DLA SMD-5962-89510 REV B-2012 MICROCIRCUIT DIGITAL ADVANCED SCHOTTKY TTL TRIPLE 3-INPUT NOR NOR GATES MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update to reflect latest changes in format and requirements. Editorial changes throughout. -les 04-08-05 Raymond Monnin B Update drawing as part of 5 year review 12-01-18 C. SAFFLE THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV SH

2、EET REV SHEET REV STATUS REV B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Monica L. Poelking DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES O

3、F THE DEPARTMENT OF DEFENSE CHECKED BY Ray Monnin APPROVED BY Michael A. Frye MICROCIRCUIT, DIGITAL, ADVANCED SCHOTTKY, TTL, TRIPLE, 3-INPUT, NOR GATES, MONOLITHIC SILICON DRAWING APPROVAL DATE 88-12-15 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-89510 SHEET 1 OF 9 DSCC FORM 2233 APR 97 59

4、62-E130-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89510 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes devic

5、e requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89510 01 C A Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) L

6、ead finish (see 1.2.3) 1.2.1 Device type. The device type identify the circuit function as follows: Device type Generic number Circuit function 01 54F27 Triple 3-input, positive NOR gates 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descript

7、ive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 dual-in-line D GDFP1-F14 or CDFP2-F14 14 flat 2 CQCC1-N20 20 square chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage range -0.5 V dc to +7.0 V

8、dc Input voltage range . -1.2 V dc at 18 mA to +7.0 V dc Input current range -30 mA to 5.0 mA Voltage applied to any output in the high state . -0.5 V dc to VCCCurrent into any output in the low state . 40 mA Maximum power dissipation (PD) . 66 mW 1/ Storage temperature range -65C to +150C Lead temp

9、erature (soldering, 10 seconds) . +300C Junction temperature (TJ) +175C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 1.4 Recommended operating conditions. Supply voltage range (VCC) +4.5 V minimum dc to +5.5 V maximum dc Minimum high level input voltage (VIH) . +2.0 V dc Maximum low

10、level input voltage (VIL) +0.8 V dc Maximum input clamp current (IIC) . -18 mA Maximum high level output Current (IOH) -1.0 mA Maximum low level output current (IOL) +20 mA Case operating temperature range (TC) . -55C to +125C _ 1/ Maximum power dissipation is defined as VCCX ICC, and must withstand

11、 the added PDdue to short circuit test e.g., IOS. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89510 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 2. APPLIC

12、ABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTME

13、NT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-

14、103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2

15、Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.

16、1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a ma

17、nufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan ma

18、y make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow o

19、ption is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal

20、 connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Test circuit and switching waveforms. The test circuit and switching waveforms shall be as specified on figure 3. Provided by IHSNot for ResaleNo reproduction or networking per

21、mitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89510 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics

22、 are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be

23、 in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not m

24、arking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-

25、38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritim

26、e -VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided

27、with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime s agent, and the acquiring a

28、ctivity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICRO

29、CIRCUIT DRAWING SIZE A 5962-89510 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max High lev

30、el output voltage VOHVCC= 4.5 V, VIL= 0.8 V, VIH= 2.0 V, IOH= -1.0 mA 1, 2, 3 All 2.5 V Low level output voltage VOLVCC= 4.5 V, VIL= 0.8 V, VIH= 2.0 V, IOL= 20 mA 1, 2, 3 All 0.5 V Input clamp voltage VICVCC= 4.5 V, IIN= -18 mA 1, 2, 3 All -1.2 V Low level input current IILVCC= 5.5 V, VIN= 5.5 V 1,

31、2, 3 All -0.6 mA High level input current IIH1VCC= 5.5 V, VIN= 2.7 V 1, 2, 3 All 20 A IIH2VCC= 5.5 V, VIN= 7.0 V 1, 2, 3 All 0.1 mA Short circuit output current IOSVCC= 5.5 V, VOUT= 0.0 V 1/ 1, 2, 3 All -60 -150 mA Supply current (total) ICCHVCC= 5.5 V, VIN= 0.0 V 1, 2, 3 All 5.5 mA ICCLVCC= 5.5 V,

32、VIN= 4.5 V, unused inputs = 0.0 V 1, 2, 3 All 12 mA Functional tests See 4.3.1c, VCC= 4.5 V, 5.5 V 2/ 7, 8 All Propagation delay time, tPLHCL= 50 pF VCC= 5.0 V 9 All 1.2 5.0 ns from A, B to Y RL= 500 VCC = 4.5 V to 5.5 V 10, 11 All 1.0 6.0 tPHLsee figure 3 VCC= 5.0 V 9 All 1.0 4.5 ns VCC= 4.5 V to 5

33、.5 V 10, 11 All 1.0 5.5 1/ Not more than one output will be shorted at one time and the duration of the short circuit condition shall not exceed one second. 2/ Functional tests shall be conducted at input test conditions of GND VIL VOLand VOH VIH VCC. Provided by IHSNot for ResaleNo reproduction or

34、networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89510 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 Device type 01 Case outlines C and D 2 Terminal number Terminal symbol 1 1A NC 2 1B 1A 3 2A 1B 4 2B 2A 5 2C

35、 NC 6 2Y 2B 7 GND NC 8 3Y 2C 9 3A 2Y 10 3B GND 11 3C NC 12 1Y 3Y 13 1C 3A 14 VCC3B 15 - - - NC 16 - - - 3C 17 - - - NC 18 - - - 1Y 19 - - - 1C 20 - - - VCCNC = No connection FIGURE 1. Terminal connections. Inputs Output A B C Y H X X L X H X L X X H L L L L H H = High level voltage L = Low level vol

36、tage X = Irrelevant FIGURE 2. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89510 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 NOTES: 1. CLincl

37、udes probe and jig capacitance. 2. All input pulses have the following characteristics: PRR = 1 MHz, tr= tf= 2.5 ns, duty cycle = 50%. 3. The outputs are measured one at a time with one transition per measurement. FIGURE 3. Test circuit and switching waveforms. Provided by IHSNot for ResaleNo reprod

38、uction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89510 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accor

39、dance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test c

40、ondition A or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accord

41、ance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. TABLE II. Ele

42、ctrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) - - - Final electrical test parameters (method 5004) 1*, 2, 3, 7, 8, 9, 10, 11 Group A test requirements (method 5005) 1, 2, 3, 7, 8,

43、9, 10, 11 Groups C and D end-point electrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroup 1. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C and D inspections. The following additional c

44、riteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 4, 5 and 6 in table I, method 5005 of MIL-STD-883 shall be omitted. c. Subgroups 7 and 8 shall include verification of the truth table. Provided by IHSNot for ResaleNo reproduction or netwo

45、rking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89510 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b

46、. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify t

47、he inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 5. PACKAGING 5.1 Packaging requirements. The requirement

48、s for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMDs. All proposed changes to existing SMDs will be coordinated with the user