DLA SMD-5962-89563 REV C-2011 MICROCIRCUIT HYBRID LINEAR 16-BIT A D CONVERTER.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Made technical changes to table I. Editorial changes throughout. 91-08-06 W. Heckman B Updated drawing to the latest requirements. -sld 05-06-03 Raymond Monnin C Updated drawing paragraphs. -sld 11-11-08 Charles F. Saffle THE ORIGINAL FIRST SHEET

2、 OF THIS DOCUMENT HAS BEEN REPLACED REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Steve Duncan DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Robert M.

3、 Heber THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY William K. Heckman MICROCIRCUIT, HYBRID, LINEAR, 16-BIT, A/D CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 90-06-29 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-89563 SHEET 1 OF 11 DSCC FORM

4、2233 APR 97 5962-E054-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89563 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing d

5、ocuments five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN

6、. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 89563 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assu

7、rance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number C

8、ircuit function Short cycle 1/ 01 MN5290 A/D converter, 16-bit resolution 14-bit 02 MN5291 A/D converter, 16-bit resolution 13-bit 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements

9、of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applic

10、ations. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible li

11、mited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C and D). 1/ For applications requiring fewer than 16 bits of resolution, the device types 01 and 02 can be truncated or short cycled at

12、 the desired number of bits with a proportionate decrease in conversion time. To truncate at n bits, simply connect the n + 1 bit output to the Short Cycle pin (terminal number 32). For example, to truncate at 14 bits, connect terminal number 5 (bit 15) to terminal number 32; converting will stop an

13、d Status (terminal number 1) will go low after bit 14 has been set. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89563 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 223

14、4 APR 97 E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the except

15、ion(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-18

16、35 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 32 Hybrid package 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 2/ Positive supply voltage range (VCC) . -0.5 V dc to +18 V dc Negative supply vo

17、ltage range (VEE) +0.5 V dc to -18 V dc Logic supply voltage range (VDD) . 0 V dc to +7 V dc Analog input channels 22 V dc Digital input 0 V dc to +5.5 V dc Power dissipation (PD) . 1.08 W Thermal resistance, junction-to-case (JC) . 5C/W Thermal resistance, junction-to-ambient (JA) 28C/WLead tempera

18、ture (soldering, 10 seconds) +300C Storage temperature range -65C to +150C Junction temperature (TJ) +175C 1.4 Recommended operating conditions. Postive supply voltage range (VCC) . +14.55 V dc to +15.45 V dc Negative supply voltage range (VEE) . -14.55 V dc to -15.45 V dc Logic supply voltage range

19、 (VDD) +4.75 V dc to +5.25 V dc Ambient operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise sp

20、ecified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Sta

21、ndard Electronic Component Case Outlines. _ 2/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without l

22、icense from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89563 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Co

23、pies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the referen

24、ces cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H,

25、 and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or opti

26、mize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, co

27、nstruction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as

28、 specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test req

29、uirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer

30、s vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for

31、each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land an

32、d Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets th

33、e performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedure

34、s shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license f

35、rom IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89563 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type

36、Limits Unit Min Max ANALOG Input voltage range VIUnipolar 1,2,3 All 0 0 0 +5 +10 +20 V Bipolar -2.5 -5 -10 +2.5 +5 +10 DIGITAL Input voltage high VIHFor all digital inputs 1,2,3 All +2.0 V Input voltage low VIL+0.8 Input current high IIHFor all digital inputs, VIH= +2.4 V 1,2,3 All +40 A Input curre

37、nt low IILFor all digital inputs, VIH= +0.4 V 1,2,3 All -1.6 mA Output voltage high VOHIOH= -320 A 1,2,3 All +2.4 V Output voltage low VOL IOL= +3.2 mA +0.4 POWER SUPPLY Supply current ICCVCC= +15 V 1,2,3 All +37 mA IEEVEE= -15 V -29 IDDVDD= +5 V +18 Power consumption PD1,2,3 All 1080 mW Power suppl

38、y rejection ratio PSRR +14.5 V VCC +15.5 V 1,2,3 All -0.02 +0.02 Vs%FS%-15.5 V VEE -14.5 V -0.02 +0.02 +4.75 V VDD +5.25 V -0.01 +0.01 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A

39、 5962-89563 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max ACCURACY 2/ Unip

40、olar 10 V V+FSMSB LSB Nominal 1111 1111 1111 1* (+9.9991) 4 All +9.9841 +10.0141 V 5,6 +9.9691 +10.0291 Bipolar 10 V V+FSMSB LSB Nominal 1111 1111 1111 1* (+4.9991) 4 All +4.9791 +5.0191 5,6 +4.9591 +5.0391 Bipolar 20 V V+FSMSB LSB Nominal 1111 1111 1111 1* (+9.9982) 4 All +9.9582 +10.0382 5,6 +9.91

41、82 +10.0782 Unipolar 10 V offset VUOMSB LSB Nominal 0000 0000 0000 0* +0.0003 4 All -0.0097 +0.0103 5,6 -0.0147 +0.0153 Bipolar 10 V zero VBZ1MSB LSB Nominal * * * * -0.0003 4 All -0.0123 +0.0117 5,6 -0.0203 +0.0197 Bipolar 20 V zero VBZ2MSB LSB Nominal * * * * -0.0006 4 All -0.0246 +0.0234 5,6 -0.0

42、406 +0.0394 Bipolar zero drift VBZT 5,6 All -15 +15 ppmFSR C Unipolar offset drift UOT 5,6 All -15 +15 Gain error Ae 4 All -0.1 +0.1 % 5,6 -0.2 +0.2 Gain drift AeT 4,5,6 All -15 +15 ppm C See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

43、nse from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89563 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgr

44、oups Device type Limits Unit Min Max ACCURACY - CONTINUED Integral linearity error LE 14-bit linearity 4 All -0.5 +0.5 LSB 5,6 -1.0 +1.0 Differential linearity error DLE 14-bit linearity 4 All -0.9 +1.0 LSB 5,6 -0.9 +2.0 Minimum resolution for no missing codes 4,5,6 01 14 Bits 02 13 Reference voltag

45、e VREF4 All +9.990 +10.010 V Conversion time tc 9,10,11 All 40 s 1/ VCC= +15 V, VEE= -15 V, VDD= +5.0 V, unless otherwise specified. 2/ * The output will transition from a “1“ to “0“ or vice versa as the analog input passes through the voltages listed in the limit columns. Provided by IHSNot for Res

46、aleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89563 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Inches mm .005 0.13 .008 0.20.010 0.25.012 0.30.015 0.38.020 0.51 .025 0.64.100 2.54.

47、106 2.69.172 4.37.215 5.46 .600 15.24.800 20.321.500 38.101.712 43.48NOTES: 1. Dimensions are in inches. 2. Metric dimensions are given for general information only. 3. Unless otherwise specified, all dimensions .005 inch (0.13 mm). FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89563 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 Device types 01 and 02 Case outline X Terminal number Terminal symbol 1 STATUS (E. O.C.) 2