DLA SMD-5962-89656 REV B-2009 MICROCIRCUIT LINEAR OPERATIONAL AMPLIFIER LOW POWER MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. -ro 01-03-08 R. MONNIN B Five year review requirement. -rrp 09-05-12 J. D. RODENBECK THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV SHET REV STATUS REV B B B B B B B B B B

2、 B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY CHARLES E. BESORE DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY CHARLES E. BESORE COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY MICHAEL A. FRY

3、E MICROCIRCUIT, LINEAR, OPERATIONAL AMPLIFIER, LOW POWER, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 90-11-15 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-89656 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E007-08 Provided by IHSNot for ResaleNo reproduct

4、ion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89656 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, n

5、on-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89656 01 C X Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). T

6、he device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 HA-5141 Single, low power operational amplifier 02 HA-5142 Dual, low power operational amplifier 03 HA-5144 Quad, low power operational amplifier 1.2.2 Case outline(s). The case outline(s) are

7、as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line G MACY1-X8 8 Can P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 2 CQCC1-N20 20 Square leadless chip carrier 1.2.3 Lead finish. The lead finish is as specified i

8、n MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Voltage between +V and V terminals 35 V dc Differential input voltage 7.0 V dc Voltage at either input terminal +V to V Storage temperature range . -65C to +150C Lead temperature (soldering, 10 seconds) +275C Junction temperature (TJ) . +175

9、C Maximum power dissipation (PD) at TA= +75C: Device type 01: Case G . 0.67 W Case P . 1.21 W Case 2 1.34 W Device type 02: Case G . 0.67 W Case P . 1.22 W Case 2 1.35 W Device type 03: Case C . 1.33 W Case 2 1.32 W Provided by IHSNot for ResaleNo reproduction or networking permitted without license

10、 from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89656 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings Continued. Derating above TA= +75C Device type 01: Case G . 6.7 mW/C Case P . 12.1 mW/C Case 2 13.4 mW/C

11、Device type 02: Case G . 6.7 mW/C Case P . 12.2 mW/C Case 2 13.5 mW/C Device type 03: Case C . 13.3 mW/C Case 2 13.2 mW/C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Device type 01: Case G . 149C/W Case P . 83C/W Case 2 74C/W Device type

12、 02: Case G . 111C/W Case P . 82C/W Case 2 74C/W Device type 03: Case C . 75C/W Case 2 76C/W 1.4 Recommended operating conditions. Supply voltage range (V): Dual supply operation 1.5 V dc to 15 V dc Single supply operation . +3.0 V dc to +30 V dc Common mode input voltage (VCM) (+V - -V) / 2 Load re

13、sistance (RL) . 50 k Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified,

14、the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface

15、 Standard Electronic Component Case Outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89656 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 DEPA

16、RTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D

17、, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption h

18、as been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certifie

19、d and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in

20、 the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is requ

21、ired to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein. 3.2.2

22、Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3

23、.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in

24、 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator

25、“C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certifica

26、te of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the req

27、uirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to

28、DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the o

29、ption of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89656 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical perform

30、ance characteristics. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Input offset voltage VIO1VCM= 0 V 2/ 1 All 6.0 mV 2,3 8.0 VIO2VCM= 0 V, 3/ 1 6.0 VOUT= 1.4 V 2,3 8.0 Input bias current +IB1VCM= 0 V, 2/ 1 All 100 nA +RS= 10 k, -

31、RS= 100 2,3 125 -IB1VCM= 0 V, 2/ 1 100 +RS= 100 , -RS= 10 k 2,3 125 +IB2VCM= 0 V, VOUT= 1.4 V, 3/ 1 100 +RS= 10 k, -RS= 100 2,3 125 -IB2VCM= 0 V, VOUT= 1.4 V, 3/ 1 100 +RS= 100 , -RS= 10 k 2,3 125 Input offset current IIO1VCM= 0 V, 2/ 1 All 10 nA +RS= 10 k, -RS= 10 k 2,3 20 IIO2VCM= 0 V, VOUT= 1.4 V

32、, 2/ 1 10 +RS= 10 k, -RS= 10 k 2,3 20 Common mode range +CMR1+V = 5.0 V, -V = -25 V 1,2,3 All 10 V -CMR1+V = 25 V, -V = -5.0 V -10 +CMR2+V = 5.0 V to 2.0 V, -V = 0 V to 3.0 V, VOUT= 1.4 V to 1.6 V 0 to 3 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permit

33、ted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89656 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA+125C unless otherwise

34、specified Group A subgroups Device type Limits Unit Min Max Large signal voltage gain +AVOL1VOUT= 0 V and 10 V, 2/ 4 All 20 kV/V RL= 50 k 5,6 15 -AVOL1VOUT= 0 V and -10 V, 2/ 4 20 RL= 50 k 5,6 15 +AVOL2VOUT= 1.4 V and 2.5 V, 3/ 4 20 RL= 50 k 5,6 15 Common mode rejection ratio +CMRR1VCM= 10 V, +V = 5

35、.0 V, -V = -25 V, VOUT= -10 V 1,2,3 All 77 dB -CMRR1VCM= 10 V, +V = 25 V, -V = -5.0 V, VOUT= 10 V 77 +CMRR2VCM= 0 V to 3.0 V, +V = 2.0 V, -V = -3.0 V, VOUT= -3.0 V 77 Output voltage swing +VOUT1RL= 50 k 2/ 1,2,3 All 10 V -VOUT1RL= 50 k 2/ -10 +VOUT2RL= 50 k, 3/ 1 3.8 terminated at 2.5 V 2,3 3.5 -VOU

36、T2RL= 50 k, 3/ 1 1.0 terminated at 2.5 V 2,3 1.2 Power supply rejection ratio +PSRR1 +V = 10 V and 20 V, -V = -15 V 1,2,3 All 77 dB -PSRR1 -V = -10 V and -20 V, +V = +15 V 77 +PSRR2 +V = 5.0 V and 15 V, -V = 0 V 77 Channel separation CS RL= 50 k 1,2,3 02,03 80 dB See footnotes at end of table. Provi

37、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89656 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continu

38、ed. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Quiescent power supply current +ICC1VOUT= 0 V, 2/ 1 01 150 A IOUT= 0 mA 02 300 03 600 2,3 01 200 02 400 03 800 -ICC1VOUT= 0 V, 2/ 1 01 -150 IOUT= 0 mA 02 -300 03 -600 2,3 01 -200 0

39、2 -400 03 -800 +ICC2VOUT= 1.4 V, 3/ 1 01 80 IOUT= 0 mA 02 160 03 320 2,3 01 100 02 200 03 400 Slew rate +SR1VOUT= -3.0 V to +3.0 V, 2/ VINSR 25 V/s, AV= 1.0 V/V, TA= +25C 4 All 0.8 V/s -SR1VOUT= +3.0 V to -3.0 V, 2/ VINSR 25 V/s, AV= 1.0 V/V, TA= +25C 0.8 See footnotes at end of table. Provided by I

40、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89656 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test

41、 Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Unit Min MaxSlew rate +SR2VOUT= 0 V to +3.0 V, 3/ VINSR 25 V/s, AV= 1.0 V/V, TA= +25C 4 All 0.8 V/s -SR2VOUT= 3.0 V to 0 V, 3/ VINSR 25 V/s, AV= 1.0 V/V, TA= +25C 0.8 Full power bandwidth 4/ 5/ FPBW1VP

42、EAK= 10 V, 2/ AV= 1.0 V/V, TA= +25C 4 All 12.7 kHz FPBW2VPEAK= 1.1 V, 3/ VREF= 2.5 V, AV= 1.0 V/V, TA= +25C 115.8 Minimum closed-loop 4/ stable gain CLSG RL= 50 k, CL= 50 pF, AV= 1.0 V/V 4,5,6 All 1.0 V/V Quiescent power 6/ consumption PC1VOUT= 0 V, 2/ 1,2,3 01 6.0 mW IOUT= 0 mA, AV= 1.0 V/V 02 12 0

43、3 24 PC2VOUT= 1.4 V, 3/ 01 0.5 IOUT= 0 mA, AV= 1.0 V/V 02 1.0 03 2.0 1/ Unless otherwise specified, RS= 50 , RL= 10 k, CL= 100 pF, and VOUT= 0 V. For device types 02 and 03, tests apply to each amplifier. 2/ +V = +15 V and V = -15 V. 3/ +V = +5.0 V and V = 0.0 V 4/ If not tested, shall be guaranteed

44、 to the limits specified in table I herein. 5/ Full power bandwidth = SR / (2 x VPEAK). 6/ Quiescent power consumption based on quiescent supply current test maximum (no load outputs). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIR

45、CUIT DRAWING SIZE A 5962-89656 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 Device types 01 02 03 Case outlines G and P 2 G and P 2 C 2 Terminal number Terminal symbol 1 NC NC OUTPUT 1 NC OUTPUT 1 NC 2 -INPUT NC -INPUT 1 OUTPUT 1 -INPUT 1 OU

46、TPUT 1 3 +INPUT NC +INPUT 1 NC +INPUT 1 -INPUT 1 4 -V NC -V NC +V +INPUT 1 5 NC -INPUT +INPUT 2 -INPUT 1 +INPUT 2 NC 6 OUTPUT NC -INPUT 2 NC -INPUT 2 +V 7 +V +INPUT OUTPUT 2 +INPUT 1 OUTPUT 2 NC 8 NC NC +V NC OUTPUT 3 +INPUT 2 9 - NC - NC -INPUT 3 -INPUT 2 10 - -V - -V +INPUT 3 OUTPUT 2 11 - NC - NC

47、 -V NC 12 - NC - +INPUT 2 +INPUT 4 OUTPUT 3 13 - NC - NC -INPUT 4 -INPUT 3 14 - NC - NC OUTPUT 4 +INPUT 3 15 - OUTPUT - -INPUT 2 - NC 16 - NC - NC - -V 17 - +V - OUTPUT 2 - NC 18 - NC - NC - +INPUT 4 19 - NC - NC - -INPUT 4 20 - NC - +V - OUTPUT 4 NC = No connection FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89656 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 10 DSCC FORM 2234 APR 97 4. VERIFI