DLA SMD-5962-89653 REV B-2009 MICROCIRCUIT LINEAR CMOS 8-BIT VIDEO D A CONVERTER MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Make changes to 1.3, 1.4, 4.3.1c, table I, table II, figure 1, figure 3 and figure 4. 91-01-11 M. A. Frye B Redraw. Update drawing to current requirements. - drw 09-01-07 Robert M. Heber THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.

2、 REV SHET REV SHET REV STATUS REV B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Rick Officer CHECKED BY Charles E. Besore DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil APPROVED BY William J. Johnson STANDARD MICROCIRCUI

3、T DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 89-09-27 MICROCIRCUIT, LINEAR, CMOS, 8-BIT VIDEO D/A CONVERTER, MONOLITHIC SILICON AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-89653 SHEET 1 OF 13 DSCC FORM 2233 A

4、PR 97 5962-E088-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89653 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawin

5、g describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89653 01 L A Drawing number Device type (see 1.2.1) Case outl

6、ine(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type. The device type identifies the circuit function as follows: Device type Generic number Circuit function 01 BT102 8-bit video D/A converter 1.2.2 Case outline. The case outline are as designated in MIL-STD-1835 as follows: Outline letter Descrip

7、tive designator Terminals Package style L GDIP3-T24 or CDIP4-T24 24 Dual-in-line 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage (VAA) to AGND. +7.0 V dc Voltage to any digital pin AGND -0.5 V dc to VAA+0.5 V dc Storage te

8、mperature range -65C to +150C Junction temperature (TJ) 185C Lead temperature (soldering, 10 seconds) 260C Thermal resistance, junction-to-case (JC). See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA) 60C/W Analog output short circuit duration to any power supply or common (ISC) Indefinit

9、e Power dissipation (PD) . 918 mW 1.4 Recommended operating conditions. Ambient operating temperature range (TA) -55C to +125C Supply voltage range (VAA) 4.75 V dc to 5.25 V dc Reference voltage range (VREF). 1.14 V dc to 1.26 V dc Output load (RL). 37.5 ohms Provided by IHSNot for ResaleNo reproduc

10、tion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89653 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The follow

11、ing specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, G

12、eneral Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircui

13、t Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing a

14、nd the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with

15、MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be

16、 processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not aff

17、ect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, cons

18、truction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table s

19、hall be as specified on figure 2. 3.2.4 Block diagram. The logic diagram shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient oper

20、ating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,

21、-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89653 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA+125C Group A subgroupsDevice type Limits Unit unless otherwise s

22、pecified Min Max Input high voltage (TTL) VIHCLOCK 1, 2, 3 01 3.0 V Other 2.0 Input low voltage (TTL) VIL1, 2, 3 01 0.8 V Input high current (TTL) IIHVIN= 2.4 V 1, 2, 3 01 -200 -1200 A Input low current (TTL) IILVIN= 0.4 V 1, 2, 3 01 -200 -1200 A Input high voltage (CMOS) VIHCLOCK 1, 2, 3 01 4.5 V O

23、ther 3.5 Input low voltage (CMOS) VIL1, 2, 3 01 0.8 V Input high current (CMOS) IIHVIN= 3.5 V 1, 2, 3 01 2 A Input low current (CMOS) IILVIN= 1.5 V 1, 2, 3 01 2 A Voltage reference input leakage current IREFVREF= 1.235 V 1, 2, 3 01 10 A Power supply rejection ratio PSRR COMP = 0.01 F, f = 1 kHz 1, 2

24、, 3 01 0.5 %/% Analog output gray scale current range THRESHOLD SET = TTL mode 1, 2, 3 01 20.5 mA Integral linearity error IL1, 2 01 0.50 LSB 3 0.75 Differential linearity error DL1, 2, 3 01 0.50 LSB Gray scale error 1, 2, 3 01 5 % gray scale See footnotes at end of table. Provided by IHSNot for Res

25、aleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89653 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Con

26、ditions 1/ -55C TA+125C Group A subgroupsDevice type Limits Unit unless otherwise specified Min Max Overbright relative to white output current 2/ SETUP = float, RSET= 1.11 k, 1, 2, 3 01 1.60 2.40 mA White level relative to blank output current THRESHOLD SET = TTL mode 1, 2, 3 17.90 20.31 White leve

27、l relative to black output current 1, 2, 3 16.80 18.61 Black level relative to blank output current 1, 2, 3 1.10 1.70 Blank level output current 1, 2, 3 7.20 8.30 Sync level output current ISYN1, 2, 3 -10 50 A White level relative to blank output current SETUP = AGND, RSET= 1.05 k, 1, 2, 3 01 17.80

28、19.75 mA White level relative to black output current THRESHOLD SET = TTL mode 1, 2, 3 17.80 19.70 Black level relative to blank output current 1, 2, 3 -10 50 A Blank level output current 1, 2, 3 7.70 9.0 mA Sync level output current ISYN1, 2, 3 -10 50 A White level relative to blank output current

29、SETUP = VAA, RSET= 1.13 k, 1, 2, 3 01 18.0 20.60 mA White level relative to black output current THRESHOLD SET = TTL mode 1, 2, 3 16.50 18.30 Black level relative to blank output current 1, 2, 3 1.50 2.30 Blank level output current 1, 2, 3 7.10 8.30 Sync level output current ISYN1, 2, 3 -10 50 A Out

30、put compliance VOCTHRESHOLD SET = TTL mode 1, 2, 3 01 +1.4 V Input capacitance CINSee 4.3.1c 4 01 10 pF Output capacitance COUTSee 4.3.1c 4 01 30 pF Functional test See 4.3.1d 7, 8 01 See footnotes at end of table.Provided by IHSNot for ResaleNo reproduction or networking permitted without license f

31、rom IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89653 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions 1/ -55C TA+125C Group A subgroupsDevice type Limits

32、Unit unless otherwise specified Min Max Clock rate 3/ FMAX9, 10, 11 01 50 MHz Data and control setup time 3/ tSU9, 10, 11 01 5 ns Data and control hold time 3/ tH9, 10, 11 01 2 ns Clock cycle time 3/ tCYC9, 10, 11 01 20 ns Clock pulse width low 3/ tCLKL9, 10, 11 01 7 ns Clock pulse width high 3/ tCL

33、KH9, 10, 11 01 7 ns Analog output delay 3/ tDLY9 01 26 ns 10 36 11 22 Analog output rise/fall time 3/ tVRF9, 10, 11 01 6 ns Pipeline delay 4/ 9, 10, 11 01 +3 +3 Clocks VAAsupply current 3/ IAA9, 10, 11 01 175 .mA 1/ VAA= 4.75 V and 5.25 V, RSET= 1.11 k 0.1%, VREF= 1.235 V, unless otherwise specified

34、. 2/ May not be tested, but shall be guaranteed from characterization (TA= +25C, VAA= 5 V 5%) to the limits specified in table I herein. 3/ THRESHOLD SET = TTL mode, SETUP = float. Input values are 0.4 V to 3.5 V on clock and 0 to 3 volts on control and data, with input rise /fall times 3 ns, measur

35、ed between the 10 and 90 percent points. Timing reference points at 50 percent for inputs and outputs. COMP resistor = 27. Analog output load 10 pF with doubly-terminated 50 line, unless otherwise specified. See figure 4. 4/ Guaranteed by design. Provided by IHSNot for ResaleNo reproduction or netwo

36、rking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89653 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Device type 01 Case outline L Terminal number Terminal symbol 1 WHITEREF 2 BLANK 3 D74 D65 D56 D47 CLOC

37、K 8 D39 D210 D111 D012 THRESHOLD SET 13 AGND 14 VREF15 FS ADJUST16 COMP 17 VAA18 AGND 19 IOUT20 IRET21 SETUP 22 SYNC 23 10% OVERBRIGHT 24 VAAFIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING

38、 SIZE A 5962-89653 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 Description IOUT(mA) 10% OVERBRIGHT(see note) WHITEREF (see note) SYNC (see note) BLANK (see note) DAC input data WHITE + 10% 28.74 0 1 1 1 $FF WHITE 26.81 1 0 1 1 $XX WHITE 26.

39、81 1 1 1 1 $FF DATA + 10% DATA + 11.0 0 1 1 1 data DATA DATA + 9.09 1 1 1 1 data DATA SYNC DATA + 1.37 1 1 0 1 data BLACK 9.09 1 1 1 1 $00 BLACK - SYNC 1.37 1 1 0 1 $00 BLANK 7.72 X X 1 0 $XX SYNC 0 X X 0 0 $XX NOTE: Typical with white level current = 26.81 mA. RSET= 1110 ohms, VREF= 1.235 V, SETUP

40、= float. (Video output) FIGURE 2. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89653 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 FIG

41、URE 3. Block diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89653 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 10 DSCC FORM 2234 APR 97 FIGURE 4. Timing diagram. P

42、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89653 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 11 DSCC FORM 2234 APR 97 3.5 Marking. Marking shall be in accordance with M

43、IL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on

44、 the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify whe

45、n the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved s

46、ource of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivere

47、d to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required docum

48、entation. Offshore documentation shall be made available onshore at the option of the reviewer. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria sha