, 10, 11 Groups C and D end-point electrical parameters (method 5005)
44、1 * PDA applies to subgroup 1. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer u
45、nder document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL-STD-883. (2) TA=
46、+125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88750 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-500
47、0 REVISION LEVEL A SHEET 10 DSCC FORM 2234 APR 97 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applic
48、ations (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMDs. All proposed changes to existing SMDs will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus when a system a
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1