DLA SMD-5962-89959 REV D-2009 MICROCIRCUIT DIGITAL CMOS 16-BIT CASCADABLE ALU MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update table I. Changes to timing waveforms. Add package Z. Editorial changes throughout. 92-11-05 M. L. Poelking B Add device types 02 and 03. Editorial changes throughout. 94-06-17 M. L. Poelking C Changes in accordance with Notice of Revision

2、(NOR) 5962-R055-96. LTG 96-02-02 M. L. Poelking D Convert drawing to Standard Microcircuit Drawing format and update the boilerplate to current MIL-PRF-38535 requirements. - PHN 09-06-24 Thomas M. Hess THE ORIGINAL FIRST PAGE OF THIS DRAING HAS BEEN REPLACED. REV SHEET REV D D D D D D D D D D D SHEE

3、T 15 16 17 18 19 20 21 22 23 24 25 REV STATUS REV D D D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Christopher A. Rauch DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY William K. Heckman COLUMBUS, OHIO 43218-3990 http:/www.dscc

4、.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY William K. Heckman MICROCIRCUIT, DIGITAL, CMOS, 16-BIT AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 90-09-11 CASCADABLE ALU, MONOLITHIC SILICON AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-89959 SHE

5、ET 1 OF 25 DSCC FORM 2233 APR 97 5962-E292-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89959 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. S

6、COPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89959 01 X X Drawing number Device

7、 type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 L4C381-45 ns 16-bit cascadable ALU 02 L4C381-30 ns 16-bit cascadable ALU 03 L4C381-25 ns 16-bit cascada

8、ble ALU 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X CMGA15-P68 68 Pin grid array Y CQCC1-N68 68 Square leadless chip carrier Z CMGA3-P68 68 Pin grid array 1.2.3 Lead finish. The lead finish i

9、s as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Storage temperature range . -65C to +150C Maximum power dissipation (PD) 1/ 420 mW VCCsupply voltage range with respect to ground -0.5 V dc to +7.0 V dc Input signal voltage range with respect to ground . -0.3 V dc to +7.0 V

10、dc Signal voltage range applied to high impedance outputs -0.3 V dc to +7.0 V dc Current into low outputs. 25 mA Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ) +175C Thermal resistance, junction-to-case (JC). See MIL-STD-1835 1.4 Recommended operating conditions. Supply vol

11、tage range (VCC) . 4.5 V dc to 5.5 V dc Case operating temperature range (TC) -55C to +125C _ 1/ Must withstand the added PDdue to short circuit test; e.g., IOS. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 596

12、2-89959 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified he

13、rein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Micro

14、circuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksear

15、ch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this documen

16、t, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built

17、 to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifyin

18、g activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as describe

19、d herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3

20、.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Functional block diagram. The functional block diagram shall be as specified on figure 2. 3.2.4 Truth tables. The truth tables

21、 shall be as specified on figure 3. 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 4. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in ta

22、ble I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproduction or netw

23、orking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89959 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked w

24、ith the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A

25、compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, Appendix A. The compliance indicator “C” shall be replaced with a “Q” or “QML” certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of co

26、mpliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.7 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers

27、product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notif

28、ication of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made avail

29、able onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89959 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE

30、I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output high voltage VOHIOH= -2 mA, VCC= 4.5 V 1, 2, 3 All 2.4 V Output low voltage VOLIOL= 8 mA, VCC= 4.5 V 0.5 V Input high

31、 voltage VIH2 V Input low voltage VIL0 V Input current IIXVCC= 5.5 V 20 A Output leakage current IOZVCC= 5.5 V 20 A Dynamic supply current ICC1VCC= 5.5 V 2/ 30 mA Quiescent supply current ICC2VCC= 5.5 V 3/ 1.5 mA Input capacitance CINf = 1.0 MHz, VCC= 5.0 V, See 4.3.1c VIN= 0 V 4 5 pF VOUT= 0 V 8 Fu

32、nctional tests VCC= 4.5 V and 5.5 V See 4.3.1d 7, 8 Clock to F0 F15 1 FTAB = 0, FTF = 0, CL= 30 pF, VCC= 4.5 V See figure 4. 9, 10, 11 01 28 ns 02 26 03 14 Clock to P, G 2 01 34 ns 02 28 03 24 Clock to OVF, ZERO 3 01 50 ns 02 34 03 24 Clock to C16 4 01 34 ns 02 28 03 24 C0 to OVF, ZERO 5 01 32 ns 02

33、 22 03 18 C0 to C16 6 01 23 ns 02 22 03 18 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89959 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET

34、6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Group A subgroups Device type Limits Unit Min Max S0 S2, OSA, OSB to P, G 7 FTAB = 0, FTF = 0, CL= 30 pF, VCC= 4.5 V See figure 4. 9

35、, 10, 11 01 38 ns 02 28 03 22 S0 S2, OSA, OSB to OVF ZERO 8 01 38 ns 02 28 03 24 S0 S2, OSA, OSB to C16 9 01 38 ns 02 28 03 22 Clock to F0 F15 10 FTAB = 0, FTF = 1, CL= 30 pF, VCC= 4.5 V See figure 4. 01 56 ns 02 34 03 25 Clock to P, G 11 01 34 ns 02 28 03 24 Clock to OVF, ZERO 12 01 50 ns 02 34 03

36、24 Clock to C16 13 01 34 ns 02 28 03 24 C0 to F0 F15 14 01 32 ns 02 26 03 21 C0 to OVF, ZERO 15 01 32 ns 02 22 03 18 C0 to C16 16 01 23 ns 02 22 03 18 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUI

37、T DRAWING SIZE A 5962-89959 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Group A subgroups Device

38、 type Limits Unit Min Max S0 S2, OSA, OSB to F0 F15 17 FTAB = 0, FTF = 1, CL= 30 pF, VCC= 4.5 V See figure 4. 9, 10, 11 01 46 ns 02 30 03 25 S0 S2, OSA, OSB to P, G 18 01 38 ns 02 28 03 22 S0 S2, OSA, OSB to OVF, ZERO 19 01 38 ns 02 28 03 24 S0 S2, OSA, OSB to C16 20 01 38 ns 02 28 03 22 A0 A15, B0

39、B15 to P, G 21 FTAB = 1, FTF = 0, CL= 30 pF, VCC= 4.5 V See figure 4. 01 32 ns 02 28 03 20 A0 A15, B0 B15 to OVF, ZERO 22 01 46 ns 02 28 03 25 A0 A15, B0 B15 to C16 23 01 36 ns 02 28 03 22 Clock to F0 F15 24 01 28 ns 02 26 03 14 C0 to OVF, ZERO 25 01 32 ns 02 22 03 18 See footnotes at end of table.

40、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89959 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics -

41、Continued. Test Symbol Conditions 1/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Group A subgroups Device type Limits Unit Min Max C0 to C16 26 FTAB = 1, FTF = 0, CL= 30 pF, VCC= 4.5 V See figure 4. 9, 10, 11 01 23 ns 02 22 03 18 S0 S2, OSA, OSB to P, G 27 01 38 ns 02 28 03 22 S0 S2, OS

42、A, OSB to OVF, ZERO 28 01 38 ns 02 28 03 24 S0 S2, OSA, OSB to C16 29 01 38 ns 02 28 03 22 A0 A15, B0 B15 to F0 F15 30 FTAB = 1, FTF = 1, CL= 30 pF, VCC= 4.5 V See figure 4. 01 45 ns 02 30 03 25 A0 A15, B0 B15 to P, G 31 01 32 ns 02 28 03 20 A0 A15, B0 B15 to OVF, ZERO 32 01 46 ns 02 28 03 25 A0 A15

43、, B0 B15 to C16 33 01 36 ns 02 28 03 22 C0 to F0 F15 34 01 32 ns 02 26 03 21 C0 to OVF, ZERO 35 01 32 ns 02 22 03 18 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89959 DEFENS

44、E SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 9 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Group A subgroups Device type Limits Unit Min Max C0 to C1

45、6 36 FTAB = 1, FTF = 0, CL= 30 pF, VCC= 4.5 V See figure 4. 9, 10, 11 01 23 ns 02 22 03 18 S0 S2, OSA, OSB to F0 F15 37 01 46 ns 02 30 03 25 S0 S2, OSA, OSB to P, G 38 01 38 ns 02 28 03 22 S0 S2, OSA, OSB to OVF, ZERO 39 01 38 ns 02 28 03 24 S0 S2, OSA, OSB to C16 40 01 38 ns 02 28 03 22 Clock (OSA,

46、 OSB = 0) to F0 F15 65 01 56 ns 02 34 03 25 Clock (OSA, OSB = 0) to P, G 41 01 34 ns 02 28 03 24 Clock (OSA, OSB = 0) to OVF, ZERO 42 FTAB = 1, FTF = 1, CL= 30 pF, VCC= 4.5 V See figure 4. 01 50 ns 02 34 03 24 Clock (OSA, OSB = 0) to C16 43 01 34 ns 02 28 03 24 A0 A15, B0 B15 set-up time 44 FTAB = 0

47、 CL= 30 pF, VCC= 4.5 V See figure 4. 01, 02 8 ns 03 7 A0 A15, B0 B15 hold time 45 01, 02 3 ns 03 0 A0 A15, B0 B15 set-up time 46 FTAB = 1 CL= 30 pF, VCC= 4.5 V See figure 4. 01 33 ns 02 20 03 14 A0 A15, B0 B15 hold time 47 01, 02 3 ns 03 0 See footnotes at end of table. Provided by IHSNot for Resale

48、No reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89959 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 10 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Group A subgroups Device type Limits Unit Min Max EN