DLA SMD-5962-89972 REV D-2009 MICROCIRCUIT HYBRID LINEAR HIGH SPEED HIGH VOLTAGE VIDEO AMPLIFIER.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R136-94. 94-03-28 Kendall A. Cottongim B Changes in accordance with NOR 5962-R272-94. 94-09-09 Kendall A. Cottongim C Update drawing boilerplate to current requirements of MIL-PRF-38534. 01-05-30 Raymond Monnin

2、 D Table II, add note to Group C end-point test parameters. -gz 09-06-16 Joseph D. RodenbeckREV SHEET REV SHEET REV STATUS REV D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Steve Duncan DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Micha

3、el C. Jones COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, LINEAR, HIGH AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-01-13 SPEED, HIGH VOLTAGE, VIDEO AMPLIFIER AMSC N/A

4、 REVISION LEVEL D SIZE A CAGE CODE 67268 5962-89972 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E354-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89972 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3

5、990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). Whe

6、n available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 89972 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator

7、 (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The

8、device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 MSK 1902B-0 High voltage video amplifier 02 MSK 1902B-2 High voltage video amplifier 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product as

9、surance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class

10、 available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class

11、 H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes

12、(K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer sp

13、ecified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89972 DEFE

14、NSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 30 Flat pack, flange mount 1.2

15、.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ High voltage supply (+VHVor +VHVRES) +110 V dc Positive supply voltage (VCC) +17 V dc Negative supply voltage (VEE). -12 V dc Common mode input voltage 2 V dc Differential input voltage . 2 V dc

16、Gain adjust input voltage range (VGAIN) -0.6 V dc to +6 V dc Offset adjust input voltage range (VOFF) . -0.6 V dc to +6 V dc Blank input voltage range (VBLANK) -0.6 V dc to +6 V dc Reference output current (IOUT) 5 mA Power dissipation (PD) . 13 W Junction temperature (TJ) . +150C Thermal resistance

17、, junction-to-case (JC) . 13C/W 2/ Storage temperature range -65C to +150C Lead temperature (soldering, 10 seconds). +300C Total current through RP, (device type 02 only) 290 mA 1.4 Recommended operating conditions. Power on sequence +VHV, VCC, VEEHigh voltage supply (-VHVor -VHVRES) +30 V dc to +10

18、5 V dc Positive supply voltage (VCC) +15 V dc Negative supply voltage (VEE). -10.5 V dc Input voltage (excluding VCM) . 0.714 V Gain adjust input voltage range (VGAIN) 0 V dc to +5 V dc Offset adjust input voltage range (VOFF) . 0 V dc to +5 V dc Blank input voltage (VBLANK) TTL levels Reference out

19、put current (IOUT) 4 mA Case operating temperature range (TC) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified,

20、the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for

21、Electronic Component Case Outlines. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Thermal resistance is specified for the output transistors of the device. Provided

22、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89972 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Stan

23、dard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence

24、. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements

25、. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for

26、the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit

27、, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein and figur

28、e 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating tempera

29、ture range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be ma

30、rked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked in MIL-HDBK-103 and QML-38534. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical te

31、st data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revi

32、sion level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted

33、to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION

34、 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for

35、ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89972 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Test Symbol Condi

36、tions 1/ -55C TC+125C unless otherwise specified Group A subgroups Device type Min Max Unit ICC VCM= 0 V, VCC= +15 V dc 100 Quiescent current IEEVCM= 0 V, VEE= -10.5 V dc 1,2,3 All -100 mA 1 -50 +50 Input bias current IIBVCM= 0 V 2,3 All -250 +250 A VBLANK= 0.4 V, TA= +25C 600 Blank input current IB

37、LANK VBLANK= 2.4 V, TA= +25C 1 All 400 A Reference output voltage VOUTIOUT 2 mA 1,2,3 All 5.2 5.8 V V Blank mode VBMV = +VHV- VOUT, VBLANK= 2.4 V, VOFF= 1 V, VGAIN= 5 V 1,2,3 All -3xRP+3xRP mV V Minimum offset VMOFFV = +VHV- VOUT, VOFF= 0 V, VGAIN= 3 V 1,2,3 All 0 10V 1 01,02 +32 +5201 +28 +56 V Max

38、imum offset VMOFF1V = +VHV- VOUT, VOFF= +5 V 2,3 02 +32 +52 V Output high voltage 2/ VOHVGAIN= 3 V, f = 10 kHz 4,5,6 All 95 V Output low voltage 2/ VOLVGAIN= 3 V, f = 10 kHz 4,5,6 All 20 V Power supply rejection ratio 2/ PSRR VCC= 15 V 5%, VEE= -10.5 V5% 1,2,3 All 25 dB Common mode rejection ratio 2

39、/ CMRR VCM= 0.5 V, f = 10 kHz 4,5,6 All 35 dB Voltage gain 3/ VGAIN VGAIN= 3 V, VIN= 0.6 V, f = 10 kHz, both inputs 4,5,6 All 72 138 V/V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE

40、 A 5962-89972 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions 1/ -55C TC+125C unless otherwise specified Group A subgroups Device type Min Max Unit Linea

41、rity error 2/ LE VGAIN= 4 V, VOFF= 1 V, VCM= 0.5 V, TA= +25C 4 All -2 +2 %GS 4/ Thermal distortion 2/ thd TA= +25C 4 All -2 +2 %GS 4/ Gain linearity 2/ AVL VIN= 0.2 V, VOFF= 1 V, VCM= 0.5 V, TA= +25C 4 All -2 +2 % Input impedance 2/ RINf = DC, either input, TA= +25C 4 All 10 k Input capacitance 2/ C

42、INEither input, TA= +25C 4 All 3 pF Blank mode input rejection 2/ BMIR VBLANK= 2.4 V, VIN= 0.3 V, V = +VHV- VOUT, TA= +25C 4 All -2xRP+2xRP mV Gain adjust rejection 2/ GAR VGAIN= 5 V, TA= +25C 4 All -10xRP +10xRP mV 01 5.5 Transition times 2/ TT VIN= 0.6 V, VOUT= 70 Vp-p, tr= tf 1 ns 4,5,6 02 4.0 ns

43、 Blank input pulse width 2/ tBLANK Normal operation 4 All 30 ns 01 0 2 Internal RP2/ 5/ RP Pins 16 and 17, f = dc, TA= +25C 1 02 380 420 1/ VCC= +15 V dc, VEE= -10.5 V dc, +VHV= +100 V dc, VBLANK= 0.4 V dc, CL = 10 pF, RP= 400 , VGAIN= VOFF= VIN= 0 V, unless otherwise specified. 2/ Parameter if not

44、tested, shall be guaranteed to the limits specified in table I. 3/ For VGAINsubgroups 5 and 6 shall be guaranteed to the limits specified in table I for all lots not specifically tested. Subgroup 4 shall be tested every lot. 4/ %GS means percent of gray scale, referring to the RS-343 standard video

45、levels. 5/ Total RPis defined as 400 + user external RPif used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89972 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FOR

46、M 2234 APR 97 Case outline X. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89972 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR

47、 97 Case outline X - Continued. Millimeters Inches Symbol Min Max Min Max A 25.15 25.65 .990 1.010 B 37.85 38.35 1.490 1.510 C 25.15 25.65 .990 1.010 D 6.10 6.60 .240 .260 E 10.16 - .400 - F 2.95 3.05 .116 .120 G 3.56 4.06 .140 .160 H 8.64 9.14 .340 .360 I 2.29 2.79 .090 .110 J 17.27 18.29 .680 .720

48、 K 3.56 4.06 .140 .160 L 17.53 18.03 .690 .710 M 0.30 0.46 .012 .018 N - 5.08 - .200 P 0.20 0.30 .008 .012 Q 1.27 TYP .050 TYP X 2.29 2.92 .090 .115 NOTES: 1. The U. S. preferred system of measurement is the metric SI. This case outline was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound shall take precedence. 2