DLA SMD-5962-89915 REV C-2011 MICROCIRCUIT LINEAR POSITIVE VOLTAGE REGULATOR 18 VOLT FIXED MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. - ro 01-02-15 R. MONNIN B Add a footnote to the case outline U, TO-257 package as specified under 1.2.2 and figure 1. - ro 05-01-19 R. MONNIN C Update boilerplate paragraphs to current MIL-PRF-3853

2、5 requirements. - ro 11-05-12 C. SAFFLE REV SHET REV SHET REV STATUS REV C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY MARCIA B. KELLEHER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING I

3、S AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, POSITIVE VOLTAGE REGULATOR, 18 VOLT FIXED, MONOLITHIC SILICON DRAWING APPROVAL DATE 93-06-29 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 6726

4、8 5962-89915 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E239-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89915 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR

5、97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89915 01 U A Drawing number

6、 Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 7818A Positive regulator, 18 volt fixed 1.2.2 Case outline(s). The case outline(s) are as designate

7、d in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style U 1/ See figure 1 3 TO-257, single row, flange mount, with isolated tab and glass sealed X See figure 1 3 TO-39, can Y See figure 1 2 TO-3, flange mount Z MBFM4-P2 2 Flange mount 2 CQCC1-N20 20 Square lea

8、dless chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Input voltage: Operating or output shorted to ground 35 V dc Transient . 50 V dc 2/ Power dissipation (PD): TC= +25C: Cases X and 2 . 2 W Case Y . 20 W Cases Z and U . 15

9、 W TA= +25C: Cases X and 2 . 1.0 W Case Y . 4.3 W Cases Z and U . 3.0 W _ 1/ For outline letter U, CAGE 34333 manufacturers the TO-257 package with ceramic seal. 2/ The 50 V input rating refers to the ability of the regulator to withstand high line or transient condition without damage. Since the re

10、gulators maximum current capability is reduced, the output may fall out of regulation at high input voltages under nominal loading. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89915 DLA LAND AND MARITIME

11、COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings - continued. Storage temperature range . -65C to +150C Lead temperature (soldering, 10 seconds) . +300C Junction temperature (TJ) . +150C 3/ Thermal resistance, junction-to-case (JC): Case U 4.2C/W

12、Case X 15C/W Case Y 3C/W Case Z 6C/W Case 2 . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Cases U and Z 42C/W Cases X and 2 . 120C/W Case Y 29C/W 1.4 Recommended operating conditions. Input voltage range (VIN) +17.5 V dc to +30 V dc Ambient operating temperature range (TA) -55C to

13、 +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or co

14、ntract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HAN

15、DBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 1

16、9111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _

17、3/ The device is protected by a thermal shutdown circuit which is designed to turn off the output transistor whenever the device junction temperature is in excess of +150C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING

18、 SIZE A 5962-89915 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. P

19、roduct built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan a

20、nd qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN

21、 as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A a

22、nd herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance c

23、haracteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking.

24、 Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has th

25、e option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accorda

26、nce with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA

27、 Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A s

28、hall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime s agent, an

29、d the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

30、-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89915 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Un

31、it Min Max Output voltage VOUTTA= +25C 1 01 17.7 18.3 V VIN= 21 V to 33 V 2/ 1,2,3 17.5 18.5 Line regulation 3/ 4/ VRLINEVIN= 21 V to 33 V, 1 01 20 mV -55C TJ +125C 2,3 50 VIN= 24 V to 30 V, 1 15 -55C TJ +125C 2,3 25 Load regulation 3/ VRLOADIOUT= 5.0 mA to 1.5 A, 5/ -55C TJ +125C 1 01 35 mV IOUT= 5

32、.0 mA to 1.0 A, 5/ -55C TJ +125C 2,3 75 IOUT= 250 mA to 5/ 750 mA, 1 21 -55C TJ +125C 2,3 45 IOUT= 5 mA to 500 mA, 6/ 1 50 -55C TJ +125C 2,3 75 Standby current drain ISCD1 01 6.0 mA 2,3 6.5 Standby current drain change with line ISCD(line) VIN= 21 V to 30 V 1,2,3 01 0.8 mA Standby current drain chan

33、ge with load ISCDIOUT= 5.0 mA to 1000 mA 5/ 1,2,3 01 0.5 mA IOUT= 5.0 mA to 500 mA 6/ 0.5 Dropout voltage VDOIOUT= 1.0 A, TA= +25C, VOUT= 100 mV 5/ 1 01 2.5 V IOUT= 500 mA, TA= +25C, VOUT= 100 mV 6/ 2.5 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitt

34、ed without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89915 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified

35、Group A subgroups Device type Limits Unit Min Max Peak output current IOUTTA= +25C 5/ 1 01 1.5 3.3 A (pk) TA= +25C 6/ 0.5 1.7 Short circuit current 7/ IOSVIN= 35 V 5/ 1 01 1.2 A 2,3 2.8 VIN= 35 V 6/ 1 0.7 2,3 2.0 Ripple rejection VIN/ VIN= 10 V, f = 120 Hz 4 01 59 dB VOUT5,6 8/ 57 Output noise volta

36、ge 8/ NOf = 10 Hz to 100 kHz, TA= +25C 7 01 40 V / Vrms Long term stability 8/ VOUT/ t t = 1000 hours, TA= +25C 7 01 150 mV 1/ Unless otherwise specified, VIN= 27 V and IOUT= 500 mA for cases U, Y, and Z, VIN= 27 V and IOUT= 100 mA for cases X and 2. Maximum test current for cases X and 2 is 500 mA.

37、 2/ For cases X and 2: IOUT= 5 mA to 500 mA, P 2 W. For case Y: IOUT= 5 mA to 1.0 A, P 20 W. For cases U and Z: IOUT= 5 mA to 1.0 A, P 15 W. 3/ All regulation tests are made at constant junction temperature with low duty cycle testing. 4/ Minimum load current for full line regulation is 5.0 mA. 5/ F

38、or cases U, Y, and Z only. 6/ For cases X and 2 only. 7/ Short circuit protection is only assured up to VIN= 35 V. 8/ Guaranteed, if not tested, to the limits specified in table I herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICRO

39、CIRCUIT DRAWING SIZE A 5962-89915 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Case outline U Inches mm .005 0.13 .010 0.25 .020 0.51 Symbol Inches Millimeters Min Max Min Max A .190 .200 4.83 5.08 A1.035 .045 0.89 1.14A2.120 BSC 3.05 BSC b .025 .035

40、 0.64 0.89 D .645 .665 16.38 16.89D1.410 .430 10.41 10.92 D3.000 .065 0.00 1.65e .100 BSC 2.54 BSC E .410 .422 10.41 10.72 L .500 .750 12.70 19.05O .527 .537 13.39 13.64 P .140 .150 3.56 3.81NOTES: 1. Dimensions are in inches. 2. Metric equivalent are given for general information only. 3. For case

41、outline U only, CAGE 34333, the ceramic seal that protrudes from the seating plane is not to be considered in overall package dimensions. The ceramic seal protrusion is considered uncontrolled within an area 30 mils from the seating plane. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo repr

42、oduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89915 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Case outline X Symbol Inches Millimeters Notes Min Max Min Max A .165 .185 4.19 4.70 b .016 .01

43、9 0.41 0.48 2 b1.016 .021 0.41 0.53 2 D .335 .370 8.51 9.40 D1.305 .335 7.75 8.51 e .200 BSC 5.08 BSC 4 e1.100 BSC 2.54 BSC 4 F - .050 - 1.27 k .028 .034 0.71 0.86 k1.029 .045 0.74 1.14 3 k2.009 .041 0.23 1.04 L .500 - 12.70 - L1- .050 - 1.27 L2.250 - 6.35 - 45 T.P. 45 T.P. 4 NOTES: 1. Dimensions sh

44、all be measured in inches. 2. Metric equivalents are given for general information only. 3. (All leads) b applies between L1and L2. b1applies between L2and .500 inch (12.70 mm) from the reference plane. Diameter is uncontrolled in L1and beyond .500 inch (12.70 mm) from the reference plane. 4. Measur

45、ed from the maximum diameter of the product. 5. Leads having a maximum diameter of .019 inch (0.48 mm) measured in gauging plane .054 inch (1.37 mm) + .001 (0.03 mm) - .000 inch (0.00 mm) below the base plane of the product shall be within .007 inch (0.18 mm) of their true-position relative to a max

46、imum width tab. 6. The product may be measured by direct method or by guage. FIGURE 1. Case outline Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89915 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-

47、3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 Case outline Y Symbol Inches Millimeters Notes Min Max Min Max A .250 .450 6.35 11.35 A11.177 1.197 29.90 30.40b .038 .043 0.97 1.09 2,6 D - .875 - 22.22 e .655 .675 16.64 17.74 e1.420 .440 10.67 11.16 e2.205 .225 5.21 5.72F .060 .135 1.52 3.43 H .

48、151 .161 3.84 4.09 4,5L .312 .500 7.92 12.70 3 L1- .050 - 1.27 2,3 R .495 .525 12.57 13.34 R1.131 .188 3.33 4.78NOTES: 1. Dimensions shall be measured in inches. 2. Metric equivalents are given for general information only. 3. (Two leads) b applies between L1and beyond .500 inch (12.70 mm) from the seating plane. Diameter is uncontrolled in L1and beyond .500 inch (12.70 mm) from the seating plane. 4. Two leads. 5. Two holes. 6. Two