DLA SMD-5962-89507 REV C-2009 MICROCIRCUIT LINEAR HIGH SPEED CMOS QUAD BILATERAL SWITCH MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add vendor CAGE 01295 for case outlines C and Z. Add case outline 2. Delete vendor CAGE 18714. Editorial changes throughout 91-02-26 M. A. Frye B Update boilerplate. Change VCCrange in 1.3. Add source of supply jak. 00-07-18 Monica L. Poelking C

2、Add vendor cage Code 3V146. Update the boilerplate paragraphs to current MIL-PRF-38535 requirements. MAA. 09-02-10 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Marcia B. Kelleher STANDARD MICROC

3、IRCUIT DRAWING CHECKED BY Thomas J. Ricciuti DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, LINEAR, HIGH SPEED CMOS, QUAD BILATERAL SWITCH, MONOLITHIC SILICON AND AGENCIES

4、OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 89-11-02 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-89507 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E135-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZ

5、E A 5962-89507 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 PIN.

6、The PIN is as shown in the following examples. 5962-89507 01 C A Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54HC4066 Quad bilate

7、ral switch 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line package 2 CQCC1-N20 20 Square leadless chip carrier 1.2.3 Lead finish. The lead finish is as

8、specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +10.5 V dc DC input voltage range (VIN) -0.5 V dc to VCC+0.5 V dc DC output voltage range (VOUT). -0.5 V dc to VCC+0.5 V dc Input clamp current (IIK) (VINVCC) 20 mA Output clamp cur

9、rent (IOK) (VOUTVCC). 20 mA Continuous output current (IOUT) (VOUT= 0.0 or VCC). 25 mA Continuous current through VCCor GND . 50 mA Storage temperature range (TSTG) . -65C to +150C Maximum power dissipation (PD): 500 mW 4/ Lead temperature (soldering, 10 seconds) +260C Thermal resistance, junction-t

10、o-case (JC). See MIL-STD-1835 Junction temperature (TJ) +175C 5/ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability 2/ Unless otherwise noted, all voltages are referenced to G

11、ND. 3/ The limits for the parameters specified herein shall apply over the full specified VCC range and case temperature range of -55C to +125C. 4/ For TC= +100C to +125C, derate linearly at 12 mW/C. 5/ Maximum junction temperature shall not be exceeded except for allowable short duration burn-in sc

12、reening conditions in accordance with method 5004 of MIL-STD-883. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89507 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC F

13、ORM 2234 APR 97 1.4 Recommended operating conditions. 1/ 2/ Supply voltage range (VCC) +2.0 V dc to +10.0 V dc DC input voltage range (VIN) 0.0 V dc to VCCAnalog switch voltage range (VIN) 0.0 V dc to VCCCase operating temperature range (TC) . -55C to +125C Input rise or fall time (tr, tf): VCC= 2.0

14、 V 0 to 1000 ns VCC= 4.5 V 0 to 500 ns VCC= 6.0 V 0 to 400 ns Control input rise or fall time (VCC= 10.0 V) . 0 to 250 ns 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent sp

15、ecified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Stan

16、dard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil

17、/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in th

18、is document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Unless otherwise noted, all voltages are referenced to GND. 2/ The limits for the parameters specified herein shall apply over the full specified VCC range and case temperature range of

19、 -55C to +125C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89507 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requireme

20、nts. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who h

21、as been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modificat

22、ions to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3

23、.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance w

24、ith 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Switching waveforms and test circuits. The s

25、witching waveforms and test circuits shall be as specified in figure 4. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical

26、 test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein.

27、In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.6 Certificate of compliance. A certificate of compliance shall be requi

28、red from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, app

29、endix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required in ac

30、cordance with MIL-PRF-38535, appendix A. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. Prov

31、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89507 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limit

32、s Test Symbol Test conditions -55C TC +125C unless otherwise specified Group A subgroups Min Max Unit VCC= 2.0 V 1/1.5 VCC= 4.5 V 3.15 High level input voltage VIH VCC= 9.0 V 1/1, 2, 3 6.3 V VCC= 2.0 V 1/0.5 VCC= 4.5 V 1.35 Low level input voltage VIL VCC= 9.0 V 1/1, 2, 3 2.7 V 1 95 VCC= 4.5 V 2, 3

33、142 1 84 VCC= 6.0 V 1/2, 3 126 1 70 VIN= VCC VIS= VCCto GND IO= 1.0 mA VCC= 9.0 V 2, 3 105 1 80 VCC= 4.5 V 1/2, 3 128 1 75 VCC= 6.0 V 1/2, 3 113 1 60 On resistance RONVIN= VCC VIS= VCCor GND IO= 1.0 mA VCC= 9.0 V 1/2, 3 95 1 0.1 Switch off leakage current IOZ VIN= VIL,VIS= VCCor GND VCC= 10.0 V 2, 3

34、 1.0 A 1 0.1 Input leakage current IIL, IIHVIN= VCCor GND VCC= 10.0 V 2, 3 1.0 A See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89507 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, O

35、HIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Test conditions -55C TC +125C unless otherwise specified Group A subgroups Min Max Unit 1 2 VCC= 6.0 V 1/ 2, 3 40 A 1 16 Quiescent device current ICCVIN= VCCo

36、r GND VCC= 10.0 V 1/ 2, 3 320 A Input control Capacitance CINSee 4.3.1c 4 10.0 pF Functional tests See 4.3.1d 7, 8 9 60 VCC= 2.0 V 10, 11 90 9 12 ns VCC= 4.5 V 10, 11 18 9 8 Propagation delay time, Switch In to Out tPLH tPHL 2/ CL= 50 pF See figure 4, Configuration A VCC= 9.0 V 10, 11 13 ns 9 100 VC

37、C= 2.0 V 1/ 10, 11 150 9 20 ns VCC= 4.5 V 10, 11 30 9 12 Switch turn-on, nE to nZ tPZH tPZL CL= 50 pF RL= 1k See figure 4, Configuration B VCC= 9.0 V 1/ 10, 11 18 ns 9 150 VCC= 2.0 V 1/ 10, 11 225 9 30 ns VCC= 4.5 V 10, 11 45 9 24 Switch turn-off, nE to nZ tPHZ tPLZ CL= 50 pF RL= 1k See figure 4, Co

38、nfiguration B VCC= 9.0 V 1/ 10, 11 36 ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89507 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7

39、DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Test conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Min Max Unit Switch frequency response bandwidth at -3 dB 3/ Adjust input level for 0 dBm at output, f = 1 MHz, VISis ce

40、ntered at VCC/2, VCC= 4.5 V, see figure 4, configuration C 9 200 MHz Crosstalk between any two switches 3/ Adjust input level for 0 dBm at VIS, VISis centered at VCC/2, VCC= 4.5 V, see figure 4, configuration D 1 -72 dB Switch off signal feedthrough 3/ Adjust input level for 0 dBm at VIS, VISis cent

41、ered at VCC/2, VCC= 4.5 V, see figure 4, configuration E 1 -72 dB VCC= 4.5 V, VIS= 4 VP-P, f = 1 kHz, see figure 4, configuration F 0.022 Total harmonic distortion 3/ VCC= 9.0 V, VIS= 8 VP-P, f = 1 kHz, see figure 4, configuration F 1 0.008 % Switch input capacitance CS3/ 4 5 pF 1/ This parameter is

42、 guaranteed, if not tested, to the limits specified in table I. 2/ This parameter is guaranteed through the RONtests. 3/ The analog channel characteristics are for information only and are not tested. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-S

43、TANDARD MICROCIRCUIT DRAWING SIZE A 5962-89507 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outline C 2 Terminal number Terminal symbol Terminal symbol 1 1Y NC 2 1Z 1Y3 2Z 1Z 4 2Y 2Z 5 2E NC 6 3E 2Y7 GND NC 8 3Y 2E 9 3Z 3

44、E 10 4Z GND 11 4Y NC12 4E 3Y 13 1E 3Z 14 VCC4Z 15 NC 16 4Y17 NC 18 4E 19 1E 20 VCCNC = No internal connection FIGURE 1. Terminal connections. nE Input Switch L Off H On H = High voltage level (steady state) L = Low voltage level (steady state) FIGURE 2. Truth table. Provided by IHSNot for ResaleNo r

45、eproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89507 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking

46、 permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89507 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 10 DSCC FORM 2234 APR 97 FIGURE 4. Switching waveforms and test circuits. Provided by IHSNot for ResaleNo reproduction or networking

47、 permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89507 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 11 DSCC FORM 2234 APR 97 FIGURE 4. Switching waveforms and test circuits Continued. Provided by IHSNot for ResaleNo reproduction or

48、networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89507 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 12 DSCC FORM 2234 APR 97 FIGURE 4. Switching waveforms and test circuits Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89507 DEFENSE SUPPLY CENTER COLUMBUS CO