DLA SMD-5962-89802 REV B-2011 MICROCIRCUIT LINEAR PRECISION 10-VOLT VOLTAGE REFERENCE MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. - gt 04-05-06 R. MONNIN B Update boilerplate paragraphs to current MIL-PRF-38535 requirements. - ro 11-05-03 C. SAFFLE REV SHET REV SHET REV STATUS REV B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5

2、 6 7 8 9 10 PMIC N/A PREPARED BY RICK C. OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY SANDRA B. ROONEY APPROVED BY CHARLES E. BESO

3、RE MICROCIRCUIT, LINEAR, PRECISION, 10-VOLT VOLTAGE REFERENCE, MONOLITHIC SILICON DRAWING APPROVAL DATE 91-08-22 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-89802 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E236-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without l

4、icense from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89802 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordan

5、ce with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89802 01 X A Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit functio

6、n as follows: Device type Generic number Circuit function 01 LT1031B Precision 10-volt voltage reference 02 LT1031C Precision 10-volt voltage reference 03 LT1031D Precision 10-volt voltage reference 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline

7、letter Descriptive designator Terminals Package style X See figure 1 3 Can 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage (VCC) . 40 V Input-output differential voltage 35 V Output to ground voltage 1/ 16 V Output short c

8、ircuit duration: At VIN= 35 V . 10 seconds At VIN 20 V . Indefinite Trim pin to ground voltage: Positive Equal to VOUTNegative -20 V Storage temperature range -65C to +150C Power dissipation (PD) at TA= +25C 600 mW Lead temperature (soldering, 10 seconds) . 300C Junction temperature (TJ) . 150C Ther

9、mal resistance, junction-to-case (JC) 50C/W Thermal resistance, junction-to-ambient (JA) . 170C/W _ 1/ Shunt mode current limit. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89802 DLA LAND AND MARITIME COL

10、UMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.4 Recommended operating conditions. Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks f

11、orm a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFEN

12、SE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are av

13、ailable online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of

14、this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class

15、level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with

16、 the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. Th

17、ese modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be a

18、s specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specif

19、ied herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgrou

20、p are described in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89802 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance

21、 characteristics. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output voltage 2/ VRTA= 25C 1 01 9.995 10.005 V 02 9.990 10.01003 10.020Output voltage change with temperature 3/ TVR2, 3 01 5 PPM/C 02 15 03 25 Line regulation 4/ IN

22、RVV11.5 V VIN 14.5 V 1 All 4 PPM/V 2, 3 6 14.5 V VIN 40 V 1 2 2, 3 4 Input voltage VINIOUT 1 mA 1, 2, 3 All 11.1 V Load regulation 4/ (sourcing current) OUTRIV0 mA IOUT 10 mA 1 All 25 PPM/mA2, 3 40Load regulation 4/ 5/ (shunt mode) SHUNTRIV1.7 mA ISHUNT 10 mA 1 All 100 PPM/mA2, 3 150Supply current (

23、series mode) ISNo load 1 All 1.7 mA 2, 3 2.0 Minimum current (shunt mode) IMINVINis open 1 All 1.5 mA 2, 3 1.7 1/ Unless otherwise specified, VIN= 15 V, IOUT= 0 mA, and TA= +25C. 2/ Output voltage is measured immediately after turn-on. Changes due to chip warm-up are normally less than 0.005 percent

24、. 3/ Temperature coefficient is measured by dividing the change in output voltage over the temperature range by the change in temperature. Separate tests are done for hot and cold; -55C to +25C and +25C to +125C. 4/ Line and load regulation is measured on a pulse basis. Output changes due to tempera

25、ture must be taken into account separately. 5/ Shunt mode regulation is measured with the input open. With the input connected, shunt mode current can be reduced to 0 mA. Load regulation will remain the same. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

26、HS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89802 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 FIGURE 1. Case outline X. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAW

27、ING SIZE A 5962-89802 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 Letter Inches MillimetersMin Max Min Max A .165 .185 4.19 4.70 b1 .016 .019 0.41 0.48 D .340 .370 8.64 9.40 D1 .305 .335 7.75 8.51 e .200 BSC 5.08 BSC e1 .100 BSC 2.54 BSC k .028 .034

28、 0.71 0.86 k1 .026 .045 0.66 1.14 L .500 - 12.70 - 45 45 NOTES: 1. Dimensions are in inches. 2. Metric equivalent are given for general information only. 3. Leads having a maximum diameter of 0.019 inch (0.48 mm) measured in gauging plane 0.54 inch 0.001 inch (1.37 mm 0.03 mm) below the base plane o

29、f the product shall be within 0.007 inch (0.18 mm) of their true position relative to the maximum tab width. FIGURE 1. Case outline X - continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89802 DLA LAN

30、D AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 FIGURE 2. Terminal; connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89802 DLA LAND AND MARITIME COLUMBUS, O

31、HIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PI

32、N number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicat

33、or “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL

34、-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformanc

35、e. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verific

36、ation and review. DLA Land and Maritime, DLA Land and Maritime s agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 4. VERIFICATION 4.1 S

37、ampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional c

38、riteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition C. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the i

39、nputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to bu

40、rn-in are optional at the discretion of the manufacturer. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a.

41、 Tests shall be as specified in table II herein. b. Subgroups 4, 5, 6, 7, 8, 9, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89802 DLA LA

42、ND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) 1 Final electrical test paramete

43、rs (method 5004) 1*,2,3 Group A test requirements (method 5005) 1,2,3 Groups C and D end-point electrical parameters (method 5005) 1,2,3 * PDA applies to subgroup 1. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life te

44、st conditions, method 1005 of MIL-STD-883. (1) Test condition C. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases,

45、 and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in

46、 accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing w

47、ill replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMDs. All proposed changes to existing SMDs will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692

48、, Engineering Change Proposal. 6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DLA Land and Maritime -VA, telephone (614) 692-0544. Provided by IHSNot for ResaleNo reprodu