DLA SMD-5962-89986 REV D-2011 MICROCIRCUIT HYBRID LINEAR 16-BIT DIGITAL TO SYNCHRO AND DIGITAL TO RESOLVER CONVERTER.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R159-95. 95-06-16 Kendall A. Cottongim B Add vendor CAGE S7631. Paragraph 1.3, add operating temperature range. Table I, AOTR test, correct limits from 0.2% to 0.5%. Table I, SFV test, correct limits from 0.05%

2、 to 0.1%. Figure 1, case outline X, convert case outline dimensioning to symbol and inches/millimeters table. Update drawing boilerplate. 03-04-10 Raymond Monnin C Rewrite paragraphs 4.2.a.2. and 4.3.3.b.2 to add TC. 04-04-23 Raymond Monnin D Updated drawing paragraphs. -sld 11-12-06 Charles F .Saff

3、le THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED REV SHEET REV SHEET REV STATUS REV D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Shelly Jenkins DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIR

4、CUIT DRAWING CHECKED BY Michael C. Jones THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE APPROVED BY D. R. Cool MICROCIRCUIT, HYBRID, LINEAR, 16-BIT, DIGITAL TO SYNCHRO AND DIGITAL TO RESOLVER CONVERTER DRAWING APPROVAL DATE 92-02-10 AMSC N/A REVISION L

5、EVEL D SIZE A CAGE CODE 67268 5962-89986 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E048-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89986 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D

6、 SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choic

7、e of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 89986 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.

8、2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) ident

9、ify the circuit function as follows: Device type Generic number Circuit function Accuracy 01 DSC-11520-112 16-bit D/S and D/R converter 8 minutes 02 DSC-11520-113 16-bit D/S and D/R converter 4 minutes 03 DSC-11520-114 16-bit D/S and D/R converter 2 minutes 04 DSC-11520-115 16-bit D/S and D/R conver

10、ter 1 minutes 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G a

11、nd D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high

12、reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) per

13、iodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition docu

14、ment should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for Re

15、saleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89986 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as

16、follows: Outline letter Descriptive designator Terminals Package style X See figure 1 36 Dual-in-line 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. Positive supply voltage (VCC) . +18 V dc Negative supply voltage (VEE) 18 V dc Reference inpu

17、t (RH, RL) 30 V rms Digital input voltage (BITS 1-16) -0.3 V dc to +6.5 V dc Power dissipation, TC= +125C (PD) . .72 W Storage temperature range -65C to +150C Lead temperature (soldering, 10 seconds) +300C Thermal resistance junction-to-case (JC) 8.0C/W Thermal resistance junction-to-ambient (JA) .

18、20C/W 1.4 Recommended operating conditions. Positive supply voltage range (VCC) . +14.25 V dc to +15.75 V dc Negative supply voltage range (VEE) 14.25 V dc to -15.75 V dc Case operating temperature range (TC) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbo

19、oks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits,

20、 General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Micro

21、circuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this dr

22、awing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Exte

23、nded operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89986 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEE

24、T 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device

25、 manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In additio

26、n, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s).

27、 The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Block diagram. The block diagram shall be as specified on figure 3. 3.2.4 Timing diagram. The timing diagram shall be as specified

28、 on figure 4. 3.2.5 Pin functions. The pin functions shall be as specified on table III. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature

29、 range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked

30、 with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from th

31、e initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufact

32、urer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and

33、Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATI

34、ON 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot fo

35、r ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89986 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C

36、TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Resolution, 16-bit RES MSB = 180 degrees LSB = .0055 degrees 7,8 All .33 arc min Output accuracy AOUT7,8 01 -8 +8 min 02 -4 +4 03 -2 +2 04 -1 +1 Differential linearity 2/ DL 7,8 All -1 +1 LSB Radius accuracy 2/ RA

37、3/ 7,8 All -.03 +.03 % Output settling time 2/ tSFor any analog or digital step change 9,10,11 All 20 s Logic 0 digital input voltage 4/ VIL1,2,3 All -.3 1.25 V Logic 1 digital input voltage 4/ VIH1,2,3 All 2.0 5.5 V Digital input load current 2/ IINBits 1 through 16, VIN= 0 V 1,2,3 All -20 A LL, LM

38、, and LA, VIN= 5.0 V 1,2,3 All +20 A Standard reference input voltage (RH, RL) 2/ VIN4,5,6 All 23.4 28.6 V rms Reference input frequency fIN4,5,6 All 1.0 kHz Standard reference input impedance (RH, RL) 2/ ZINSingle ended 4,5,6 All 99.5 100.5 k Differential 4,5,6 All 199 201 k Analog output current 4

39、/ IOUTShort circuit protected 4,5,6 All 2 mA rms Analog output voltage VOUT Resolver 4,5,6 All 6.753 6.817 V rms L-L Synchro 2/ 4,5,6 All 11.77 11.83 V rms L-L See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MI

40、CROCIRCUIT DRAWING SIZE A 5962-89986 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Uni

41、t Min Max Analog output transformation ratio 2/ AOTR 4,5,6 All -0.5 +0.5 % Analog output impedance 2/ ZOUTOp amp output 4,5,6 All 1 ohm Analog output offset voltage 2/ VOSEach line to ground 1,2,3 All -15 +15 mV Analog output scale factor variation 2/ SFV 7,8 All -0.1 +0.1 % Register latch control L

42、L, LM, LA; data latched 7,8 All Pass/ Fail LL, LM, LA; data transparent 7,8 All Register control pulse width 2/ tPWFor data transfer, see figure 4 9,10,11 All 200 ns Register control data setup time 2/ tsuBefore data transfer, see figure 4 9,10,11 All 50 ns Register control data hold time 2/ thHold

43、time after low edge of LL, LM, LA, see figure 4 9,10,11 All 100 ns Positive supply current (VCC) 4/ ICCVCC= +15 V dc 1,2,3 All +20 mA Negative supply current (VEE) 4/ IEEVEE= -15 V dc 1,2,3 All -20 mA 1/ +14.25 V dc VCC +15.75 V dc, -14.25 V dc VEE -15.75 V dc. 2/ Parameter shall be tested as part o

44、f device initial characterization and after design and process changes. Parameter shall be guaranteed to the limits specified in table I for all lots not specifically tested. 3/ Radius accuracy is defined as the simultaneous amplitude variation in both outputs as a function of digital angle. 4/ Test

45、ed on a go-no-go basis in conjunction with other tested parameters and not directly testable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89986 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEV

46、EL D SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Symbol Millimeters Inches Minimum Maximum Minimum Maximum A - 5.33 - .210 b 0.46 TYP .018 TYP D 48.01 48.26 1.890 1.900 D1 43.05 43.31 1.695 1.705 E 19.56 19.81 .770 .780 e 2.54 TYP .100 TYP eA 15.11 15.37 .595 .605 L 6.10 - .240 - L1 - 0.38 - .015

47、R1 2.18 TYP .086 TYP R2 1.40 TYP .055 TYP S 2.03 2.54 .080 .100 S1 2.29 2.79 .090 .110 NOTES: 1. Dot on lid of package indicates pin 1. 2. Lead identification numbers are for information only. 3. Lead spacing dimensions apply only at seating plane. 4. The U.S. government preferred system of measurem

48、ent is the metric SI. This case outline was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. FIGURE 1. Case outline(s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-